Abstract:In a stress state dominated by shear, pre-existing voids rotate, elongate, and close up to form micro-cracks, which interact through void coalescence and eventually may cause a complete loss of load-carrying capacity. The mechanism sets apart void coalescence in shear from that under tensile-dominated stress states, and the present work demonstrates that gradient strengthening affects the macroscopic strain at the onset of plastic flow localization leading to coalescence. Despite that zero or limited void growth develop in shear, a severe heterogeneous plastic straining develops near the void, which generates large plastic strain gradients accompanied by densities of Geometrically Necessary Dislocations (GNDs) in addition to the Statistically Stored Dislocations (SSDs) that controls conventional strain hardening. The GNDs lead to additional micron scale strengthening, and the present work investigates their effect on the plastic flow localization leading to void coalescence in shear by modeling voids embedded in a gradient-enhanced matrix material, thus revisiting the early work by Tvergaard (2008), which was carried out in a conventional scale independent setting. The Fleck–Willis gradient theory is assumed to govern the matrix surrounding the voids such that a material length parameter enters the analysis. Increasing the length parameters while keeping the void volume fraction and intervoid distance constant corresponds to diminishing the material microstructure. The results show that (i) voids with the minor axis in the direction of the shear (denoted “prolate”), give the highest ductility mainly due to the larger intervoid ligament; (ii) both the initial relative void size and the initial void orientation have strong effects on material ductility across the scales; (iii) the initial void orientation plays a fundamental part in the void deformation mechanism and the plastic field that develops prior to coalescence; (iv) the ductility increases substantially when down-scaling the microstructure where the gradient strengthening intensifies (corresponding to increasing the material length parameter). Throughout, fitting functions for the average shear angle at the onset of plastic flow localization are suggested, with respect to the relative void size, the initial void orientation, and the intrinsic material length parameter, to bring out the dependencies and facilitate using the unit cell results in continuum models.

Theoretical study of void closure in nonlinear plastic materials

Cylindrical Void in a Rigid-Ideally Plastic Single Crystal. Part I: Anisotropic Slip Line Theory Solution for Face-Centered Cubic Crystals

A criterion for void closure in large ingots during hot forging

An elastic-plastic cohesive zone model for metal-ceramic interfaces at finite deformations

Cylindrical void in a rigid-ideally plastic single crystal II: Experiments and simulations

Cylindrical void in a rigid-ideally plastic single crystal III: Hexagonal close-packed crystal

A detailed study on void growth and crack-void interaction in plastically compressible bilinear hardening and trilinear hardening-softening-hardening solids

A novel model to predict microvoid evolution in tensile necking using macroscopic deformation behavior

A 3-D Model for Void Evolution in Viscous Materials under Large Compressive Deformation

An Effective Numerical Approach for Multiple Void-Crack Interaction

Development of local plasticity around voids during tensile deformation

Modelling the effects of void swelling and spatial heterogeneity on the fracture of metallic materials by crystal plasticity

A unified model for yield strength and plastic behavior of nanovoid evolution in tungsten based on molecular dynamics simulations

Experimental investigation into plastic damage of microvoids with interaction

Coupled crystal plasticity and micromechanics damage model based on viscoplastic self-consistent theory and X-ray computed tomography

Investigation on the Void Closure Efficiency in Cogging Processes of the Large Ingot by Using A 3-D Void Evolution Model

Study on the Growth Behavior of Voids Located at the Grain Boundary

Void Size, Shape, and Orientation Effects in Shear-Dominated Void Coalescence Across Scales

Effects of void shape and location on the fracture and plastic deformation of Cu (crystalline) /Cu 64 Zr 36 (amorphous) composites

Elastic-Plastic Fracture Behavior Analysis On A Griffith Crack In The Cylindrical Three-Phase Composites With Generalized Irwin Model

A Void Closure Model Based on Hydrostatic Integration and the Lode Parameter for Additive Manufacturing AlSi10Mg