Abstract:Improving efficiency and stability becomes two urgent issues towards the application of the perovskite solar cells (PSCs). Here in this article, a kind of long chain polymer or polymethylmethacrylate (PMMA, 350,000 in molecule weight) is added into the spiro-OMeTAD matrix to improve the film formation process and hence the device performance. It was observed that, after the modification, the spiro-OMeTAD basing hole-transporting layer (HTL) became uniform, continuous and condensed. Meanwhile, the power conversion efficiency of the devices was upgraded. Compared with control device (without PMMA modification), open-circuit voltage (VOC) of the modified one (with moderate doping) increased from 1.06 (±0.03) V to 1.10 (±0.02) V, fill factor (FF) raised from 72.20 (±3.44) % to 75.59 (±3.35)%, and the PCE upgraded from 18.82 (±1.06)% to 20.51 (±0.82) % (highest at 21.78%) at standard test condition (AM 1.5G, 100 mW/cm2). Transient photocurrent/photovoltage decay curves, time-resolved photoluminance and impedance spectroscopy studies showed that, the modification could accelerate charge transfer and retard interfacial recombination. In addition, the modification improved device stability. Due to the strengthened barrier against penetration of "H2O/O2 /Ag", efficiency of unsealed device could retain 91.49% (by average) of the initial one after 100 day-storage in dark [RH=30(±5)%]. This work shows that, long-chain polymer doping could simultaneously improve efficiency and stability of spiro-OMeTAD HTL basing PSCs.This article is protected by copyright. All rights reserved.

Modification of TiO 2 Electrode Films in Dye-Sensitized Solar Cells with PMMA

Enhancing the Performance of Nanocrystalline TiO2 Dye-Sensitized Solar Cells with Phenothiazine-Doped Blended Solid Polymer Electrolyte

A Simple and Efficient Method Using Polymer Dispersion to Prepare Controllable Nanoporous TiO2 Anodes for Dye-Sensitized Solar Cells

TiO 2 Film Decorated with Highly Dispersed Polyoxometalate Nanoparticles Synthesized by Micelle Directed Method for the Efficiency Enhancement of Dye-Sensitized Solar Cells

Improvement of performance of dye-sensitized solar cell by using composite nanoparticulate photoelectrode films

Thickness-dependent electron transport performance of mesoporous TiO2 thin film for dye-sensitized solar cells

Enhanced performance of dye-sensitized solar cell via surface modification of mesoporous TiO2 photoanode with electrodeposited thin TiO2 layer

Photovoltaic Performance of Dye-Sensitized Solar Cell by Modification of Photoanode With PbTiO 3 –ZnFe 2 O 4 /TiO 2 Nanofibers

A Bi-layer Composite Film Based on TiO 2 Hollow Spheres, P25, and Multi-walled Carbon Nanotubes for Efficient Photoanode of Dye-sensitized Solar Cell

Macro-mesoporous TiO2 Microspheres for Highly Efficient Dye-Sensitized Solar Cells

The TiO2 Films with Sandwich-Type Polyoxometalates in Dye Sensitized Solar Cells with Electron Recombination Decreasing and Dye Adsorption Increasing

Simultaneous Improvement of the Power Conversion Efficiency and Stability of Perovskite Solar Cells by Doping PMMA Polymer in Spiro‐OMeTAD‐Based Hole‐Transporting Layer

Improving of the Photovoltaic Characteristics of Dye-Sensitized Solar Cells Using a Photoelectrode with Electrospun Porous TiO2 Nanofibers

Enhancement of the Photoelectric Performance of Dye-sensitized Solar Cells by Sol-gel Modified TiO2 Films

BaCO3 Modification of TiO2 Electrodes in Quasi-Solid-State Dye-Sensitized Solar Cells: Performance Improvement and Possible Mechanism

Effect of the Addition of Ti<sup>3+</sup> into TiO<sub>2</sub> Film on the Performance of Dye Sensitized Solar Cells

Enhanced Photoelectric Conversion Of Dye-Sensitized Solar Cell By Addition Of Inorganic Particles

Performance Improvement of Dye-Sensitized Solar Cell by Optimizing TiO<sub>2</sub>-Photoanode Structure

TiO2 surface modification and characterization with nanosized PbS in dye-sensitized solar cells.

Indirect Preparation of Titanium Dioxide Oxidation Plating Layer as Photoelectrode Used in Dye-Sensitized Solar Cells

Preparation of Mesoporous Titanium Dioxide Anode by A Film- and Pore-Forming Agent for the Dye-Sensitized Solar Cell