Abstract:Melt-spun Al 75− X Si 25 Ni X ( X = 2, 4, 7, and 10 mol%) alloys were investigated as anode materials for lithium-ion batteries. The Al 68 Si 25 Ni 7 anode showed a maximum capacity of 840 mA h g −1 at the fifth cycle and maintained 661 mA h g −1 after 40 cycles with a high coulumbic efficiency of 93%. The specific capacity increased as the decrease in the Ni content during the first 20 cycles, but the cycle performance became poorer. For the Al 65 Si 25 Ni 10 anode, the specific capacity increased slowly as the cycles increased and reached 370 mA h g −1 after 40 cycles. When the Al 68 Si 25 Ni 7 ribbons were annealed, their initial capacity became higher, but much poorer cycle performance and low coulumbic efficiency occurred. Except Al 65 Si 25 Ni 10, the AlLi compound could be detected in the anodes after lithiation. However, the capacity faded rapidly due to the formation of excessive AlLi in the Al 73 Si 25 Ni 2 and annealed Al 68 Si 25 Ni 7 anodes. The experiments revealed that the as-quenched ribbons consisted of the nanoscaled α-Al, metallic glass and α-Si, and their fractions were dependent on the Ni content. The α-Al was a supersaturated solid solution of Si and Ni in fcc-Al. For the as-quenched Al 68 Si 25 Ni 7 ribbons, the α-Al grains were embedded in the amorphous matrix. It can be understood that metallic glass can store Li, and the supersaturated solid solution can store Li even more easily compared with other known Al–Si-based alloys. A conclusion can be drawn that the microstructure that the nanoscaled α-Al embedded in the metallic glass matrix is beneficial to improve the structure stability, restrain serious structural evolution, and limit the volume variation and pulverization during electrochemical cycles.

Exploration of Alnico Alloy As a Magnetic Electrode Material for Lithium-Ion Batteries

Ndfeb Alloy As A Magnetic Electrode Material for Lithium-Ion Batteries

Aluminum−lithium alloy as a stable and reversible anode for lithium batteries

The electrochemical properties of Al–Si–Ni alloys composed of nanocrystal and metallic glass for lithium-ion battery anodes

Al Substitution Induced Differences in Materials Structure and Electrochemical Performance of Ni-Rich Layered Cathodes for Lithium-Ion Batteries

A Novel 3D Li/Li9Al4/Li‐Mg Alloy Anode for Superior Lithium Metal Batteries

An In-Depth Understanding of the Effect of Aluminum Doping in High-Nickel Cathodes for Lithium-Ion Batteries

Single-material Aluminum Foil As Anodes Enabling High-Performance Lithium-Ion Batteries: the Roles of Prelithiation and Working Mechanism

Synergistic Surface and Bulk Engineering with Li-Riched D Ual-Phase Li-Al a Lloy a Node for Rational Regulation of L Ithium Deposition

A Stable Porous Aluminum Electrode with High Capacity for Rechargeable Lithium-Ion Batteries

Development of low-carbon energy storage material: Electrochemical behavior and discharge properties of iron-bearing Al–Li-based alloys as Al–air battery anodes

The structure and electrochemical performance of spherical Al-substituted ?-Ni(OH) for alkaline rechargeable batteries

Electrochemical Properties of Nanostructured Al[sub 1−x]Cu[sub x] Alloys as Anode Materials for Rechargeable Lithium-Ion Batteries

Role of Al-doping with Different Sites Upon the Structure and Electrochemical Performance of Spherical LiNi0.5Mn1.5O4 Cathode Materials for Lithium-Ion Batteries

In Operando magnetometry study on the charge storage mechanism of SnCo alloy lithium ion batteries

The Progress On Aluminum-Based Anode Materials For Lithium-Ion Batteries

Investigation of the Commercial Aluminum Alloys as Anode Materials for Alkaline Aluminum-air Batteries

Investigation of Immiscible Alloy System of Al–Sn Thin Films As Anodes for Lithium Ion Batteries

Performances of Al-xLi alloy anodes for Al-air batteries in alkaline electrolyte

Aluminum-Doped Lithium Nickel Cobalt Oxide Electrodes for High-Power Lithium-Ion Batteries

Spatially confined transition metals boost high initial coulombic efficiency in alloy anodes