Abstract:In this work, five alloys, Al − Mg, Al − Ce, Al − Ti, Al − Mg − Ce and Al − Mg − Ti, were prepared, and the electrochemical properties and discharge behavior of pure Al and these alloys were investigated in 4 M KOH solution. Corrosion experiments and electrochemical tests were performed, including open circuit potential test, electrochemical impedance spectroscopy test and polarization curve test. The performance of Al − air batteries based on these anodes was investigated by constant current discharge and V − j discharge tests. The surface state of the Al anodes after discharge was analyzed by scanning electron microscope and energy dispersive spectrometer. The results show that the addition of magnesium, cerium, and titanium to Al enhances its corrosion resistance, discharge voltage, peak power density, and specific capacity. Among the binary alloys, Al − Mg demonstrates superior corrosion resistance and higher no − load activity, while Al − Ce and Al − Ti exhibit higher discharge voltages and peak power densities. Additionally, the ternary alloys Al − Mg − Ce and Al − Mg − Ti, prepared using Al − Mg as the matrix, significantly reduce the corrosion rate and improve discharge performance. Al − Mg − Ce shows a maximum voltage of 1.21 V at 50 mA·cm − 2 , while Al − Mg − Ti displays a maximum voltage of 0.899 V at 100 mA·cm − 2 , with a peak power density of 97.0 mW·cm − 2 , surpassing that of Al − Mg − Ce (83.4 mW·cm − 2 ) and pure Al (72.8 mW·cm − 2 ). However, Al − Mg − Ti exhibits lower anode utilization compared to all binary alloys, while Al − Mg − Ce demonstrates higher anode utilization than Al − Mg, albeit slightly lower than that of Al − Ce and Al − Ti. The study highlights the potential of Al − Mg − Ce and Al − Mg − Ti alloys as effective strategies to enhance the performance of Al − air batteries. These findings contribute to the advancement of high − performance Al anodes and the optimization of Al − air battery design.

Performances of Al-xLi alloy anodes for Al-air batteries in alkaline electrolyte

Development of low-carbon energy storage material: Electrochemical behavior and discharge properties of iron-bearing Al–Li-based alloys as Al–air battery anodes

Electrochemical Performance of Al-1Zn-0.1In-0.1Sn-0.5Mg-xMn (x = 0, 0.1, 0.2, 0.3) Alloys Used as the Anode of an Al-Air Battery

Properties and composition of the spent electrolyte for premium circulation mediated by Al-air batteries.

Discharge performance of Al-0.1Sn-0.1In-0.05Ga alloy for Al–air battery anodes

Tailoring the discharge performance of extruded Mg-Sm-Al anode for Mg-air battery applications via control of Al content

Investigation of Commercial Aluminum Alloys As Anode Materials for Alkaline Aluminum–air Batteries

A Novel 3D Li/Li9Al4/Li‐Mg Alloy Anode for Superior Lithium Metal Batteries

Enhancing the Electrochemical Performance of Al-Mg-Sn-Ga Alloy Anode for Al-Air Battery by Solution Treatment

Aluminum−lithium alloy as a stable and reversible anode for lithium batteries

Investigation of the Commercial Aluminum Alloys as Anode Materials for Alkaline Aluminum-air Batteries

Discharge performance of the Al–Mg–Sn alloy anodes with different Sn content for Al-air batteries

The influence of Sn content on the electrochemical performance and discharge characteristics of Al-0.2Mg-0.02In-xSn-0.02Bi alloy anodes in aluminum-air batteries

A Porous Li-Al Alloy Anode toward High-Performance Sulfide-Based All-Solid-State Lithium Batteries

Performance improvement for aluminum-air battery by using alloying anodes prepared from commercially pure aluminum

High‐performance 3D Li‐B‐C‐Al Alloy Anode and its Twofold Li Electrostripping and Plating Mechanism Revealed by Synchrotron X‐ray Tomography

High performance Al anode for Al-air battery enabled by coordinating In and Sb additions with discharge parameters

The influence of cerium or titanium addition on the corrosion resistance and discharge performance of Al − mg anode for aluminum − air batteries

Plating/Stripping Behavior of Actual Lithium Metal Anode

The Strategy to Tune Li Stripping/Plating Behavior in Li Alloy Anode

Impact of aluminum alloy grade as anode on electrochemical performance for Al‐Air cell in alkaline electrolyte