Abstract:Research highlights ► Triazolyl blue tetrazolium bromide (TBTB) is found to be a novel good inhibitor for the corrosion of CRS in 1.0 M HCl and 0.5 M H 2 SO 4 solutions. ► The comparison of inhibition performance in HCl and that in H 2 SO 4 are discussed in detail. ► The corrosion inhibition is satisfactorily discussed by adsorption mode and thermodynamic parameter. ► The electrochemical inhibitive mechanism is explained by potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS) results. ► The adsorption of TBTB is presented. Abstract The inhibition effect of triazolyl blue tetrazolium bromide (TBTB) on the corrosion of cold rolled steel (CRS) in 1.0 M HCl and 0.5 M H 2 SO 4 solution was investigated for the first time by weight loss, potentiodynamic polarization curves, and electrochemical impedance spectroscopy (EIS) methods. The results show that TBTB is a very good inhibitor, and is more efficiency in 1.0 M HCl than 0.5 M H 2 SO 4 . The adsorption of TBTB on CRS surface obeys Langmuir adsorption isotherm. Polarization curves reveal that TBTB acts as a mixed-type inhibitor in both acids. Keywords A. Steel B. EIS B. Polarization B. Weight loss C. Acid inhibition 1 Introduction The use of inhibitors is one of the most practical methods for protection metal against corrosion, especially in acidic media [1] . As acidic media, hydrochloric acid (HCl) and sulfuric acid (H 2 SO 4 ) are often used as industrial acid cleaners and pickling acids. Among various acid organic inhibitors, N-heterocyclic compounds are considered to be the most effective corrosion inhibitors [2] . Up to now, many N-heterocyclic compounds with one or several N heteroatoms are reported as good corrosion inhibitors for iron or steel in acidic media, such as imidazoline derivatives [3–5] , 1,2,3-triazole derivatives [6] , 1,2,4-triazole derivatives [2,7–19] , pyrrole [20] , pyridine derivatives [21–23] , pyrazole derivatives [24–27] , bipyrazole derivatives [28–30] , pyrimidine derivatives [31] , pyridazine derivatives [32] , indole derivatives [33–35] , benzimidazole derivatives [36–40] , quinoline derivatives [41] , purine derivatives [42–44] . It is generally accepted that N-heterocyclic compounds exert their inhibition by adsorption on the metal surface through N heteroatom, as well as those with triple or conjugated double bonds or aromatic rings in their molecular structures. Furthermore, inhibition efficiency of N-heterocyclic organic inhibitor always increases with the number of aromatic systems and the availability of electronegative atoms in the molecule [7] . Besides containing N heteroatom, some N-heterocyclic compounds possessing N and O heteroatoms simultaneously such as isoxazolidines [45,46] , isoxazole derivatives [47] , benzoxazole derivatives [48] , oxadiazole derivatives [14,49–51] , have shown high efficiency for steel in acidic media. Other N-heterocyclic compounds containing N and S herteroatoms at the same time, like thiadiazole derivatives [52–56] , thiazole derivatives [57,58] and benzothiazole [59] were also widely used in protection steel corrosion in acid solutions. It has been assumed that the main adsorption of these N-heterocyclic compound inhibitors takes place through N heteroatom, as well as O and S herteroatoms in their molecular structures, and inhibition efficiency usually increase in the order: O < N < S. As another typical kind of N-heterocyclic compound, tetrazole derivatives whose molecules possess the tetrazole ring with 4-N heteroatoms have also been received some attention. In 1996, Kertit and Hammouti [60] studied the inhibition of 1-phenyl-5-mercapto-1,2,3,4-tetrazole (PMT) on the corrosion of iron in 1.0 M HCl, and its maximum inhibition efficiency ( E ) was 98% at 2 × 10 −3 M. Bensajjay et al. [61] extended their work to study the inhibition effect of PMT on steel in 0.5 M H 2 SO 4 and 1/3 M H 3 PO 4 . Results obtained showed that E also reached an optimum value of 98% at 10 −3 M PMT. Afterwards, Morales-Gil et al. [62] reported the inhibition effect of 5-mercapto-1-tetrazoleacetic sodium salt (MTAc) on steel in 1.0 M H 2 SO 4 . Their results showed that E was about 69% at 200 mg l −1 , while then decreased with the MTAc concentration. In our recent works [63–65] , the inhibition effect of red tetrazolium (RT) on the corrosion of cold rolled steel (CRS) in HCl, H 2 SO 4 and H 3 PO 4 solutions. The results show that maximum E value of 500 mg l −1 RT at 20 °C is 94% in 1.0 M HCl [63] ; 79%, 1.0 M H 2 SO 4 [64] ; and 63%, 3.0 M H 3 PO 4 [65] . Noticeably, these tetrazole compounds studied contain only one tetrazole ring, the literature available to date about the corrosion inhibition of the tetrazole compound which simultaneously possesses one tetrazole ring and another N-heterocyclic ring is very scarce. Triazolyl blue tetrazolium bromide (TBTB) is the tetrazole compound containing one tetrazole ring and one thiazole ring at the same time, which could be seemed as a good potential inhibitor. However, to the best of our knowledge, TBTB has not been treated as a corrosion inhibitor. In the present work, the inhibition effect of TBTB on cold rolled steel (CRS) in 1.0 M HCl and 0.5 M H 2 SO 4 solutions is studied for the first time by weight loss, potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS) methods. Meanwhile, the adsorption mode of TBTB on steel surface was obtained, and the adsorption free energyΔ G 0 were calculated and discussed. A probable inhibitive mechanism is proposed from the viewpoint of adsorption theory. 2 Experimental 2.1 Materials Tests were performed on a cold rolled steel (CRS) of the following composition (wt.%): 0.05% C, 0.28% Mn, 0.023% P, 0.019% S, 0.02% Si, and the remainder Fe. 2.2 Inhibitor Triazolyl blue tetrazolium bromide (TBTB, C 18 H 16 BrN 5 S) was obtained from Shanghai Chemical Reagent Company of China. Fig. 1 shows the molecular structure of TBTB. Clearly, it contains both tetrazole ring and thiazole ring (5-N heteroatoms and 1-S heteroatom). Thus, a great deal of lone electrons and π-electrons exists in this molecule. 2.3 Solutions The aggressive solutions of 1.0 M HCl and 0.5 M H 2 SO 4 was prepared by dilution of AR grade 37% HCl and 98% H 2 SO 4 with distilled water, respectively. The concentration range of TBTB employed was 0.02–0.50 mM (2.0 × 10 −5 to 5.0 × 10 −4 M). 2.4 Weight loss measurements The CRS sheets of 2.5 × 2.0 × 0.04 cm were abraded by a series of emery paper (grade 320–500–800) and then washed with distilled water, degreased with acetone, and finally dried with a cold air stream. After weighing accurately by digital balance with sensitivity of ±0.1 mg, the specimens were immersed in beaker containing 250 ml acid solution without and with different concentrations of TBTB using glass hooks and rods. The temperature was controlled at 30 ± 0.1 °C by a water thermostat. All the aggressive acid solutions were open to air. After immersion for 6 h, the specimens were taken out, washed with bristle brush under running water in order to remove the corrosion product, dried with a hot air stream, and reweighed accurately. In order to get good reproducibility, experiments were carried out in triplicate. The average weight loss of three parallel CRS sheets was obtained. The corrosion rate ( v ) is calculated by the following equation [64] : (1) v = W St where W is the average weight loss of three parallel CRS sheets, S the total area of one CRS specimen, and t is immersion time (6 h). With the calculated corrosion rate, the inhibition efficiency ( E w ) is calculated as follows [64] : (2) E w % = v 0 - v v 0 × 100 where v 0 and v are the values of corrosion rate without and with inhibitor, respectively. 2.5 Electrochemical measurements Electrochemical experiments were carried out in the conventional three-electrode cell with a platinum counter electrode (CE) and a saturated calomel electrode (SCE) coupled to a fine Luggin capillary as the reference electrode. In order to minimize ohmic contribution, the Luggin capillary was kept close to working electrode (WE) which was in the form of a square CRS embedded in PVC holder using epoxy resin so that the flat surface was only surface in the electrode. The WE surface area was 1.0 × 1.0 cm, abraded with emery paper (grade 320–500–800) on test face, rinsed with distilled water, degreased with acetone, and dried with a cold air stream. Before measurement the electrode was immersed in test solution at open circuit potential (OCP) for 2 h at 30 °C to be sufficient to attain a stable state. All electrochemical measurements were carried out using PARSTAT 2273 advanced electrochemical system (Princeton Applied Research). Each experiment was repeated at least three times to check the reproducibility. The potential of potentiodynamic polarization curves was started from a potential of −250 to +250 mV versus OCP at a sweep rate of 0.5 mV s −1 . Inhibition efficiency ( E p %) is defined as: (3) E p % = I corr - I corr(inh) I corr × 100 where I corr and I corr(inh) represent corrosion current density values without and with inhibitor, respectively. Electrochemical impedance spectroscopy (EIS) was carried out at OCP in the frequency range of 10 mHz–100 kHz using a 10 mV peak-to-peak voltage excitation. Inhibition efficiency ( E R %) is calculated on the basis of the equation: (4) E R % = R t(inh) - R t ( 0 ) R t(inh) × 100 where R t(0) and R t(inh) are charge transfer resistance values in the absence and presence of inhibitor, respectively. 3 Results and discussion 3.1 Weight loss measurements 3.1.1 Effect of TBTB concentration on corrosion rate The weight loss method of monitoring corrosion rate and inhibition efficiency is useful because of its simple application and reliability [66] . For the present study, the reproducibility of results obtained for both corrosion rate and percentage inhibition efficiency values for triplicate determination was very precise (within range of ±5%). Fig. 2 shows the corrosion rate ( v ) values of CRS with different concentrations of TBTB in both 1.0 M HCl and 0.5 M H 2 SO 4 solutions at 30 °C. In both acidic media, v decreases noticeably with an increase in TBTB concentration, i.e. the corrosion inhibition enhances with the inhibitor concentration. In the presence of 0.5 mM TBTB, the corrosion rate values are decreased to 0.53 and 2.00 g m −2 h −1 in 1.0 M HCl and 0.5 M H 2 SO 4 solutions, respectively. This behavior is due to the fact that the adsorption amount and coverage of inhibitor on CRS surface increase with the inhibitor concentration [67] . It should be noted that when the inhibitor concentration reaches about 0.20 mM, the corrosion rate value reaches certain data and does not change markedly. At any given inhibitor concentration, the corrosion rate in 0.5 M H 2 SO 4 is comparatively higher than that in 1.0 M HCl solution. 3.1.2 Effect of TBTB concentration on inhibition efficiency The values of inhibition efficiency obtained from the weight loss ( E w ) for different inhibitor concentrations in 1.0 M HCl and 0.5 M H 2 SO 4 solutions at 30 °C are shown in Fig. 3 . When the concentration of TBTB is less than 0.20 mM, E w increases sharply with an increase in concentration, while a further increase causes no appreciable change in performance. The maximum E w values are 95.1% (1.0 M HCl) and 88.2% (0.5 M H 2 SO 4 ) at 0.50 mM (5.0 × 10 −4 M), and at 0.25 mM (2.5 × 10 −3 M) concentration E w values are higher than 90% in HCl, and 80% in H 2 SO 4 , respectively, which indicates that TBTB is a very good inhibitor for steel in both acids. At the same inhibitor concentration, E w values follow the order: E w (1.0 M HCl) > E w (0.5 M H 2 SO 4 ). Under similar conditions, the inhibition efficiency obtained by weight loss measurements for 1-phenyl-5-mercapto-1,2,3,4-tetrazole (PMT) is 34.8% at 5.0 × 10 −4 M in 1.0 M HCl [60] ; for 5-mercapto-1-tetrazoleacetic sodium salt (MTAc), 69% at 200 mg l −1 (about 1.1 × 10 −3 M) in 1.0 M H 2 SO 4 [62] ; and for red tetrazolium (RT), 93.0% in 1.0 M HCl [63] and 52.5% in 1.0 M H 2 SO 4 [64] at 200 mg l −1 (about 6.0 × 10 −4 M). Therefore, comparing with PMT, MTAc and RT studied, TBTB shows better inhibition performance. This result could be explained as follows: the main adsorption centre of tetrazole derivative is tetrazole ring [60–65] . PMT, MTAc or RT has only one tetrazole ring, while TBTB contains not only one tetrazole ring but also one thiazole ring, which favors more adsorption of TBTB and improves the inhibitive ability. Furthermore, the molecular weight of TBTB is 414.32 g mol −1 , which is higher than that of PMT (178.21 g mol −1 ), MTAc (182.14 g mol −1 ) or RT (334.81 g mol −1 ), and likely to efficiently cover more surface area (due to adsorption) of metal. 3.1.3 Adsorption isotherm and standard adsorption free energy Basic information on the interaction between the inhibitor and CRS surface can be provided by the adsorption isotherm. Attempts were made to fit experimental data to various isotherms including Frumkin, Langmuir, Temkin, Freundlich, Bockris-Swinkels, and Flory–Huggins isotherms. By far the results were best fitted by Langmuir adsorption isotherm equation [64] : (5) c θ = 1 K + c where c is the concentration of inhibitor, K the adsorptive equilibrium constant, and θ is the surface coverage calculated as follows [64] : (6) θ = v 0 - v v 0 Plots of c/θ against c yield straight lines as shown in Fig. 4 , and the linear regression parameters are listed in Table 1 . Both linear correlation coefficient ( r ) and slope are very close to 1, indicating the adsorption of TBTB on steel surface obeys the Langmuir adsorption isotherm in 1.0 M HCl or 0.5 M H 2 SO 4 solution. Table 1 also shows that K of 1.0 M HCl is higher than that of 0.5 M H 2 SO 4 , which indicates that TBTB exhibits a stronger tendency to adsorb on steel surface in 1.0 M HCl solution. The adsorptive equilibrium constant ( K ) is related to the standard free energy of adsorption (Δ G 0 ) as shown the following equation [68] : (7) K = 1 55.5 exp ( - Δ G 0 RT ) where R is the gas constant (8.314 J K −1 mol −1 ), T the absolute temperature (K), and the value 55.5 is the concentration of water in solution expressed in M [68] . The Δ G 0 values are also listed in Table 1 . The negative values of Δ G 0 indicate that the adsorption of inhibitor molecule on steel surface is a spontaneous process. Generally, values of Δ G 0 up to −20 kJ mol −1 are consistent with the electrostatic interaction between the charged molecules and the charged metal (physical adsorption) while those more negative than −40 kJ mol −1 involve sharing or transfer of electrons from the inhibitor molecules to the metal surface to form a co-ordinate type of bond (chemisorption) [12,61,69] . In the present study, the value of Δ G 0 is found to be within the range −40 to −20 kJ mol −1 ; probably means that the adsorption of TBTB on CRS surface involves both physical adsorption and chemical adsorption. 3.2 Potentiodynamic polarization curves Potentiodynamic polarization curves for CRS in 1.0 M HCl and 0.5 M H 2 SO 4 solutions containing various concentrations of TBTB at 30 °C are shown in Figs. 5 and 6 (immersion time is 2 h), respectively. In both acid solutions, addition of TBTB causes a remarkable decrease in the corrosion rate i.e., shifts the both anodic and cathodic curves to lower current densities. In other words, both cathodic and anodic reactions of CRS electrode are drastically inhibited by TBTB. This may be ascribed to adsorption of inhibitor over the corroded surface [70] . The electrochemical corrosion parameters including corrosion current densities ( I corr ), corrosion potential ( E corr ), cathodic Tafel slope ( b c ), anodic Tafel slope ( b a ), and inhibition efficiency ( E P ) are presented in Table 2 . It is apparent that I corr decreases considerably in the presence of TBTB inhibitor, and decreases with increasing the inhibitor concentration. Correspondingly, E p increases with the inhibitor concentration, due to the increase in the blocked fraction of the electrode surface by adsorption. E p of 0.50 mM TBTB reaches up to a maximum of 93.8% in 1.0 M HCl; and 90.7% in 0.5 M H 2 SO 4 . In 1.0 M HCl solution, the presence of TBTB does not change the E corr , which indicates TBTB acts as a mixed-type inhibitor, and the inhibition of TBTB on CRS is caused by geometric blocking effect [71] . In other words, the inhibition effect comes from the reduction of the reaction area on the surface of the corroding metal [71] . On the other hand, in 0.5 M H 2 SO 4 solution, E corr shifts to positive, which indicates that inhibitor molecules are more adsorbed on the anodic sites resulting in an inhibition of the anodic reactions. Generally, if the displacement in E corr is >85 mV with respect to E corr in uninhibited solution, the inhibitor can be seen as a cathodic or anodic type [12,64] . In our study the maximum displacement is 46.6 mV, which indicates that TBTB can be arranged as a mixed-type inhibitor. The similar results were also reported with red tetrazolium (RT) for steel in H 2 SO 4 media [64] . In the presence of TBTB inhibitor, the slight change of both b c and b a in both acid solutions indicates that the corrosion mechanism of steel does not change. Furthermore, the inhibition efficiencies obtained from weight loss, electrochemical polarization curves are in reasonable good agreement. Namely, TBTB is a good inhibitor in both acid solutions, and inhibition efficiency in 1.0 M HCl is higher than that in 0.5 M H 2 SO 4 solution. 3.3 Electrochemical impedance spectroscopy (EIS) Figs. 7 and 8 show the Nyquist diagrams for CRS in 1.0 M HCl and 0.5 M H 2 SO 4 at 30 °C, respectively. In 1.0 M HCl solution, the impedance spectra exhibit one single depressed semicircle, which indicates that the corrosion of steel is mainly controlled by a charge transfer process. In contrast, in 0.5 M H 2 SO 4 solution, the impedance spectra consist of large capacitive loop at high frequencies followed by a small inductive loop at low frequency values. The high frequency capacitive loop is usually related to the charge transfer of the corrosion process and double layer behavior. On the other hand, the low frequency inductive loop may be attributed to the relaxation process obtained by adsorption species like FeSO 4 [72] or inhibitor species [73] on the electrode surface. It might be also attributed to the re-dissolution of the passivated surface at low frequencies [73] . In both acid solutions, comparing with blank solution, the shape is maintained throughout all tested concentrations, indicating that almost no change in the corrosion mechanism occurs due to the inhibitor addition [74] . These capacitive loops in both acid solutions are not perfect semicircles which can be attributed to the frequency dispersion effect as a result of the roughness and inhomogeneous of electrode surface [75] . Furthermore, the diameter of the capacitive loop in the presence of inhibitor is bigger than that in the absence of inhibitor (blank solution) and increases with the inhibitor concentration. This indicates that the impedance of inhibited substrate increases with the TBTB concentration. The EIS results of these capacitive loops are simulated by the equivalent circuit shown in Fig. 9 to pure electric models that could verify or rule out mechanistic models and enable the calculation of numerical values corresponding to the physical and/or chemical properties of the electrochemical system under investigation [76] . The circuit employed allows the identification of both solution resistance ( R s ) and charge transfer resistance ( R t ). It is worth mentioning that the double layer capacitance ( C dl ) value is affected by imperfections of the surface, and that this effect is simulated via a constant phase element (CPE) [77] . The CPE is composed of a component Q dl and a coefficient a. The parameter a quantifies different physical phenomena like surface inhomogeneousness resulting from surface roughness, inhibitor adsorption, porous layer formation, etc. Therefore, the capacitance is deduced from the following relation [72] : (8) C dl = Q dl × ( 2 π f max ) a - 1 where f max represents the frequency at which imaginary value reaches a maximum on the Nyquist plot. The electrochemical parameters of R t , C dl and E R are calculated by ZSimpWin software and presented in Table 3 . Inspection of Table 3 reveals that R t value increases prominently while C dl reduces with the concentration of TBTB in both acid media. The greatest effect was observed at 0.50 mM of TBTB which gives R t value of 418.6 Ωcm 2 in 1.0 M HCl, and 96.9 Ωcm 2 in 0.5 M H 2 SO 4 ; C dl value of 84.1 μF cm −2 in 1.0 M HCl, and 169.2 μF cm −2 in 0.5 M H 2 SO 4 . A large charge transfer resistance is associated with a slower corroding system. In contrast, better protection provided by an inhibitor can be associated with a decrease in capacitance of the metal. According to Helmholtz model [78] : (9) C dl = ε 0 ε d A where ε 0 is the permittivity of air, ε the local dielectric constant, d the thickness of the film and A is the surface area of the electrode. Therefore, the decrease in C dl in comparing with that in blank solution (without inhibitor), which can result from a decrease in local dielectric constant and/or an increase in the thickness of the electrical double layer, suggests that the inhibitor molecules function by adsorption at the metal/solution interface [72] . E R increases with the concentration of TBTB, and follows the order: E R (HCl) > E R (H 2 SO 4 ). The maximum E R values are 94.9% and 91.3% in 1.0 M HCl and 0.5 M H 2 SO 4 , respectively. These results again confirm that TBTB exhibits good inhibitive performance for CRS in both acid solutions, and it is more efficient to inhibit the corrosion of steel in 1.0 M HCl than 0.5 M H 2 SO 4 . Inhibition efficiencies obtained from weight loss ( E w ), potentiodynamic polarization curves ( E p ) and EIS ( E R ) are in good reasonably agreement. 3.4 Explanation for inhibition The inhibition mechanism can be proposed from the adsorption of inhibitor on steel surface. It is well known that the adsorption of inhibitor on steel/solution interface is affected by the chemical structures of the inhibitors, the nature and charged surface of the metal and the distribution of charge over the whole inhibitor molecule. In general, owing to the complex nature of adsorption and inhibition of a given inhibitor, it is impossible for single adsorption mode between inhibitor and metal surface. In the present system, based on the chemical structure of TBTB, TBTB has many active sites for the adsorption process. Thus, five types of adsorption may take place in the inhibiting phenomena involving TBTB molecules on steel surface as follows: (i) TBTB can be classified as an electrolyte, namely, the organic part (TBTB + ) is the cation and the inorganic part (Br − ) is the anion: (10) TBTB → TBT + + Br - Owing to neutral N and S atoms in TBT + , TBT + could further be protonated in the acid solution as following: (11) TBT + + x H + ↔ [ TBTH x ] ( x + 1 ) + Thus, in aqueous acidic solutions, the TBTB exists as protonated cations of TBT + and [TBTH x ] (x+1)+ . The charge of the metal surface can be determined from the value of E corr – E q=0 (zero charge potential) [78] . The E q=0 of iron is −530 mV vs. SCE in HCl [79] , and −550 mV vs. SCE in H 2 SO 4 [80] . In the present system, the values of E corr obtained in 1.0 M HCl and 0.5 M H 2 SO 4 are −447 mV vs. SCE and −507 mV vs. SCE, respectively. So the steel surface charges positive charge in both HCl and H 2 SO 4 solutions because of E corr – E q=0 (zero charge potential) > 0. Since the anions of Cl − , SO 4 2 - and Br − (produced as a result of the reaction (10)) could be specifically adsorbed, they create an excess negative charge towards the solution and favor more adsorption of the cations [49] , TBT + and [TBTH x ] (x+1)+ may adsorb on the negatively charged metal surface. In other words, there may be a synergism between anions (Cl − , SO 4 2 - and Br − ) and protonated inhibitor. It is generally accepted that Cl − ions have stronger tendency to adsorb do SO 4 2 - ions [81] , and the electrostatic influence on the inhibitor adsorption may be the reason for an increased protective effect in halide-containing solution [82] . Moreover, the lesser interference by SO 4 2 - ions with the adsorbed protonated cations may lead to lower adsorption and inhibition of acid corrosion [83] . So, the adsorption of TBTB on the steel surface is greater from 1.0 M HCl solution, which leads to better inhibition performance than that in 0.5 M H 2 SO 4 . (ii) Besides to the physical adsorption, TBT + and [TBTH x ] (x+1)+ may be adsorbed on the metal surface via the chemisorption mechanism, involving to the coordinate bonds that may be formed between the lone electrons pairs of the unprotonated N and S atoms and the empty orbitals of Fe atoms which enhanced the combination intension between the inhibitor molecule and electrode surface. (iii) It should be noted that the molecular structure of TBT + and [TBTH x ] (x+1)+ remains unchanged with respect to TBTB, that is, both N and S atoms on the ring remaining strongly blocked. TBT + and [TBTH x ] (x+1)+ have plentiful π-electrons owing to aromatic rings, they can be also adsorbed on the metal surface on the basis of donor–acceptor interactions between π-electrons of the heterocycles (tetrazole and thiazole ring) and vacant d-orbitals of Fe. The simultaneous adsorption of the tetrazole and thiazole rings induces greater adsorption greater adsorption of the inhibitor molecules onto the surface of cold rolled steel. The larger molecule area plays an important role in retarding the corrosion [84] . (iv) Due to the chelating action of tetrazole ring or thiazole ring, some metal complexes of Fe 2+ —tetrazole compounds [85,86] or Fe 2+ —thiazole compounds [87,88] have been widely prepared. Thus, TBT + and [TBTH x ] (x+1)+ may combine with freshly generated Fe 2+ ions on steel surface forming metal inhibitor complexes: (12) Fe → Fe 2 + + 2 e (13) TBT + + Fe 2 + ↔ [ TBT Fe ] 3 + (14) [ TBTH x ] ( x + 1 ) + + Fe 2 + ↔ [ TBTH x Fe ] ( x + 3 ) + These complexes might get adsorbed onto steel surface by the van der Waals force to form a blocking barrier to keep CRS from corrosion. (v) A combination of the above. 4 Conclusions (1) TBTB acts as a good inhibitor for the corrosion of CRS in 1.0 M HCl and 0.5 M H 2 SO 4 solutions. Inhibition efficiency ( E w ) increases with the inhibitor concentration, and the maximum E w values are 95.1% (1.0 M HCl) and 88.2% (0.5 M H 2 SO 4 ) at 0.50 mM (5.0 × 10 −4 M). Inhibition performance in 1.0 M HCl is higher than that in 0.5 M H 2 SO 4 . (2) In both acid media, the adsorption of TBTB is a spontaneous process and obeys Langmuir adsorption isotherm. The parameter of adsorption free energy (Δ G 0 ) indicates that the adsorption of TBTB involves both physical adsorption and chemical adsorption. (3) TBTB acts as a mixed-type inhibitor in 1.0 M HCl and 0.5 M H 2 SO 4 , while prominently retards anodic reaction in 0.5 M H 2 SO 4 . (4) EIS spectra exhibit one capacitive loop in 1.0 M HCl, while one large capacitive loop at high frequencies followed by a small inductive loop at low frequency values in 0.5 M H 2 SO 4 . The presence of TBTB in both acid solutions enhances R t values while reduces C dl values. (5) The adsorption of TBTB involves electrostatic attraction between anions (Cl − , SO 4 2 - ) and protonated inhibitor molecules, sharing electrons between the N, S atoms and Fe, donor–acceptor interactions between π-electrons of aromatic rings and vacant d-orbitals of Fe ,adsorption of the complexes of [TBT-Fe] 3+ and [TBTH x -Fe] (x+3)+ . Acknowledgements This study was carried out in the scope of research project funded by Key Laboratory for Forest Resources Conservation and Use in the Southwest Mountains of China (Southwest Forestry University) Ministry of Education , Key Construction Course of Chemical Engineering for Forest Products of Southwest Forestry University ( XKX200907 ), Natural Science Foundations of Southwest Forestry University ( 200715M ) and Educational Department of Yunnan Province ( 09C0181 ). The electrochemical measurements were carried out using PARSTAT 2273 advanced electrochemical system (Princeton Applied Research) provided by Advanced Science Instrument Sharing Center of Southwest Forestry University. References [1] G. Trabanelli Inhibitors an old remedy for a new challenge Corrosion 47 1991 410 419 [2] F. Bentiss M. Traisnel L. Gengembre M. Lagrenée Inhibition of acidic corrosion of mild steel by 3, 5-diphenyl-4H–1, 2, 4-triazole Appl. Surf. Sci. 161 2000 194 202 [3] J. Cruz R. Martínez J. Genesca E. García-Ochoa Experimental and theoretical study of 1-(2-ethylamino)-2-methylimidazoline as an inhibitor of carbon steel corrosion in acid media J. Electroanal. Chem. 566 2004 111 121 [4] M.H. Wahdan G.K. Gomma Effect of copper cation on electrochemical behaviour of steel in presence of imidazole in acid medium Mater. Chem. Phys. 47 1997 176 183 [5] G. Bereket E. Hür C. Öğretir Quantum chemical studies on some imidazole derivatives as corrosion inhibitors for iron in acidic medium J. Mol. Struct. (Theochem) 578 2002 79 88 [6] A.M.S. Abdennaby A.I. Abdulhady S.T. Abu-Oribi H. Saricimen The inhibition action of 1 (benzyl)1-H-4,5-dibenzoyl-1,2,3-triazole on mild steel in hydrochloric acid media Corros. Sci. 38 1996 1791 1800 [7] S.L. Granese B.M. Rosales C. Oviedo J.O. Zerbino The inhibition action of heterocyclic nitrogen organic compounds on Fe and steel in HCl media Corros. Sci. 33 1992 1439 1453 [8] F. Bentiss M. Traisnel L. Gengembre M. Lagrenée A new triazole derivative as inhibitor of the acid corrosion of mild steel: electrochemical studies, weight loss determination, SEM and XPS Appl. Surf. Sci. 152 1999 237 249 [9] L. Wang Inhibition of mild steel corrosion in phosphoric acid solution by triazole derivatives Corros. Sci. 48 2006 608 616 [10] M.A. Quraishi H.K. Sharma 4-Amino-3-butyl-5-mercapto-1,2,4-triazole: a new corrosion inhibitor for mild steel in sulphuric acid Mater. Chem. Phys. 78 2002 18 21 [11] E. García-Ochoa J. Genesca Understanding the inhibiting properties of 3-amino-1,2,4-triazole from fractal analysis Surf. Coat. Tech. 184 2004 322 330 [12] W.H. Li Q. He S.T. Zhang C.L. Pei B.R. Hou Some new triazole derivatives as inhibitors for mild steel corrosion in acidic medium J. Appl. Electrochem. 38 2008 289 295 [13] H.L. Wang R.B. Liu J. Xin Inhibiting effects of some mercapto-triazole derivatives on the corrosion of mild steel in 1.0 M HCl medium Corros. Sci. 46 2004 2455 2466 [14] F. Bentiss M. Traisnel H. Vezin M. Lagrenée Linear resistance model of the inhibition mechanism of steel in HCl by triazole and oxadiazole derivatives: structure–activity correlations Corros. Sci. 45 2003 371 380 [15] M. Lebrini M. Traisnel M. Lagrenée B. Mernari F. Bentiss Inhibitive properties, adsorption and a theoretical study of 3, 5-bis(n-pyridyl)-4-amino-1, 2, 4-triazoles as corrosion inhibitors for mild steel in perchloric acid Corros. Sci. 50 2008 473 479 [16] F. Bentiss M. Lagrenee M. Traisnel J.C. Hornez The corrosion inhibition of mild steel in acidic media by a new triazole derivative Corros. Sci. 41 1999 789 803 [17] W.H. Li X. Zhao F.Q. Liu B.R. Hou Investigation on inhibition behavior of S-triazole–triazole derivatives in acidic solution Corros. Sci. 50 2008 3261 3266 [18] F. Bentiss C. Jama B. Mernari H. El Attari L. El Kadi M. Lebrini M. Traisnel M. Lagrenée Corrosion control of mild steel using 3,5-bis(4-methoxyphenyl)-4-amino-1,2,4-triazole in normal hydrochloric acid medium Corros. Sci. 51 2009 1628 1635 [19] Z.H. Tao S.T. Zhang W.H. Li B.R. Hou Corrosion inhibition of mild steel in acidic solution by some oxo-triazole derivatives Corros. Sci. 51 2009 2588 2595 [20] R.M. Hudson T.J. Bulter C.J. Warning The effect of pyrrole-halide mixtures in inhibiting the dissolution of low-carbon steel in sulphuric acid Corros. Sci. 17 1977 571 581 [21] M. Bouklah A. Ouassini B. Hammouti A. El Idrissi The effect of pyrrole-halide mixtures in inhibiting the dissolution of low-carbon steel in sulphuric acid Appl. Surf. Sci. 250 2005 50 56 [22] M. Lashkari M.R. Arshadi DFT studies of pyridine corrosion inhibitors in electrical double layer: solvent, substrate, and electric field effects Chem. Phys. 299 2004 131 137 [23] M.A. Veloz I.G. Martinz Effect of some pyridine derivatives on the corrosion behavior of carbon steel in an environmental like NACE TM0177 Corrosion 62 2006 283 292 [24] A. Ouchrif M. Zegmout B. Hammouti S. El-Kadiri A. Ramdani 1,3-Bis(3-hyroxymethyl-5-methyl-1-pyrazole) propane as corrosion inhibitor for steel in 0.5 M H 2 SO 4 solution Appl. Surf. Sci. 252 2005 339 344 [25] G.K. Gomma Corrosion of low-carbon steel in sulphuric acid solution in the presence of pyrazole-halides mixture Mater. Chem. Phys. 55 1998 241 246 [26] M. Abdallah M.M. El-Naggar Cu +2 cation + 3,5-dimethyl pyrazole mixture as a corrosion inhibitor for carbon steel in sulfuric acid solution Mater. Chem. Phys. 71 2001 291 298 [27] M. Abdallah Corrosion behaviour of 304 stainless steel in sulphuric acid solutions and its inhibition by some substituted pyrazolones Mater. Chem. Phys. 82 2003 786 792 [28] A. Chetouani B. Hammouti T. Benhadda M. Daoudi Inhibitive action of bipyrazolic type organic compounds towards corrosion of pure iron in acidic media Appl. Surf. Sci. 249 2005 375 385 [29] M. Elayyachy M. Elkodadi A. Aouniti A. Ramdani B. Hammouti F. Malek A. Elidrissi New bipyrazole derivatives as corrosion inhibitors for steel in hydrochloric acid solutions Mater. Chem. Phys. 93 2005 281 285 [30] K. Tebbji A. Aouniti M. Benkaddour H. Oudda I. Bouabdallah B. Hammouti A. Ramdani New bipyrazolic derivatives as corrosion inhibitors of steel in 1 M HCl Prog. Org. Coat. 54 2005 170 174 [31] S.A. Abd El-Maksoud The influence of some arylazobenzoyl acetonitrile derivatives on the behaviour of carbon steel in acidic media Appl. Surf. Sci. 206 2003 129 136 [32] A. Chetouani A. Aouniti B. Hammouti N. Benchat T. Benhadda S. Kertit Corrosion inhibitors for iron in hydrochloride acid solution by newly synthesised pyridazine derivatives Corros. Sci. 45 2003 1675 1684 [33] G. Moretti G. Quartarone A. Tassan A. Zingales 5-amino and 5-chloro-indole as mild steel corrosion inhibitors in 1N sulphuric acid Electrochim. Acta 41 1996 1971 1980 [34] M. Düdükcü B. Yazici M. Erbil The effect of indole on the corrosion behaviour of stainless steel Mater. Chem. Phys. 87 2004 138 141 [35] A.A. Ismail S.H. Sanad A.A. El-Meligi Inhibiting effect of indole and some of its derivatives on corrosion of C-steel in HCl J. Mater. Sci. Technol. 16 2000 397 400 [36] L. Wang Evaluation of 2-mercaptobenzimidazole as corrosion inhibitor for mild steel in phosphoric acid Corros. Sci. 43 2001 2281 2289 [37] A. Popova M. Christov T. Deligeorigiev Influence of the Molecular Structure on the inhibitor properties of benzimidazole derivatives on mild steel corrosion in 1 M hydrochloric acid Corrosion 59 2003 756 764 [38] A. Popova M. Christov S. Raicheva E. Sokolova Adsorption and inhibitive properties of benzimidazole derivatives in acid mild steel corrosion Corros. Sci. 46 2004 1333 1350 [39] K.F. Khaled The inhibition of benzimidazole derivatives on corrosion of iron in 1 M HCl solutions Electrochim. Acta 48 2003 2493 2503 [40] M.H. Wahdan The synergistic inhibition effect and thermodynamic properties of 2-mercaptobenzimidazol and some selected cations as a mixed inhibitor for pickling of mild steel in acid solution Mater. Chem. Phys. 49 1997 135 140 [41] L.B. Tang X.M. Li Y.S. Si G.N. Mu G.H. Liu The synergistic inhibition between 8-hydroxyquinoline and chloride ion for the corrosion of cold rolled steel in 0.5 M sulfuric acid Mater. Chem. Phys. 95 2006 29 38 [42] Y. Yan W.H. Li L.K. Cai B.R. Hou Electrochemical and quantum chemical study of purines as corrosion inhibitors for mild steel in 1 M HCl solution Electrochim. Acta 53 2008 5953 5960 [43] X.H. Li S.D. Deng H. Fu Adsorption and inhibition of 6-benzylaminopurine on cold rolled steel in 1.0 M HCl Electrochim. Acta 54 2009 4089 4098 [44] X.H. Li S.D. Deng H. Fu G.N. Mu Inhibition effect of 6-benzylaminopurine on the corrosion of cold rolled steel in H 2 SO 4 solution Corros. Sci. 51 2009 620 634 [45] S.A. Ali M.T. Saeed S.U. Rahman The isoxazolidines: a new class of corrosion inhibitors of mild steel in acidic medium Corros. Sci. 45 2003 253 266 [46] S.A. Ali H.A. Al-Muallem M.T. Saeed S.U. Rahman Hydrophobic-tailed bicycloisoxazodidines: A comparative study of the newly synthesized compounds on the inhibition of mild steel corrosion in hydrochloric and sulfuric acid media Corros. Sci. 50 2008 664 675 [47] E.E. Foad El Sherbini Sulphamethoxazole as an effective inhibitor for the corrosion of mild steel in 1.0 M HCl solution Mater. Chem. Phys. 61 1999 223 228 [48] S.A.M. Refaey F. Taha A.M. Abd El-Malak Inhibition of stainless steel pitting corrosion in acidic medium by 2-mercaptobenzoxazole Appl. Surf. Sci. 236 2004 175 185 [49] F. Bentiss M. Traisnel M. Lagrenée The substituted 1,3,4-oxadiazoles: a new class of corrosion inhibitors of mild steel in acidic media Corros. Sci. 42 2000 127 146 [50] F. Bentiss M. Traisnel N. Chaibi B. Mernari H. Vezin M. Lagrenée 2,5-Bis(n-methoxyphenyl)-1,3,4-oxadiazoles used as corrosion inhibitors in acidic media: correlation between inhibition efficiency and chemical structure Corros. Sci. 44 2002 2271 2289 [51] M. Bouklah B. Hammouti M. Lagrenée F. Bentiss Thermodynamic properties of 2,5-bis(4-methoxyphenyl)-1,3,4-oxadiazole as a corrosion inhibitor for mild steel in normal sulfuric acid medium Corros. Sci. 48 2006 2831 2842 [52] F. Bentiss M. Traisnel H. Vezin H.F. Hildebrand M. Lagrenée 2,5-Bis(4-dimethylaminophenyl)-1,3,4-oxadiazole and 2,5-bis(4-dimethylaminophenyl)-1,3,4-thiadiazole as corrosion inhibitors for mild steel in acidic media Corros. Sci. 46 2004 2781 2792 [53] M. El Azhar B. Mernari M. Traisnel F. Bentiss M. Lagrenée Corrosion inhibition of mild steel by the new class of inhibitors [2,5-bis(n-pyvidyl)-1,3,4-thiadiazoles] in acid Corros. Sci. 43 2001 2229 2238 [54] F. Bentiss M. Lebrini H. Vezin M. Lagrenée Experimental and theoretical study of 3-pyridyl-substituted 1,2,4-thiadiazole and 1,3,4-thiadiazole as corrosion inhibitors of mild steel in acidic media Mater. Chem. Phys. 87 2004 18 23 [55] F. Bentiss M. Lebrini H. Vezin F. Chai M. Traisnel M. Lagrenée Enhanced corrosion resistance of carbon steel in normal sulfuric acid medium by some macrocyclic polyether compounds containing a 1,3,4-thiadiazole moiety: AC impedance and computational studies Corros. Sci. 51 2009 2165 2173 [56] A.K. Singh M.A. Quraishi The effect of some bis-thiadiazole derivatives on the corrosion of mild steel in hydrochloric acid Corros. Sci. 52 2010 1373 1385 [57] M.A. Quraishi H.K. Sharma Thiazoles as corrosion inhibitors for mild steel in formic and acetic acid solutions J. Appl. Electrochem. 35 2005 33 39 [58] H.Q. Lian R.Q. Liu L.Q. Zhu J.D. Wang Inhibition corrosion of thiazole derivatives on A3 steel in 1 mol/L HCl solution Chin. J. Appl. Chem. 23 2006 676 681 (in Chinese) [59] M.A. Quraishi M.A.W. Khan M. Ajmal S. Muralidharan S.V. Iyer Influence of heterocyclic anils on corrosion inhibition and hydrogen permeation through mild steel in acid chloride environments Corrosion 53 1997 475 480 [60] S. Kertit B. Hammouti Corrosion inhibition of iron 1 M HCl by 1-phenyl-5-mercapto-1,2,3,4-tetrazole Appl. Surf. Sci. 93 1996 59 66 [61] E. Bensajjay S. Alehyen M. El Achouri S. Kertit Corrosion inhibition of steel by 1-phenyl-5-mercapto 1, 2, 3, 4-tetrazole in acidic environments (0.5 M H2SO4 and 1/3 M H3PO4) Anti-Corros. Meth. Mater. 50 2003 402 409 [62] P. Morales-Gil G. Negrón-Silva M. Romero-Romoa C. Ángeles-Chávez M. Palomar-Pardavé Corrosion inhibition of pipeline steel grade API 5L X52 immersed in 1 M H 2 SO 4 aqueous solution using heterocyclic organic molecules Electrochim. Acta 49 2004 4733 4741 [63] X.H. Li S.D. Deng H. Fu Corrosion inhibition of red tetrazolium for cold rolled steel in hydrochloric acid media Chin. J. Appl. Chem. 26 2009 1075 1079 (in Chinese) [64] X.H. Li S.D. Deng H. Fu Synergism between red tetrazolium and uracil on the corrosion of cold rolled steel in H 2 SO 4 solution Corros. Sci. 51 2009 1344 1355 [65] X.H. Li S.D. Deng H. Fu Synergistic inhibition effect of red tetrazolium and uracil on the corrosion of cold rolled steel in H 3 PO 4 solution: weight loss, electrochemical, and AFM approaches Mater. Chem. Phys. 115 2009 815 824 [66] I.B. Obot N.O. Obi-Egbedi Adsorption properties and inhibition of mild steel corrosion in sulphuric acid solution by ketoconazole: experimental and theoretical investigation Corros. Sci. 52 2010 198 204 [67] X.H. Li G.N. Mu Tween-40 as corrosion inhibitor for cold rolled steel in sulphuric acid: weight loss study, electrochemical characterization, and AFM Appl. Surf. Sci. 252 2005 1254 1265 [68] E. Cano J.L. Polo A. La Iglesia J.M. Bastidas A study on the adsorption of benzotriazole on copper in hydrochloric acid using the inflection point of the isotherm Adsorption 10 2004 219 225 [69] F. Bentiss M. Lebrini M. Lagrenée Thermodynamic characterization of metal dissolution and inhibitor adsorption processes in mild steel/2,5-bis(n-thienyl)-1,3,4-thiadiazoles/hydrochloric acid system Corros. Sci. 47 2005 2915 2931 [70] G.N. Mu X.H. Li Q. Qu J. Zhou Molybdate and tungstate as corrosion inhibitors for cold rolling steel in hydrochloric acid solution Corros. Sci. 48 2006 445 459 [71] C. Cao On electrochemical techniques for interface inhibitor research Corros. Sci. 38 1996 2073 2082 [72] M. Lagrenée B. Mernari M. Bouanis M. Traisnel F. Bentiss Study of the mechanism and inhibiting efficiency of 3,5-bis(4-metylthiophenyl)-4H-1,2,4-triazole on mild steel corrosion in acidic media Corros. Sci. 44 2002 573 588 [73] A.K. Singh M.A. Quraishi Effect of cafazolin on the corrosion of mild steel in HCl solution Corros. Sci. 52 2010 152 160 [74] N. Labjar M. Lebrini F. Bentiss N.E. Chihib S. El Hajjaji C. Jama Corrosion inhibition of carbon steel and antibacterial properties of aminotris-(methylnephosnic) acid Mater. Chem. Phys. 119 2010 330 336 [75] M. Lebrini M. Lagrenée H. Vezin M. Traisnel F. Bentiss Experimental and theoretical study for corrosion inhibition of mild steel in normal hydrochloric acid solution by some new macrocyclic polyether compounds Corros. Sci. 49 2007 2254 2269 [76] A.R.S. Priya V.S. Muralidharam A. Subramania Development of novel acidizing inhibitors for carbon steel corrosion in 15% boiling hydrochloric acid Corrosion 64 2008 541 552 [77] P. Bommersbach C. Alemany-Dumont J.P. Millet B. Normand Hydrodynamic effect on the behaviour of a corrosion inhibitor film: characterization by electrochemical impedance spectroscopy Electrochim. Acta 51 2006 4011 4018 [78] D.P. Schweinsberg V. Ashworth The inhibition of the corrosion of pure iron in 0.5 M sulphuric acid by n -alkyl quaternary ammonium iodides Corros. Sci. 28 1988 539 545 [79] G. Banerjee S.N. Malhotra Contribution to adsorption of aromatic amines on mild steel surface from HCl solutions by impedance, UV, and Raman spectroscopy Corrosion 48 1992 10 15 [80] S.C. Roy S.K. Roy S.C. Sircar Critique of inhibitor evaluation by polarization measurement Br. Corro. J. 32 1988 102 104 [81] J.O.M. Bockris B. Yang Mechanism of corrosion inhibition of iron in acid solution by acetylenic alcohols J. Elecrochem. Soc. 135 1991 2237 2252 [82] M. Lebrini M. Lagrenée M. Traisnel L. Gengembre H. Vezin F. Bentiss Enhanced corrosion resistance of mild steel in normal sulfuric acid medium by 2, 5-bis(n-thienyl-1, 3, 4-thiadiazoles: electrochemical, X-ray photoelectron spectroscopy and theoretical studies Appl. Surf. Sci. 253 2007 9267 9276 [83] S. Rengamati S. Muralidharan M. Anbu Kulandainathan S. Venkatakrishna Iyer J. Appl. Electrochem. 24 1994 355 [84] A.K. Singh M.A. Quraishi Effect of 2,2′ benzothiazolyl disulfide on the corrosion of mild steel in acid media Corros. Sci. 51 2009 2752 2760 [85] A.F. Stassen E. Dova J. Ensling H. Schenk P. Gütlich J.G. Haasnoot J. Reedijk Spin crossover in hexakis(1-(2-chloroethyl)-tetrazole)iron(II) complexes; synthesis and magnetic properties Inorg. Chim. Acta 335 2002 61 68 [86] N. Hassan P. Weinberger F. Kubel G. Molnar A. Bousseksou L. Dlhan R. Boča W. Linert Two new Fe(II) spin crossover complexes with tetrazol-1-yl-cycloalkane ligands Inorg. Chim. Acta 362 2009 3629 3636 [87] M. James H. Kawaguchi K. Tatsumi Synthesis and crystal structure of a novel mixed valence tri-iron complex salt: [hexakis(thiazole)iron(II)][μ-oxo-bis(trichloroiron(III))] Polyhedron 16 1997 4279 4282 [88] L. Zhu K.L. Yao Z.L. Liu Theoretical studies on the spin distribution on the dihalide-bridged polymer metallic antiferromagnet Fe(thiazole) 2 Cl 2 Phys. Lett. A 353 2006 245 249

Abstract:Research highlights ► Acid violet 6B (AV6B) is found to be a good inhibitor for the corrosion of CRS in 1.0 M HCl. ► Effects of hydrochloric acid concentration (1.0 – 5.0 M) and immersion time (2 – 144 h) are discussed in detail. ► The corrosion inhibition is satisfactorily discussed by both thermodynamic and kinetic parameters. ► AV6B acts as a mixed-type inhibitor. ► The adsorption of AV6B obeys Langmuir adsorption isotherm. Abstract The inhibition effect of acid violet 6B (AV6B) on the corrosion of cold rolled steel (CRS) in 1.0–5.0 M HCl solution was studied for the first time by weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) methods. The results show that AV6B is a very good inhibitor in 1.0 M HCl, and the adsorption of AV6B on CRS surface obeys Langmuir adsorption isotherm. Polarization curves reveal that AV6B behaves as a mixed-type inhibitor. EIS spectra exhibit one capacitive loop and confirm the inhibitive ability. Effects of immersion time and acid concentration on inhibition performance were also discussed. Keywords A. Steel B. EIS B. Polarization B. Weight loss C. Acid inhibition 1 Introduction The use of inhibitors is one of the most practical methods for protecting materials against corrosion, especially in acidic media [1] . Acid solutions are widely used in industry, some of the important fields of application being acid pickling of iron and steel, chemical cleaning and processing, ore production and oil well acidification. As acidic media, the use of hydrochloric acid in pickling of metals, acidization of oil wells and in cleaning of scales is more economical, efficient and trouble-free, compared to other mineral acids. Because of the general aggression of acid solutions, inhibitors are commonly used to reduce the corrosive attack on metallic materials. Most well-known acid inhibitors are organic compounds containing nitrogen, sulfur, and oxygen atoms. The efficiency of these compounds mainly depends on their abilities to be adsorbed on the metal surface with the polar groups acting as the adsorptive centers. Among them, organic dyes whose molecules meet certain desirable characteristics as potential corrosion inhibitors, have received a considerable amount of attention. Up to now, various organic dyes have been used as corrosion inhibitors for steel in acid media (HCl, H 2 SO 4 , and H 3 PO 4 ), such as neutral red (NR) [2] , 1-(2-pyridylazo)-2-naphthol (PAN) [3] , indigo dye [4] , thymol blue [5] , congo red [6,7] , methylene blue [8,9] , methyl green [10] , crystal violet [11] , 8-quinolinol-5-azoantipyrine (HQAP) [12] , methyl red [13] , cresol red [14] , methyl orange [15] , alizarin yellow GG [16] , fast green [17] , methylene violet [18] and methyl violet [19] . It has been reported that the adsorption of organic dye takes place through N, O, S atoms in polar function groups, as well as those with triple or conjugated double bonds or aromatic rings in their molecular structures. The adsorption process is influenced by the chemical structures of the inhibitors, the nature and charged surface of the metal and the distribution of charge over the whole inhibitor molecule. Acid violet 6B (C 39 H 40 N 3 O 6 S 2 Na) is an organic dye with good solubility in water. Its molecules possess N, O, S atoms, which is a good potential inhibitor. However, to our best of knowledge, acid violet 6B (AV6B) has not yet been investigated as a corrosion inhibitor. In the present work, the inhibition effect of AV6B on the corrosion of cold rolled steel (CRS) in hydrochloric acid (HCl) solution was studied for the first time using weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) methods. The adsorption mode of AV6B on steel surface and the standard adsorption free energy (Δ G 0 ) were calculated and discussed. Meanwhile, effects of immersion time (2–144 h) and acid concentration (1.0–5.0 M) on corrosion inhibition were also investigated and discussed. A probable inhibitive mechanism is presented to explain the results. 2 Experimental 2.1 Materials Tests were performed on a cold rolled steel (CRS) of the following composition (wt.%): 0.05% C, 0.28% Mn, 0.023% P, 0.019% S, 0.02% Si, and the remainder Fe. 2.2 Inhibitor The organic dye of acid violet 6B (AV6B) was obtained from Shanghai Chemical Reagent Company of China. Fig. 1 shows the molecular structure of AV6B. Clearly, the molecule is big enough (molecular weight 733.87 g mol −1 ) to cover more surface area (due to adsorption) of the metal surface. 2.3 Solutions The aggressive solution of 1.0–5.0 M HCl was prepared by dilution of AR grade 37% HCl with distilled water. The concentration range employed for AV6B was 2–20 μM (2.0 × 10 −6 –2.0 × 10 −5 M). 2.4 Weight loss measurements The CRS sheets of 2.5 cm × 2.0 cm × 0.04 cm were abraded by a series of emery paper (grade 320–500–800) and then washed with distilled water, degreased with acetone, and finally dried at room temperature. After weighing accurately by OHAUS Adventure™ digital balance with sensitivity of ±0.1 mg, the specimens were immersed in beaker containing 250 ml 1.0 M HCl without and with different concentrations of AV6B using glass hooks and rods. The temperature was controlled at 30 ± 0.1 °C by a water thermostat. All the aggressive acid solutions were open to air. After immersion for 6 h, the specimens were taken out, washed with bristle brush under running water to remove the corrosion product, dried with a hot air stream, and re-weighed accurately. In order to get good reproducibility, experiments were carried out in triplicate. The average weight loss of three parallel CRS sheets was obtained. Then the experiments were repeated at different immersion time and hydrochloric acid concentration. The corrosion rate ( v ) is calculated by the following equation [20] : (1) v = W St where W is the average weight loss of three parallel CRS sheets, S the total area of one CRS specimen, and t is immersion time. With the corrosion rate calculated, the inhibition efficiency ( E w ) is determined as follows [20] : (2) E w % = v 0 - v v 0 × 100 where v 0 and v are the values of corrosion rate without and with inhibitor, respectively. 2.5 Electrochemical measurements Electrochemical experiments were carried out in the conventional three-electrode cell with a platinum counter electrode (CE) and a saturated calomel electrode (SCE) coupled to a fine Luggin capillary as the reference electrode. To minimize ohmic contribution, the Luggin capillary was placed close to working electrode (WE) which was in the form of a square CRS embedded in PVC holder using epoxy resin so that the flat surface was only surface in the electrode. The working surface area was 1.0 cm × 1.0 cm, abraded with emery paper (grade 320–500–800) on test face, rinsed with distilled water, degreased with acetone, and dried with a cold air stream. Before measurement the electrode was immersed in test solution at open circuit potential (OCP) for 2 h to be sufficient to attain a stable state. All electrochemical measurements were carried out at 30 °C using PARSTAT 2273 advanced electrochemical system (Princeton Applied Research). Each experiment was repeated at least three times to check the reproducibility. The potential of potentiodynamic polarization curves was increased at 0.5 mV s −1 and started from a potential of −250 mV to +250 mV versus open circuit potential (OCP vs. SCE). Inhibition efficiency ( E p %) is defined as: (3) E p % = I corr - I corr(inh) I corr × 100 where I corr and I corr(inh) represent corrosion current density values without and with inhibitor, respectively. Electrochemical impedance spectroscopy (EIS) was carried out at OCP in the frequency range of 10 mHz–100 kHz using a 10 mV peak-to-peak voltage excitation. Inhibition efficiency ( E R %) is defined as: (4) E R % = R t(inh) - R t ( 0 ) R t(inh) × 100 where R t(0) and R t(inh) are charge transfer resistance values in the absence and presence of inhibitor, respectively. 2.6 Fourier transform infrared spectroscopy (FTIR) FTIR spectra were recorded in an AVATAR-FTIR-360 spectrophotometer (Thermo Nicolet Company, USA). In order not to damage the adsorbed layer of the CRS surfaces after immersion in uninhibited and inhibited HCl solutions; the FTIR reflectance accessory was applied to measure the CRS surfaces [21] . 2.7 Scanning electron microscopy (SEM) Samples of dimension 2.5 cm × 2.0 cm × 0.06 cm were prepared as described above (Section 2.4). After immersion in 1.0 M HCl without and with 20 μM AV6B at 30 °C for 6 h, the specimens were thoroughly washed with distilled water, dried with a cold air blaster. SEM experiments were performed with Japan instrument model S-3000N scanning electron microscope (Hitachi High-Tech Science Systems Corporation). 3 Results and discussion 3.1 Weight loss measurements 3.1.1 Effect of AV6B concentration on inhibition efficiency The weight loss method of monitoring corrosion rate and inhibition efficiency is useful because of its simple application and reliability [22,23] . For the present study, the reproducibility of results obtained for both corrosion rate and percentage inhibition efficiency values for triplicate determination was very precise (within range of ±5%). Fig. 2 shows the corrosion rate ( v ) and inhibition efficiency ( E w ) values with different concentrations of AV6B in 1.0 M HCl solution at 30 °C (immersion time is 6 h). The corrosion rate ( v ) decreases noticeably with the increase in AV6B concentration from 10.08 to 0.77 g m −2 h −1 at 0 and 20 μM of AV6B, respectively, i.e., the corrosion inhibition enhances with the inhibitor concentration. This behavior is due to the fact that the adsorption coverage of inhibitor on CRS surface increases with the inhibitor concentration [24] . When the inhibitor concentration reaches about 10 μM, the corrosion rate (1.01 g m −2 h −1 ) does not change markedly with the inhibitor concentration. Fig. 2 also shows that when the concentration of AV6B is less than 10 μM, E w increases sharply with increase in concentration, while a further increase causes no appreciable change in performance. The maximum E w is 92.6% at 20 μM (2.0 × 10 −5 M) and the inhibition is estimated to be higher than 70% even at 2 μM (2.0 × 10 −6 M), and its protection is >90% at 10 μM (1.0 × 10 −5 M), which indicates that AV6B is a very good inhibitor for CRS in 1.0 M HCl. Under similar conditions of steel in 1.0 M HCl, the inhibition efficiency obtained by weight loss measurements for neutral red (NR) is 65.6% at 10 mg l −1 (about 3.5 × 10 −5 M) [2] ; for 1-(2-pyridylazo)-2-naphthol (PAN), 72.9% at 1.0 × 10 −5 M [3] ; for crystal violet, about 42% at 1.0 × 10 −5 M [4] ; for fast green, 72% at 2.0 × 10 −5 M [17] ; and for methyl violet, 87.2% at 20 μM [19] . Therefore, comparing with NR, PAN, crystal violet, fast green and methyl violet, AV6B shows better inhibition performance. Also, it should be noted that three tested organic dyes of crystal violet [4] , methyl violet [19] and acid violet 6B (AV6B) have similar chemical molecular skeleton structure, which implies that these series of organic dyes could be seemed as the good potential corrosion inhibitors for steel in hydrochloric acid solution. 3.1.2 Adsorption isotherm and standard adsorption free energy Basic information on the interaction between the inhibitor and CRS surface can be provided by the adsorption isotherm. Attempts were made to fit experimental data to various adsorption isotherms including Frumkin, Langmuir, Temkin, Freundlich, Bockris-Swinkels and Flory–Huggins isotherms. By far the results were best expressed by Langmuir adsorption isotherm equation [20,24] : (5) c θ = 1 K + c where c is the concentration of inhibitor, K the adsorptive equilibrium constant and θ is the surface coverage calculated by Sekine and Hirakawa’s method [25] : (6) θ = v 0 - v v 0 - v m where v m is the smallest corrosion rate. Plot of c / θ against c yields a straight line as shown in Fig. 3 . The linear correlation coefficient ( r ) is almost equal to 1 ( r = 0.9999) and the slope is very close to 1 (slope = 0.9655), indicating the adsorption of AV6B on steel surface obeys the Langmuir adsorption isotherm. The adsorptive equilibrium constant ( K ) calculated is 1.40 × 10 6 M −1 , which is related to the standard free energy of adsorption (Δ G 0 ) via [26] : (7) K = 1 55.5 exp - Δ G 0 RT where R is the gas constant (8.314 J K −1 mol −1 ), T the absolute temperature (K), the value 55.5 is the concentration of water in solution expressed in M [26] . The Δ G 0 value calculated is −45.79 kJ mol −1 . The high absolute value ofΔ G 0 indicates that it is more strongly adsorbed on the steel surface in 1.0 M HCl solution. Generally, values of Δ G 0 up to −20 kJ mol −1 are consistent with the electrostatic interaction between the charged molecules and the charged metal (physical adsorption) while those more negative than −40 kJ mol −1 involve sharing or transfer of electrons from the inhibitor molecules to the metal surface to form a co-ordinate type of bond (chemisorption) [26–29] . In the present study, the value of Δ G 0 is found to be negative than −40 kJ mol −1 ; means that the adsorption mechanism of AV6B on CRS surface is mainly the chemisorption. Noticeably, it is generally accepted that physical adsorption is preceding stage of chemisorption of inhibitor on metal surface [30] . In other words, chemisorption is always accompanied by physisorption [31] . Therefore, in the adsorption process of AV6B on steel surface, the adsorption will be further discussed in the last part of this work. 3.1.3 Effect of immersion time on inhibition efficiency The inhibition kinetics of corrosion inhibitor is another important role in assessing the stability of inhibitive behavior of inhibitors, so it is necessary to evaluate the inhibition efficiency of inhibitor for a long immersion time. In the present study, effect of immersion time (2–144 h) on corrosion inhibition of AV6B at 5, 10 and 20 μM in 1.0 M HCl at 30 °C was also studied although pickling is applied over this period not usually of time. Fig. 4 shows the effect of immersion time on the inhibition efficiency ( E w ). Inspection of Fig. 4 reveals that AV6B inhibits the corrosion of CRS for all immersion time at all concentrations, and E w increases with the inhibitor concentration. Furthermore, the changed rule of E w at each inhibitor concentration is good consistent. That is, E w increases with immersion time from 2 to 6 h, while remains constant in 6–48 h (84% at 5 μM, 91% at 10 μM, and 93% at 20 μM), then decreases with immersion time within range of 48–144 h. When the immersion time is up to 144 h, E w are 65.4%, 76.3% and 83.6% at 5, 10 and 20 μM, respectively. The reasons could be the adsorptive film of AV6B which is dependent on the immersion time [32,33] . First, the adsorptive film becomes more compact and uniform with the increase of immersion time (2–6 h). Then the adsorptive film becomes saturated state within 6–48 h, which causes inhibition performance is steady. However, when the immersion time is long (48–144 h), the adsorptive film is not more uniform and instability [34] or the desorption of adsorbed inhibitor [35] because of the corrosion of acid media. 3.1.4 Effect of hydrochloric acid concentration on corrosion inhibition In order to get further general information of the corrosion inhibition of AV6B, the effect of hydrochloric acid concentration (1.0–5.0 M) on corrosion inhibition was also studied. Fig. 5 shows the relationship between corrosion rate ( v ) and HCl concentration ( C ) at 30 °C (immersion time is 6 h). The corrosion rates obtained both in the absence and presence of AV6B increase with the increase of HCl concentration, and the corrosion rate is 41.20 g m −2 h −1 for blank (without inhibitor) in 5.0 M HCl. After adding AV6B inhibitor, the corrosion rate decreases with the increase of AV6B in the whole HCl concentration. To study the effect of acid concentration on the corrosion inhibition, assuming the corrosion rate ( v ) against the molar concentration of acid concentration obeys the expression proposed by Mathur and Vasudevan [36] : (8) ln v = ln k + BC where k is the rate constant, B the reaction constant and C is the molar concentration of HCl. Fig. 6 shows straight lines of ln v – C at different inhibitor concentration. The straight lines show that the kinetic parameters could be calculated by Eq. (8) , and listed in Table 1 . The linear regression coefficients ( r ) are very close to 1, which also confirms that there is a good linear relationship between natural logarithm of corrosion rate (ln v ) and acid concentration ( C ), namely, the corrosion of CRS in uninhibited and inhibited HCl supports the kinetic equation proposed by Mathur and Vasudevan. Eq. (8) shows that k can be regarded as a commencing rate at zero acid concentration, so k means the ability of corrosion of acid for steel [36] . Table 1 shows that k decreases to more extent after adding AV6B in HCl solution, and follows the order: k (20 μM) < k (10 μM) < k (5 μM), which confirms that the corrosion of steel is drastically inhibited by the AV6B inhibitor, and the inhibition enhances with the inhibitor concentration. According to Eq. (8) , B is the slope of the line of ln v – C , so B implies the changed extent of corrosion rate with the acid concentration. The value of B in inhibited HCl is higher than that in uninhibited HCl, which indicates that the changed extent of v with C in inhibited HCl is bigger than that in uninhibited HCl. Fig. 7 shows the relationship between inhibition efficiency obtained from weight loss method ( E w ) and the concentration of HCl ( C ) at 30 °C. At all inhibitor concentrations, increasing acid concentration resulted in decreasing E w . This is because of high aggressiveness with the increase of acid concentration [37] . The minimum E w values are 17.5%, 38.1% and 45.4% in 5.0 M HCl at 5, 10 and 20 μM, respectively. 3.2 Potentiodynamic polarization studies Potentiodynamic polarization curves for CRS in 1.0 M HCl without and with different concentrations of AV6B at 30 °C are shown in Fig. 8 (immersion time is 2 h). With respect to the blank, the presence of AV6B causes a prominent decrease in the corrosion rate, i.e., shifts both anodic and cathodic curves to lower values of current densities. Namely, both cathodic and anodic reactions of CRS electrode corrosion are drastically retarded by AV6B in 1.0 M HCl. Electrochemical parameters of corrosion current densities ( I corr ), corrosion potential ( E corr ), cathodic Tafel slope ( b c ), anodic Tafel slope ( b a ), and inhibition efficiency ( E p ) are presented in Table 2 . It shows that I corr decreases considerably in the presence of AV6B, and decreases with increasing the inhibitor concentration. Correspondingly, E p increases with the inhibitor concentration, and the maximum E p is up to 93.1% at 20 μM AV6B. The shift of E corr is negligible in the presence of AV6B, therefore, AV6B can be arranged as a mixed-type inhibitor, and the inhibition action is caused by geometric blocking effect [38] . Namely, the inhibition action comes from the reduction of the reaction area on the surface of the corroding metal [38] . Tafel slopes of b c and b a do not change upon addition of AV6B, which indicates that adding AV6B does not change the corrosion reaction mechanism of reduction of H + and anodic dissolution. 3.3 Electrochemical impedance spectroscopy (EIS) Fig. 9 shows the Nyquist diagrams for CRS in 1.0 M HCl at 30 °C without and with different concentrations of AV6B (immersion time s 2 h). These diagrams have similar shape throughout all tested concentrations, indicating that almost no change in the corrosion mechanism occurs due to the inhibitor addition [39] . The impedance spectrum exhibits one capacitive loop and only one time constant in the frequency range studied, which indicates that the corrosion of steel is mainly controlled by a charge transfer process. These capacitive loops are not perfect semicircles which can be attributed to the frequency dispersion effect as a result of the roughness and inhomogeneous of electrode surface [40] . Furthermore, the diameter of the capacitive loop in the presence of inhibitor is higher than that in blank solution (without inhibitor) and increases with the inhibitor concentration. This indicates that the impedance of inhibited substrate increases with AV6B concentration. The EIS results are simulated by the equivalent circuit shown in Fig. 10 to pure electric models that could verify or rule out mechanistic models and enable the calculation of numerical values corresponding to the physical and/or chemical properties of the electrochemical system under investigation [41] . The circuit employed allows the identification of both solution resistance ( R s ) and charge transfer resistance ( R t ). It is worth mentioning that the double layer capacitance ( C dl ) value is affected by imperfections of the surface, and that this effect is simulated via a constant phase element (CPE) [42] . The CPE is composed of a component Q dl and a coefficient a. The parameter a quantifies different physical phenomena like surface inhomogeneousness resulting from surface roughness, inhibitor adsorption, porous layer formation, etc. So the capacitance is deduced from the following relation [43] : (9) C dl = Q dl × ( 2 π f max ) a - 1 where f max represents the frequency at which imaginary value reaches a maximum on the Nyquist plot. The electrochemical parameters of R t , C dl and E R are calculated by ZSimpWin software and presented in Table 3 . Inspection of Table 3 reveals that R t values increases prominently while C dl reduces with the concentration of AV6B. A large charge transfer resistance is associated with a slower corroding system. In contrast, better protection provided by an inhibitor can be associated with a decrease in capacitance of the metal. The decrease in C dl comparing with that in blank solution (without inhibitor), which can result from a decrease in local dielectric constant and/or an increase in the thickness of the electrical double layer, suggests that the inhibitor molecules function by adsorption at the metal/solution interface [43] . E R increases with the concentration of AV6B, and the maximum E R reaches up to 93.1% at 20 μM, which further confirm AV6B exhibits very good inhibitive performance for CRS in 1.0 M HCl. Table 4 lists the values of inhibition efficiency ( E ) using different methods. It shows that E obtained from weight loss, potentiodynamic polarization curves and EIS are a little different owing to different conditions of three methods. The difference could be due to the discrepancy in the three experimental methods (the weight loss gives average E , but polarization curves and EIS give the instantaneous value). But the general rule of E obtained by three methods is similar. Namely, all three methods indicate that AV6B acts as a good inhibitor for CRS in 1.0 M HCl, and E increases with the inhibitor concentration. 3.4 Fourier transform infrared spectroscopy FTIR spectrometer is a powerful instrument that can be used to determine the type of bonding for organic inhibitors absorbed on the metal surface [21,44,45] . In this article, FTIR spectrometer is used to identify whether there is adsorption and to provide new bonding information on the steel surface after immersion in inhibited HCl solution. The FTIR reflectance spectrum of corrosion layer formed on the CRS surface after 6 h immersion in 1.0 M HCl is shown in Fig. 11 a. The weak bands at 3867 and 3724 cm −1 are assigned to Fe–O bending [44] , and the bands at 1324, 1065, 854, 793 and 711 cm −1 arise form FeOOH and Fe 2 O 3 [46] , which reveal the fact that the adsorbed protective film is oxidized by O 2 and H 2 O in air. The band at 3353 cm −1 is attributed to O–H stretching and 1630 cm −1 is for O–H bending, which further indicate the protective film contains H 2 O. Noticeably, due to the spectra in the experiment were obtained in the region from 650 to 4000 cm −1 , and FeCl 2 only has the typical bands in the 400–500 cm −1 region corresponding to the Fe–Cl bond, so the corrosion product of FeCl 2 cannot be detected by FTIR in this study. Fig. 11 b shows the FTIR spectrum of adsorbed protective layer formed CRS surface after immersion in 1.0 M HCl containing 20 μM AV6B. Fe–O bending bands are found at 3832 and 3785 cm −1 . The band at 3627 cm −1 which does not appear in Fig. 11 a may be assigned to Fe–N bending, which reveal the fact that AV6B can adsorb on the metal surface on the basis of donor–acceptor interactions between lone-pair electrons of N and the vacant d-orbital of Fe substrate. It is found that the N–H stretch at 3491 cm −1 , and O–H stretch at 3402 and 3333 cm −1 . The weak bands at 3272, 3210 and 3095 cm −1 can be attributed to C–H stretching vibration in benzene. The bands at 2931 and 2793 cm −1 are attributed to the aliphatic C–H asymmetric and symmetric stretching vibrations, respectively. The C N (or C C) stretching vibration at 1632 cm −1 further confirms that formation of the AV6B inhibitor adsorbed on steel surface. The absorption bands at 1563, 1516, 1440 and 1291 cm −1 is due to the framework vibration of benzene ring. The band at 1379 cm −1 is attributed to –CH 3 . Besides these, there are absorption bands at 1148 and 1044 cm −1 , which can be assigned to the C–N stretching vibration. The bands around or below 1000 cm −1 can be assigned to the C–H bending vibration in benzene. Comparing Fig. 11 a with b, it can be suggested that AV6B is absorbed on the CRS surface. 3.5 Scanning electron microscope (SEM) Fig. 12 shows the SEM photos of CRS surface in 1.0 M HCl. Fig. 12 a reveals that the CRS surface after immersion in uninhibited 1.0 M HCl shows an aggressive attack of the corroding medium on the steel surface. Moreover, the surface layer is very rough. In contrast, in the presence of AV6B, Fig. 12 b shows that there is much less damage on the steel surface, which clearly confirms the inhibition action. Also, there is an adsorbed film adsorbed on CRS surface, which does not exist in Fig. 12 a. In accordance, it can be concluded that the adsorption film can efficiently inhibits the corrosion of steel. 3.6 Explanation for inhibition Based on the chemical structure of AV6B, four kinds of adsorption may take place in the inhibiting phenomena involving AV6B molecules on steel surface as follows: (i) The main polar groups AV6B are N + , neutral N atom, –SO 3 Na and – SO 3 - . In acid solution, –SO 3 Na and – SO 3 - are in the form of: (10) – SO 3 Na → – SO 3 - + Na + (11) – SO 3 - + H + ⇌ – SO 3 H On the other hand, owing to neutral N atoms in AV6B, AV6B could further be protonated in the acid solution as following: (12) AV 6 B + x H + ⇌ [ AV 6 BH x ] x + Thus, in aqueous acidic solutions, the AV6B exists as neutral form of –SO 3 H and protonated cations of [AV6BH x ] x + . The charge of the metal surface can be determined from the value of E corr − E q=0 (zero charge potential) [47] . The E q=0 of iron is −530 mV vs. SCE in HCl [48] . In the present study, the value of E corr obtained in 1.0 M HCl is −446 mV vs. SCE. The steel surface charges positive in HCl because of E corr − E q=0 (zero charge potential) > 0. Since chloride ions (Cl − ) have a smaller degree of hydration, being specifically adsorbed, they create an excess negative charge towards the solution and favor more adsorption of the cations [49] , [AV6BH x ] x + could adsorb on the negatively charged metal surface. In other words, there may be a synergism between Cl − and protonated AV6B. (ii) Besides the physical adsorption, there should be chemical adsorption. According to some recent quantum chemical calculations of organic inhibitors [23,50–53] , coordination bonds can be formed between the unshared electron pair of N, O atoms and the unoccupied d electronic of Fe. First, coordinate bonds could be formed through sharing the lone electron pairs of N-atom and O-atom in –SO 3 H with the empty orbits of Fe atoms. Second, AV6B contains conjugated double bonds with many π electrons, AV6B can be also adsorbed on the steel surface on the basis of donor–acceptor interactions between π-electrons of the conjugated double bonds and vacant d-orbitals of Fe. Last, AV6B may chemisorb at steel/solution interface via hydrogen bond between –SO 3 H and H 2 O molecules adsorbed on the steel surface. (iii) Due to the chelating action of organic dyes with similar chemical molecular structure of AV6B, some metal complexes of Fe 2+ -organic dyes compounds have been widely prepared [54,55] . Thus, AV6B or [AV6BH x ] x + may combine with freshly generated Fe 2+ ions on steel surface forming metal inhibitor complexes: (13) Fe → Fe 2 + + 2 e (14) AV 6 B + Fe 2 + ↔ [ AV 6 B - Fe ] 2 + (15) [ AV 6 BH x ] x + + Fe 2 + ↔ [ AV 6 BH x - Fe ] ( 2 + x ) + These complexes might adsorb onto steel surface by the van der Waals force to form a blocking barrier to keep CRS from corrosion. (iv) A combination of the above. 4 Conclusions (1) AV6B acts as a very good inhibitor for the corrosion of CRS in 1.0 M HCl. Inhibition efficiency increase with the inhibitor concentration, and the maximum inhibition efficiency is higher than 92% at 20 μM (2.0 × 10 −5 M). The adsorption of AV6B is a spontaneous process and obeys Langmuir adsorption isotherm. (2) The inhibition efficiency increases with immersion time from 2 to 6 h, while remains constant in 6–48 h (93% at 20 μM), then decreases with immersion time within range of 48–144 h. (3) Inhibition efficiency decreases with acid concentration (1.0–5.0 M). The corrosion of CRS in uninhibited and inhibited HCl supports the kinetic equation proposed by Mathur and Vasudevan. The rate constant ( k ) decreases markedly after adding AV6B, while the reaction constant ( B ) increases. (4) AV6B is a mixed-type inhibitor in 1.0 M HCl, and the inhibition action is caused by geometric blocking effect. EIS spectra exhibit one capacitive loop which indicates that the corrosion reaction is controlled by charge transfer process. The addition of AV6B to 1.0 M HCl solutions increases R t while reduces C dl . (5) The adsorption of AV6B involves electrostatic attraction, sharing electrons between the N, O atoms and Fe, donor–acceptor interactions between π-electrons of conjugated double bonds and vacant d-orbitals of Fe, hydrogen bond between –SO 3 H and H 2 O, adsorption of the complexes of [AV6B-Fe] 4+ and [AV6BH x -Fe] (2+ x )+ . Acknowledgement This work was carried out in the frame of research projects funded by Key Construction Course of Chemical Engineering for Forest Products of Southwest Forestry University (XKX200907), Natural Science Foundations of Southwest Forestry University (200715M) and Educational Department of Yunnan Province (09C0181). The electrochemical measurements were carried out using PARSTAT 2273 advanced electrochemical system (Princeton Applied Research) provided by Advanced Science Instrument Sharing Center of Southwest Forestry University. References [1] G. Trabanelli Inhibitors an old remedy for a new challenge Corrosion 47 1991 410 419 [2] L.B. Tang G.N. Mu G.H. Liu The effect of neutral red on the corrosion inhibition of cold rolled steel in 1.0 M hydrochloric acid Corros. Sci. 45 2003 2251 2262 [3] L.B. Tang X.M. Li N. Li Q. Qu G.N. Mu G.H. Liu The effect of 1-(2-pyridylazo)-2-naphthol on the corrosion of cold rolled steel in acid media Part 1: inhibitive action in 1.0 M hydrochloric acid Mater. Chem. Phys. 94 2005 353 359 [4] E.E. Oguzie C. Unaegbu C.N. Ogukwea B.N. Okolue A.I. Onuchuku Inhibition of mild steel corrosion in sulphuric acid using indigo dye and synergistic halide additives Mater. Chem. Phys. 84 2004 363 368 [5] E.E. Ebenso E.E. Oguzie Corrosion inhibition of mild steel in acidic media by some organic dyes Mater. Lett. 59 2005 2163 2165 [6] E.E. Oguzie Influence of halide ions on the inhibitive effect of congo red dye on the corrosion of mild steel in sulphuric acid solution Mater. Chem. Phys. 87 2004 212 217 [7] E.E. Oguzie E.E. Ebenso Studies on the corrosion inhibiting effect of Congo red dye–halide mixtures Pigm. Res. Technol. 35 2006 30 35 [8] E.E. Oguzie G.N. Onuoha A.I. Onuchuku Inhibitory mechanism of mild steel corrosion in 2 M sulphuric acid solution by methylene blue dye Mater. Chem. Phys. 89 2005 305 311 [9] E.E. Oguzie Corrosion inhibition of mild steel in hydrochloric acid solution by methylene blue dye Mater. Lett. 59 2005 1076 1079 [10] E. Oguzie C. Akalezi C. Enenebeaku Inhibitive effect of methyl green dye on the corrosion of low carbon steel in acidic media Pigm. Res. Technol. 38 2009 359 365 [11] E.E. Oguzie V.O. Njoku C.K. Enenebeaku C.O. Akalezi C. Obi Effect of hexamethylpararosaniline chloride (crystal violet) on mild steel corrosion in acidic media Corros. Sci. 50 2008 3480 3486 [12] Y. Abboud A. Abourriche T. Saffaj M. Berrada M. Charrouf A. Bennamara H. Hannache A novel azo dye, 8-quinolinol-5-azoantipyrine as corrosion inhibitor for mild steel in acidic media Desalination 237 2009 175 189 [13] R.Q. Liu L. Xiang X.G. Zhang X. Xia Inhibition effect of methyl red on corrosion of steel in acidic solutions Corros. Prot. 22 2001 98 99 (in Chinese) [14] X.H. Li S.D. Deng H. Fu N. Zhao Y.X. Li G.N. Mu Corrosion inhibition of cresol red for cold rolled steel in phosphoric acid solution Corros. Sci. Prot. Technol. 21 2009 354 357 (in Chinese) [15] J. Sathiyabama S. Rajendran J.A. Solvi A.J. Amalraj Methyl orange as corrosion inhibitor for carbon steel in well water Indian J. Chem. Technol. 15 2008 462 466 [16] E.E. Ebsenso H. Alemu S.A. Umoren I.B. Obot Inhibition of mild steel corrosion in sulphuric acid using alizarin yellow GG dye and synergistic iodide additive Int. J. Electrochem. Sci. 3 2008 1325 1339 [17] R.A. Prabhu T.V. Venkatesha A.V. Shabhag Carmine and fast green as corrosion inhibitors for mild steel in hydrochloric acid J. Iran. Chem. Soc. 6 2009 353 363 [18] H. Ashassi-Sorkhabi D. Seifzadeh M.G. Hosseini EN, EIS and polarization studies to evaluate the inhibition effect of 3H-phenothiazin-3-one, 7-dimethylamin on mild steel corrosion in 1 M HCl solution Corros. Sci. 50 2008 3363 3370 [19] X.H. Li S.D. Deng H. Fu Inhibition effect of methyl violet on the corrosion of cold rolled steel in 1.0 M HCl solution Corros. Sci. 52 2010 3413 3420 [20] X.H. Li S.D. Deng H. Fu T.H. Li Adsorption and inhibition of 6-benzylaminopurine on cold rolled steel in 1.0 M HCl Electrochim. Acta 54 2009 4089 4098 [21] X.H. Li S.D. Deng H. Fu G.N. Mu Inhibition by tween-85 of the corrosion of cold rolled steel in 1.0 M hydrochloric acid solution J. Appl. Electrochem. 39 2009 1125 1135 [22] A. Popova E. Sokolova S. Raicheva M. Christov AC and DC study of the temperature effect on mild steel corrosion in acid media in the presence of benzimidazole derivatives Corros. Sci. 45 2003 33 58 [23] I.B. Obot N.O. Obi-Egbedi Adsorption properties and inhibition of mild steel corrosion in sulphuric acid solution by ketoconazole: experimental and theoretical investigation Corros. Sci. 52 2010 198 204 [24] X.H. Li G.N. Mu Tween-40 as corrosion inhibitor for cold rolled steel in sulphuric acid: weight loss study, electrochemical characterization, and AFM Appl. Surf. Sci. 252 2005 1254 1265 [25] I. Sekine Y. Hirakawa Effect of 1-hydroxyethlidene-1,1-diphosphonic acid on the corrosion of SS41 steel in 0.3% sodium chloride solution Corrosion 42 1986 272 277 [26] E. Cano J.L. Polo A. La Iglesia J.M. Bastidas A study on the adsorption of benzotriazole on copper in hydrochloric acid using the inflection point of the isotherm Adsorption 10 2004 219 225 [27] F. Bentiss M. Lebrini M. Lagrenée Thermodynamic characterization of metal dissolution and inhibitor adsorption processes in mild steel/2,5-bis( n -thienyl)-1,3,4-thiadiazoles/hydrochloric acid system Corros. Sci. 47 2005 2915 2931 [28] W.H. Li Q. He S.T. Zhang C.L. Pei B.R. Hou Some new triazole derivatives as inhibitors for mild steel corrosion in acidic medium J. Appl. Electrochem. 38 2008 289 295 [29] E. Bensajjay S. Alehyen M. El Achouri S. Kertit Corrosion inhibition of steel by 1-phenyl-5-mercapto 1,2,3,4-tetrazole in acidic environments (0.5 M H 2 SO 4 and 1/3 M H 3 PO 4 ) Anti-Corros. Meth. Mater. 50 2003 402 409 [30] F.P. Wang W.L. Kang H.M. Jin Corrosion Electrochemistry Mechanism, Methods and Applications 2008 Chemical Industrial Engineering Press Beijing p. 242 (in Chinese) [31] S.T. Zhang Z.H. Tao S.G. Liao F.J. Wu Substitutional adsorption isotherms and corrosion inhibitive properties of some oxadiazole–triazole derivative in acidic solution Corros. Sci. 52 2010 3126 3132 [32] X.H. Li S.D. Deng G.N. Mu H. Fu F.Z. Yang Inhibition effect of nonionic surfactant on the corrosion of cold rolled steel in hydrochloric acid Corros. Sci. 50 2008 420 430 [33] X.H. Li S.D. Deng H. Fu G.N. Mu Inhibition effect of 6-benzylaminopurine on the corrosion of cold rolled steel in H 2 SO 4 solution Corros. Sci. 51 2009 620 634 [34] I.B. Obot N.O. Obi-Egbedi 2,3-Diphenylbenzoquinoxaline: a new corrosion inhibitor for mild steel in sulphuric acid Corros. Sci. 52 2010 282 285 [35] S.K. Shukla M.A. Quraishi The effects of pharmaceutically active compound doxycycline on the corrosion of mild steel in hydrochloric acid solution Corros. Sci. 52 2010 314 321 [36] P.B. Mathur T. Vasudevan Reaction rate studies for the corrosion of metals in acids-I, iron in mineral acids Corrosion 38 1982 171 178 [37] I. Ahamad M.A. Quraishi Mebendazole: new and efficient corrosion inhibitor for mild steel in acid medium Corros. Sci. 52 2010 651 656 [38] C. Cao On electrochemical techniques for interface inhibitor research Corros. Sci. 38 1996 2073 2082 [39] N. Labjar M. Lebrini F. Bentiss N.E. Chihib S. El Hajjaji C. Jama Corrosion inhibition of carbon steel and antibacterial properties of aminotris-(methylnephosnic) acid Mater. Chem. Phys. 119 2010 330 336 [40] M. Lebrini M. Lagrenée H. Vezin M. Traisnel F. Bentiss Experimental and theoretical study for corrosion inhibition of mild steel in normal hydrochloric acid solution by some new macrocyclic polyether compounds Corros. Sci. 49 2007 2254 2269 [41] A.R.S. Priya V.S. Muralidharam A. Subramania Development of novel acidizing inhibitors for carbon steel corrosion in 15% boiling hydrochloric acid Corrosion 64 2008 541 552 [42] P. Bommersbach C. Alemany-Dumont J.P. Millet B. Normand Hydrodynamic effect on the behaviour of a corrosion inhibitor film: characterization by electrochemical impedance spectroscopy Electrochim. Acta 51 2006 4011 4018 [43] M. Lagrenée B. Mernari M. Bouanis M. Traisnel F. Bentiss Study of the mechanism and inhibiting efficiency of 3,5-bis(4-methylethiophenyl)-4H-1,2,4-triazole on mild steel corrosion in acidic media Corros. Sci. 44 2002 573 588 [44] Q. Qu S.A. Jiang L. Li W. Bai J. Zhou Corrosion behavior of cold rolled steel in peracetic acid solutions Corros. Sci. 50 2008 35 40 [45] M.J. Bahrami S.M.A. Hosseini P. Pilvar Experimental and theoretical investigation of organic compounds as inhibitors for mild steel corrosion in sulfuric acid medium Corros. Sci. 52 2010 2793 2803 [46] X.M. Yang Study on the infrared spectra and Raman spectra of steel rusty layer with atmospheric corrosion Spectrosc. Spectral Anal. 26 2006 2247 2256 [47] D.P. Schweinsberg V. Ashworth The inhibition of the corrosion of pure iron in 0.5 M sulphuric acid by n -alkyl quaternary ammonium iodides Corros. Sci. 28 1988 539 545 [48] G. Banerjee S.N. Malhotra Contribution to adsorption of aromatic amines on mild steel surface from HCl solutions by impedance, UV, and Raman spectroscopy Corrosion 48 1992 10 15 [49] F. Bentiss M. Traisnel M. Lagrenée The substituted 1,3,4-oxadiazoles: a new class of corrosion inhibitors of mild steel in acidic media Corros. Sci. 42 2000 127 146 [50] M.A. Amin K.F. Khaled S.A. Fadl-Allah Testing validity of the Tafel extrapolation method for monitoring corrosion of cold rolled steel in HCl solutions – experimental and theoretical studies Corros. Sci. 52 2010 140 151 [51] A.K. Singh M.A. Quraishi Effect of Cefazolin on the corrosion of mild steel in HCl solution Corros. Sci. 52 2010 152 160 [52] I. Ahamad R. Prasad M.A. Quraishi Adsorption and inhibitive properties of some new Mannich bases of Isatin derivatives on corrosion of mild steel in acidic media Corros. Sci. 52 2010 1472 1481 [53] D.K. Yadav B. Maiti M.A. Quraishi Electrochemical and quantum chemical studies of 3,4-dihydropyrimidin-2(1H)-ones as corrosion inhibitors for mild steel in hydrochloric acid solution Corros. Sci. 52 2010 3586 3598 [54] C. Bouasla M. El-Hadi Samar F. Ismail Degradation of methyl violet 6B dye by the Fenton process Desalination 254 2010 35 41 [55] C. Sarzanini O. Abollino M. Concetta Bruzzoniti E. Mentasti Electrochemical detection of sulphonated azo dyes and their metal complexes in ion interaction chromatography J. Chromatogr. A 804 1998 241 248

Three pyrazine derivatives as corrosion inhibitors for steel in 1.0M H2SO4 solution

Two pyrazine derivatives as inhibitors of the cold rolled steel corrosion in hydrochloric acid solution

Triazolyl blue tetrazolium bromide as a novel corrosion inhibitor for steel in HCl and H2SO4 solutions

Inhibition Effect of Pyrimidine Derivatives on the Corrosion of Steel in Hydrochloric Acid Solution

Experimental and Computational Anticorrosion Behaviors of Pyrazole s-Triazine/anilino-morpholino Derivatives for Steel in Acidic Solutions

Electrochemical, Morphological and Anti-corrosive Characteristics of Pyrazine Derivatives for Mild Steel Corrosion in Aggressive Medium: A Comparative Study

Detailed experimental performance of two new pyrimidine-pyrazole derivatives as corrosion inhibitors for mild steel in HCl media combined with DFT/MDs simulations of bond breaking upon adsorption

Synthesis of new binary trimethoxyphenylfuran pyrimidinones as proficient and sustainable corrosion inhibitors for carbon steel in acidic medium: experimental, surface morphology analysis, and theoretical studies

Acid violet 6B as a novel corrosion inhibitor for cold rolled steel in hydrochloric acid solution

Highly effective inhibition of mild steel corrosion in HCl solution by using pyrido[1,2-a]benzimidazoles

Anticorrosion Effect of Ethoxylate Sulfanilamide Compounds on Carbon Steel in 1 M Hydrochloric Acid: Electrochemical and Theoretical Studies

Corrosion Inhibition and Adsorption Properties of Some Heterocyclic Derivatives on C-Steel Surface in HCl

Corrosion inhibition performance of synergistic inhibitors on Q235 steel in methanol/formic acid medium

Experimental and Theoretical Study on the Synergistic Inhibition Effect of Pyridine Derivatives and Sulfur-Containing Compounds on the Corrosion of Carbon Steel in CO2-Saturated 3.5 wt.% NaCl Solution

N-substituted Methyl Ethylenediamine Derivatives As Corrosion Inhibitors for Carbon Steel in 1 M Hydrochloride Acid

Two Phenylpyrimidine Derivatives As New Corrosion Inhibitors for Cold Rolled Steel in Hydrochloric Acid Solution

Adsorption and corrosion inhibition performance of two planar rigid pyridinecarboxaldehyde-based double Schiff bases for mild steel in HCl solution: Experimental and computational investigations

Investigation on corrosion protection behavior and adsorption of carbohydrazide-pyrazole compounds on mild steel in 15% HCl solution: Electrochemical and computational approach

Experimental and Theoretical Study on the Synergistic Inhibition Effect of Pyridine Derivatives and Sulfur-Containing Compounds on the Corrosion of Carbon Steel in CO₂-Saturated 3.5 wt.% NaCl Solution

Multifunctional Aspects of the Synthesized Pyrazoline Derivatives for AP1 5L X60 Steel Protection Against MIC and Acidization: Electrochemical, In Silico, and SRB Insights

Enhanced corrosion resistance of carbon steel in an aggressive environment by a recently developed pyrazole derivative: Electrochemical, SEM/XPS/AFM, and theoretical investigation