Abstract:A novel glucose biosensor based on the electrochemical detection of enzymatically generated H2O2 was constructed by the effective immobilization of glucose oxidase (GOD) via glutaraldehyde cross-linking with a poly(thionine) (PTH)-modified Au electrode, followed by coating with a Nafion outer layer to obtain high selectivity. An electrochemical quartz crystal microbalance (EQCM) was used to track various modification procedures. The mass of the deposited PTH via cyclic voltammetric electropolymerization of thionine in aqueous H2SO4 was estimated from the “dry” frequency shift after fully removing the PTH layer via its acidic degradation, allowing us to evaluate the electroactivity per unit mass of PTH. A Nafion/glucose oxidase-glutaraldehyde/poly(thionine)/Au electrode was thus constructed for glucose sensing. We found that the PTH film is a good matrix to immobilize more GOD, and the performance of the constructed sensor is significantly improved compared with its absence, though its mediator effect on the enzyme electrode is negligible. Influence of various experimental parameters on glucose sensing, including the applied potential, solution pH and electroactive interferents, was investigated. At an optimal potential of 0.7V versus the KCl-saturated calomel electrode (SCE), the glucose biosensors were linear with glucose concentration from 0.005 to ∼5mmolL−1, with high sensitivity (13.5Amol−1cm−1), short response time (within ca. 10s) and good anti-interferent ability. The Michaelis constant (Kmapp) of the immobilized GOD was estimated to be 5.47mmolL−1. The biosensor exhibited good storage stability, i.e., 83% of its initial response was retained after 1-month storage in a pH 7.0 phosphate buffer at 4°C. The effective enzymatic specific activity (ESA, defined as enzymatic activity per gram of enzyme) of immobilized GOD was estimated to be 6.85kUg−1 on the basis of the mass of immobilized GOD (from EQCM) and the quantity of hydrogen peroxide as the product of the enzymatic reaction (from amperometric detection), and the leakage of H2O2 from the Nafion/GOD-GA/PTH/Au enzyme electrode at the detection potential, as characterized by a scanning electrochemical microscope (SECM), was found to be an important factor influencing the ESA estimation.

Glucose sensor for flow injection analysis of serum glucose based on immobilization of glucose oxidase in titania sol-gel membrane.

A glucose oxidase sensor based on screen-printed carbon electrodes modified by polypyrrole.

An Amperometric Glucose Biosensor Based on Titania Sol-gel/Prussian Blue Composite Film

Immobilization of glucose oxidase in sol–gel matrix and its application to fabricate chemiluminescent glucose sensor

A Glucose Electrochemical Sensor Based on Glucose Oxidase Immobilized in Aminopropyl-Magnesium Phyllosilicate Nanosheets Matrix

Co-immobilization of glucose oxidase and hexokinase on silicate hybrid sol-gel membrane for glucose and ATP detections.

Preparation of Immobilized Glucose Oxidase Column by Sol-gel Technique and Its Application to the Chemiluminescent Glucose Sensor

Preparation of GOD/Sol-Gel Silica Film on Prussian Blue Modified Electrode for Glucose Biosensor Application

Preparation of the Glucose Sensor Based on Three-Dimensional Ordered Macroporous Gold Film and Room Temperature Ionic Liquid

A glucose biosensor with enzyme-entrapped sol–gel and an oxygen-sensitive optode membrane

Amperometric Detection of Glucose with Glucose Oxidase Absorbed on Porous Nanocrystalline TiO2 Film

Amperometric Glucose Biosensor Based on Sol-Gel Organic-Inorganic Hybrid Material.

Improved biosensor for glucose based on glucose oxidase-immobilized silk fibroin membrane

Flow Injection Analytical System for Glucose with Screen-Printed Enzyme Biosensor Incorporating Os-complex Mediator

Immobilization of Glucose Oxidase into a Nanoporous TiO2 Film Layered on Metallophthalocyanine Modified Vertically-Aligned Carbon Nanotubes for Efficient Direct Electron Transfer

Al2O3 Sol–gel Derived Amperometric Biosensor for Glucose

An Amperometric Glucose Biosensor Constructed by Immobilizing Glucose Oxidase on Titanium-Containing Mesoporous Composite Material of No. 41 Modified Screen-Printed Electrodes.

One-Step Immobilization Of Glucose Oxidase In A Silica Matrix On A Pt Electrode By An Electrochemically Induced Sol-Gel Process

Construction As Well As Eqcm and Secm Characterizations of A Novel Nafion/Glucose Oxidase-Glutaraldehyde/Poly(Thionine)/Au Enzyme Electrode for Glucose Sensing

Glucose Biosensor Based on Immobilization of Glucose Oxidase in Electrochemically Polymerized Polytyramine Film and Overoxidised Polypyrrole Film on Platinized Carbon Paste Electrode

Glucose Biosensor Based on Immobilization of Glucose Oxidase on Porous Screen Printed Electrodes