Abstract:Functional gradient materials (FGM), with their composition gradually varied in different positions, have attracted much attention for research and development during the years. Normally there are two types of functional gradient materials: one without the formation of intermetallics which is easier for fabrication due to less scientific and technological challenge; the other one with the formation of intermetallics in some part of the gradient changed composition range such as Ti-Al, Ti-Fe, Ni-Al gradient materials, which still exists big challenge on intermetallic, resulting in high brittleness and unavailability.Laser deposition is a competitive candidate for FGM due to its capability on accurate composition and precise dimension control. According to an aeronautical application requirement to gradually change the composition from Ti6Al4V to 316L, this paper reports on laser deposition of Ti6Al4V to 316L gradient composition structure. A big challenge is the formation of the TiFe intermetallic especially near the composition of Ti50Fe50, which results in very high cracking tendency. Many efforts have been made to optimize the Ti-Fe composition ratio, the deposition process and the deposition parameters, not a single Ti6Al4V-316L composition gradient structure was successful due to the formation of the very brittle TiFe and TiFe2 intermetallics. This indicates that it is almost impossible to direct deposit Ti6Al4V to 316L without cracking and separation. We used Inconel 625 powder as an interlayer between the Ti6Al4V and the 316L, thus a sound Ti6Al4V-316L composition gradient structure was successfully achieved by laser deposition. The brittle TiFe and TiFe2 intermetallics were replaced by a series of phase evolutions: α+β → β+Ti2Ni→Ti2Ni+TiNi→TiNi→TiNi+TiNi3→Ni3Fe→ Ni2Fe3→γFe. The brittleness was dramatically decreased or diluted and crack-free composition gradient structure was available. The gradient structure was further analyzed on hardness, microstructural evolution, the Young's modulus and Poisson's ratio.

Rapid Prototyping and Combustion Synthesis of TiC/Ni Functionally Gradient Materials

Microstructure and mechanical properties of TiC-Ni functionally graded materials by simultaneous combustion synthesis and compaction

Combustion Synthesis and Thermal Stress Analysis of TiC–Ni Functionally Graded Materials

COMBUSTION SYNTHESIS AND THERMAL STRESS ANALYSIS OF TIC-NI FGM

Rapid Fabrication of Functionally Gradient Material Parts by Laser Beam

Fabrication of Al2O3/TiC/Ni Functionally Graded Materials by Pulsed-Electric Current Sintering and Their Mechanical Properties.

Fabrication and Microstructure of Zro2-Ni Functional Gradient Material by Powder Metallurgy

Synthesis of Functionally Graded AA7075-B4C Composite with Multi-Level Gradient Structure

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Laser Deposition of Ti6Al4V-316L Composition Gradient Structure: Challenge on Intermetallics

Fabrication of multi-functional Ni–Ti alloys by laser powder bed fusion

Mechanical Properties and Formation Mechanism of Ti/SiC System Gradient Materials Fabricated by In-Situ Reaction Laser Cladding

Spark Plasma Sintering of Functionally Graded Material in the Ti–TiB2–B System

Optimum Design of TiC-Ni Functionally Graded Materials

FABRICATION AND CHARACTERIZATION OF FUNCTIONALLY GRADED Ni–Ti MULTILAYER THIN FILMS

ELASTOPLASTIC OPTIMUM DESIGN OF Ni/TiC FUNCTIONAL GRADIENT MATERIAL

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

TiC-Ni functionally gradient material produced by SHS

Fabrication of functionally graded materials from a single material by selective evaporation in electron beam powder bed fusion

Combustion synthesis TiC-Al2O3/Fe FGM and its resisting thermal shock behaviors

Research on the microstructure and mechanical properties of functional gradient materials of TC4/TC11 titanium alloys for wire arc additive manufacturing with different transitional forms