Abstract:Since 2002, ultra wideband (UWB) technology has ignited the interests of academia and industry for its potential of achieving high-speed wireless communication in short distance with low power. It is actively investigated today due to the wide available bandwidth for very high data rate up to 480Mb/s and low power service over short distances in 10m range. According to FCC (Federal Communications Commission), the frequency spectrum allocated for UWB is 3.1-10.6 GHz, and the spectrum shape of modulated output power and maximum power level are limited to -41.3dBm/MHz, which ensures that UWB can coexist with existing spectrum users like GSM(Global System of Mobile communication), WLAN(Wireless Local Area Network) and Bluetooth. Based on MB-OFDM(Multi-Band Orthogonal Frequency Division Multiplexing), WiMedia released the initial version of Physical Layer (PHY) Specification in September 2005. In this proposal, the UWB frequency spectrum from 3.1 GHz to 10.6 GHz is divided into 14 channels with 528MHz for each channel. These sub-bands are grouped into five band groups. It is seen that by increasing the signal bandwidth significantly, ultra-wideband achieves a high channel capacity and becomes an attractive solution to the ever-increasing data rate demands in wireless personal area networks (WPAN). In December 2005, European Computer Manufacturer's Association (ECMA) proposed the standard ECMA 368/369 on high-speed UWB physics layer and media access control layer based on MBOFDM scheme. This has pushed the industrialization of UWB technology to a new stage again. In China, UWB technology has also become a hot topic according to the issue of the UWB standard by Chinese Government in 2008. A new UWB scheme named dual carrierorthogonal frequency division multiplexing (DC-OFDM ) has been proposed and applied in China. In China standard, only the band from 6.2GHz to 9.4GHz and the band from 4.2GHz to 4.8GHz are available for UWB applications. These bands are partitioned into 14 subbands of 264MHz bandwidth which means the bandwidth is halved in China’s DC-OFDM standard compared with the ECMA 368/369 standard. Thus the sampling frequency of the DACs(Digital-to-Analog Converter) and ADCs(Analog-to-Digital Converter) are halved too. The power consumption of the system can be reduced greatly. Moreover, in DC-OFDM

A 6.2–9.5 GHz Receiver for Wimedia MB-OFDM and China UWB Standard

A 6.2–9.5 GHz UWB receiver for WiMedia MB-OFDM

Flexible analog baseband for WiMedia MB-OFDM and China UWB standard

A Dual-Mode 6-9 GHz Transmitter for OFDM-UWB

A 3.1–4.8 GHz CMOS receiver for MB-OFDM UWB

A group-selected and gain controllable CMOS active mixer for UWB applications

A 100mhz-2ghz Wireless Receiver In 40-Nm Cmos For Software-Defined Radio

A Monolithic 3.1-4.8 GHz MB-OFDM UWB Transceiver in 0.18-Μm CMOS

Design of a Low Power 60ghz OOK Receiver in 65nm CMOS Technology

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

Design of 6.2—9.4 GHz DC-OFDM UWB Receiver RF Front-End

3 A 0 . 13 Um CMOS 6-9 GHz 9-Bands Double-Carrier OFDM Transceiver for Ultra Wideband Applications

A Current-Mode RF Transmitter for 6–9 GHz MB-OFDM UWB Application

An Rf Transmitter Front-End Implementation In 0.18 Mu M Cmos For Ofdm-Uwb

A 3.1–4.8 GHz Transmitter with a High Frequency Divider in 0.18 Μm CMOS for OFDM-UWB

An RF Transmitter Front-End Implementation in 0.18&#x03bc;m CMOS for OFDM-UWB

A Robust Cmos Rf Front-End Design for 3.1-4.8Ghz Mb-Ofdm Uwb System

A 6-7 GHz, 40 Db Receiver RF Front-End with 4.5 Db Minimum Noise Figure in 0.13μm CMOS for IR-UWB Applications

A 3.8-mW 3.5-4-GHz regenerative FM-UWB receiver with enhanced linearity by utilizing a wideband LNA and dual bandpass filters