Abstract:The most common manufacturing process for wrought magnesium alloy sheet is warm-rolling and the microstructure and properties of the product are strongly related with the rolling temperature. In particular; {10 (1) over bar1}-{10 (1) over bar2} double twinning is an important supplemental mechanism for the deformation of magnesium alloys during rolling at low or moderate temperatures. Therefore, the present work studies the microstructural variation of magnesium alloy sheets AZ31 rolled to 9% at different temperatures in the range of 150-350 degrees C, and discusses the influence of rolling temperature on the quantity and variety of {10 (1) over bar1}-{10 (1) over bar2} double twins, as well as recrystallization related to the double twins. The mechanical properties of the rolled sheets and the influences of twins on the mechanical properties have also been discussed. The results show that {10 (1) over bar1}-{10 (1) over bar2} double twins are observed in the sheets rolled at temperature ranging from 150 to 300 degrees C. The fraction of double twin per unit area, and the number of variant types within each primary twin, decreases with the increasing rolling temperature. At the temperature above 250 degrees C; only co-planar double twins are observed in each primary twin. Recrystallized grains are observed to nucleate at the twin boundaries in the sheets rolled above 250 degrees C, these can consume the twin boundaries and resulting in merging of the twin grains. No {10 (1) over bar1}-{10 (1) over bar2} twins are found in the AZ31 magnesium alloy sheet rolled at 350 degrees C. With the increase of rolling temperature, the yield strength decreases and the ductile elongation increase for the rolled magnesium alloy sheet.

Hot Deep Drawing Property of Electromagnetic Field and Ultrasonic Field Cast-Rolling AZ31B Mg Alloy Sheets

Study on the hot deep drawing performance and microstructural evolution of AZ91D magnesium alloy sheets

Drawing Process and Properties of Roll-casting AZ31 Magnesium Alloy Sheet

Experimental Study of Hot Deep Drawing for Twin-Roll-cast AZ31 Alloy

Microstructure, Texture Evolution, and Mechanical Properties of Thin AZ31B Mg Alloy Sheets Prepared by Two-Stage Rolling

Evolution of the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets during Multi-Pass Lowered-Temperature Rolling

Deformation Microstructure and Characteristics of Cast-Rolling and Normal Rolling AZ31 Magnesium Alloy Sheets

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Grain refining and improving mechanical properties of AZ31 Mg alloy sheets by multi-pass warm rolling with falling temperature

Effect of Final Rolling Temperature on Microstructures and Mechanical Properties of AZ31 Alloy Sheets Prepared by Equal Channel Angular Rolling and Continuous Bending

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Strength-ductility balance of Mg-1.03Ca-0.47Mn Mg alloy sheet produced by rolling and annealing

Influence of Microstructure and Mechanical Properties on Formability in High Strain Rate Rolled AZ31 Magnesium Alloy Sheets

Microstructure and Hot Deformation Behaviour of Twin-Roll Cast AZ31 Magnesium Wire

Study of Effects of Initial Texture on the Microstructure and Texture for Hot Rolled AZ31 Mg Alloy Sheet Using EBSD

Effect of pack-rolling temperature on microstructure and mechanical properties of Mg-6Sn-3Al-1Zn Alloy

Effects of Compound Energy Field on Microstructure and Mechanical Properties of Roll-Casted AZ61 Magnesium Alloy Strip

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Microstructure Evolution and Mechanical Properties of AZ31 Magnesium Alloy Sheets Prepared by Low-Speed Extrusion with Different Temperature

Significantly improvement in formability and ductility of AZ31 Mg alloy by differential temperature rolling

INFLUENCE OF ROLLING TEMPERATURE ON THE {1011}-{1012} TWINNING IN ROLLED AZ31 MAGNESIUM ALLOY SHEETS