Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Experiments on the Transient Heat Transfer of Minichannel Heat Sink under High Heat Flux Density in an Enclosed Loop

Theoretical and Experimental Research on Flow Boiling Heat Transfer in Microchannels for IGBT Modules

Experimental Investigation of Heat Transfer Performance for a Novel Microchannel Heat Sink

Experimental Study on an Thermosyphon Loop with Bubble Pump Effect

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Numerical Study of Laminar Heat Transfer and Pressure Drop Characteristics in A Water-Cooled Minichannel Heat Sink

Experimental and Numerical Study of Transient Electronic Chip Cooling by Liquid Flow in Microchannel Heat Sinks

High heat flux dissipation of membrane-venting heat sink with thin film boiling

Experimental study of flow boiling in microchannel heat sink enhanced with partially in-line pin fins fence arrangement

Experimental Study on Cooling Performance of a Hybrid Microchannel and Jet Impingement Heat Sink

Experimental and numerical study of structural parameters on the heat transfer performance of submerged cooling system

A Microchannel Heat Sink with Unitary Circular Flow and Short Distance Heat Transfer Mode: Design and Analysis

Experimental study on flow boiling characteristics of R134a inside high-heat-flux microchannels

STUDY ON TWO-PHASE FLOW AND TEMPERATURE UNIFORMITY CHARACTERISTICS OF MICROCHANNEL HEAT PIPE

Transient Heat Transfer Characteristics in a Flat Plate Heat Sink with Mini-Channels for Cooling High Heat Flux IGBT

Effects of wave number and average radius on flow and heat transfer in a curve-wave channel

Experimental Study on Flow Boiling Characteristics of R-1233zd(E) of Counter-Flow Interconnected Minichannel Heat Sink

Experimental Study on the Flat Loop Heat Pipe with Minichannel Wick under Low Heat Flux

EXPERIMENTAL RESEARCH ON COUPLED HEAT TRANSFER OF A HEAT SOURCE ENCAPSULATED INTO A SUBATMOSPHERIC HYPOBARIC CHAMBER

Flow and Heat Transfer Performances of Liquid Metal Based Microchannel Heat Sinks under High Temperature Conditions

On the assessment of the thermal performance of microchannel heat sink with nanofluid