Abstract:A new cascade impactor has been developed with the arrangement of the classifying nozzles optimized for analysis of the collected particles by total reflection X-ray fluorescence (TXRF). TXRF offers detection limits in the range of a few picograms of absolute mass and therefore poses great potential for the elemental analysis of heavy metals in aerosol particles. To fully exploit this high sensitivity, particles have to be collected in the effective analysis area of the TXRF instrument, which is often smaller than typical deposition patterns of commercial impactors or filter samplers. This is achieved by a novel compact arrangement of the classifying nozzles within a circular area of a diameter of less than 5 mm . A decreasing density of the nozzle spacing from the inside to the outside of the nozzle cluster allows for constant cross-flow conditions, minimizing the mutual influence of the individual nozzles. The design of a multistage cascade impactor is presented to individually sample PM 10 , PM 2.5 and PM 1 size fractions. Considering the high sensitivity of TXRF analysis, constructive measures have been taken to prevent attrition of impactor material which might lead to methodical blank values. Experimental validation confirms that neither attrition nor cross-contamination can be observed. Furthermore, a new spin-coating method has been developed which makes it possible to apply a thin and defined adhesive layer of grease to the sample carrier with good repeatability. Application of the impactor in a case study at an urban site at Potsdamer Platz, Berlin, Germany, shows that sampling at a moderate volume flow rate of 5 L min −1 , the particle mass collected in 30 min or less is sufficient for reliable TXRF analysis of heavy metal concentrations ( Fe , Zn , Cu , Mn , Pb and Ni ) in ambient aerosol. This high time resolution enables snapshot sampling, e.g. to quantify variations in particle source strengths. Overall, the new impactor optimized for TXRF analysis bears great potential to improve the quantification of particulate trace metals and other elements in PM 10 , PM 2.5 and PM 1 with high time resolution.

Design of multi-nozzle PM10 -PM2. 5 cascade impactor and its application

System Integration of an Optimally Designed Virtual Impactor with a QCM Sensor As a One-Stop PM2.5 Classification and Detection Platform

Development and Application of Multi-channel PM2.5 Species Sampler

[Development of a Two Stage Virtual Impactor for Stationary Source PM10 and PM2.5 Sampling].

Development of a cascade impactor optimized for size-fractionated analysis of aerosol metal content by total reflection X-ray fluorescence spectroscopy (TXRF)

Standard particle experimental validation of cutpoint diameters on novel cascade impactor

[Application of a Two-stage Virtual Impactor in Measuring of PM10 and PM2.5 Emissions from Stationary Sources].

Computational Fluid Dynamics (CFD) Investigation of the Gas–solid Flow and Performance of Andersen Cascade Impactor

Design and Application of a Novel Atmospheric Particle Sampler

Design and Analysis of Particulate Matter Air-Microfluidic Grading Chip Based on MEMS

Sampling Efficiency of Low-Volume PM10 Inlets with Different Impaction Substrates

Experimental Study on Droplet Diameter for PM10 of Mine Dust

Analysis of Portable Impactor Performance for Enumeration of Viable Bioaerosols

Numerical Simulation of Aerosol Dynamics in an Impinging Jet with Microdroplet Coalescence

Numerical study on the effect of nozzle-converging length on the aerosols collection efficiency and deposition on the impaction plate of a multi-nozzle inertial impactor

A Real-Time Approach to Detect PM2.5 in a Seriously Polluted Environment Based on Pressure Drop

The effect of sampling inlets on the PM-10 and PM-15 to TSP concentration ratios

Investigation on Optimal Selection of Multi-Nozzle Spray Dust Suppression Parameters for Air-Operated Spraying System

Optimal Design of Nozzle for Supersonic Atmosphere Plasma Spraying

PARTICLE SIZE DETERMINATION OF LIQUID DROPLETS IN GAS FLOW BY USING IMPACT DIAPHRAGM METHOD

Application of a Resuspension Test Chamber in PM_（2.5） Source Profile Analysis