Abstract:Magnesium is receiving great attention for transport applications, particularly its cast alloys. This investigation focuses on the as-cast microstructure and mechanical properties of permanent-mould cast Mg–Zn–Al alloys with typical compositions within the high zinc castable domain. Three types of alloys were identified and characterized by Mg32(Al, Zn)49, also known as the τ phase; MgZn phase, also known as the ɛ phase; and a ternary icosahedral quasi-crystalline phase, denoted as the Q phase, respectively. A schematic phase diagram is proposed to show the change of microstructral constituents with element content and the Zn/Al ratio. The diagram reveals that the microstructral constituent is dominated by both the content of Zn or Al and the Zn/Al mass ratio; alloys with a high Zn/Al ratio and a low Al content fall into the ɛ-type; alloys with an intermediate Zn/Al ratio and an intermediate Al content favour the τ-type; and those with a low Zn/Al ratio and a high Al are dominated by the icosahedral quasi-crystalline phase. No Mg17Al12 (γ) phase was found in those ZA series alloys. The solidification process and its effects on the phase constituents were discussed. Preliminary mechanical property testing showed that all the experimental alloys possess comparable ultimate strength and yield strength with the AZ91 alloy at ambient temperature, but show far superior creep resistance at elevated temperatures. Moreover, while ambient-temperature properties solely depend on the total element contents, the τ- and the Q-type alloys show greater potential than the ɛ-type alloys on the improvement of elevated temperature properties.

Effect of Cooling Rate and Composition on Microstructures and Properties of Zn-Mg Alloys

Effect of cooling rate and composition on microstructures and properties of Zn-Mg alloys

Effects of Cooling Rate on Microstructure, Mechanical and Corrosion Properties of Mg–Zn–Ca Alloy

Effect of Cooling Rates and Zr Addition on the Microstructure and Corrosion Behaviors of the Mg–Zn–Gd Alloys

Effect of Zn Concentration on the Microstructure and Mechanical Properties of Al-Mg-Si-Zn Alloys Processed by Gravity Die Casting

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Effect of Cooling Rate on Solidification Structure of Zinc-Aluminum-Magnesium Alloy

Effects of Zn Concentration and Heat Treatment on the Microstructure, Mechanical Properties and Corrosion Behavior of As-Extruded Mg-Zn Alloys Produced by Powder Metallurgy

Effects of Zn on Microstructure, Mechanical Properties and Corrosion Behavior of Mg–Zn Alloys

Effects of Mg Content and Cooling Rate on Microstructure and Corrosion Behavior of Mg-Cu-Zn-Y Bulk Metallic Glass Composites

Microstructure, Mechanical Properties and Corrosion Behavior of Mg-Zn-Zr Alloys with Different Compositions

Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

Effect of Composition on the Microstructure and Mechanical Properties of Mg–Zn–Al Alloys

Microstructure and properties of biodegradable Zn-1.5Mg alloy

Effects of Zn on Microstructure, Mechanical Properties and Corrosion Behavior of Mg-Sr Alloy

Effect of the Zn/Mg Ratio on Microstructures, Mechanical Properties and Corrosion Performances of Al-Zn-Mg Alloys

Effect of composition on the microstructure and mechanical properties of Mg-Al-Zn alloys

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Effect of Extrusion Temperature on the Microstructure, Mechanical Properties, and in Vitro Corrosion Behavior of a Biodegradable Mg-Zn-Ca-Mn-Sn Alloy

Microstructures and Biocorrosion Properties of Biodegradable Mg–Zn–Y–Ca–xZr Alloys

Effects of Zn Content on Microstructure, Mechanical and Degradation Behaviors of Mg-xZn-0.2Ca-0.1Mn Alloys