Abstract:The preparation process-dependent phase morphology of blends composed of nylon 6 and acrylonitrile-butadiene-styrene (ABS) over a composition range of 30-70 wt% using a styrene-maleic anhydride (SMA) copolymer as the compatibilizing agent with a constant content (5phr) was investigated. The results of the scanning electron microscope (SEM) observation revealed that compared with the binary blends of nylon 6 and ABS, the existence of SMA caused a composition shift of phase inversion to a higher weight fraction of nylon 6 when ABS was blended with the preblended nylon 6/SMA blend, while the co-continuous structures could be observed over a considerably narrower composition range when nylon 6 was blended with the pre-blended ABS/SMA blend. An examination through dynamic mechanical analysis (DMA) tests confirmed the results obtained with SEM. It is found that near the phase inversion region a remarkable change in the dynamic storage modulus (G') and the loss tangent (tan delta) appears. Moreover, the influence of blending sequence on the size of dispersed particles has been probed for uncompatibilized and compatibilized blends of nylon 6 and ABS over a wide range of compositions below or beyond the phase inversion points. For the blends of ABS dispersed in a nylon 6 matrix, little discernible effects of blending sequence on particle size could be observed. Furthermore, there exists a significant difference in morphologies of the blends prepared by nylon 6 particles dispersing in a ABS matrix in cases of different blending sequences used. Some possible factors responsible for the above asymmetric behaviors have been proposed.

Studies on Polymer Blends with Moderate Specific Interactions. 2. Phase Structure of Blends SAN/TPU and SAN/TPU/EVA

Phase Behavior of Ternary Homopolymer/Gradient Copolymer Blends

Structure-property Relationships of Reactively Compatibilized PHB/EVA/starch Blends.

Morphology and Mechanical Properties of Blends of Thermoplastic Polyurethane and Polyolefins

Miscibility and Morphology of AB/C‐type Blends Composed of Block Copolymer and Homopolymer or Random Coploymer, 2. Blends with Random Copolymer Effect

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Miscibility, morphology and fracture toughness of tetrafunctional epoxy resin/poly (styrene-co-acrylonitrile) blends

Properties And Crystallization Behavior Of Poly (Vinylidene Fluoride) (Pvdf)/Thermoplastic Polyurethane Elastomer (Tpu) Blends

Phase behavior of blends of poly (vinyl methyl ether) with styrene-acrylonitrile in film

A polymer of bisphenol A and bisphenol A diglycidyl ether and its blends with poly(styrene-co-acrylonitrile):In situ polymerization preparation, morphology, and mechanical properties

Interaction of Microstructure and Interfacial Adhesion on Impact Performance of Polylactide (PLA) Ternary Blends

Miscibility, Morphology and Fracture Toughness of Epoxy Resin/poly(styrene-Co-acrylonitrile) Blends

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

STUDY ON PHASE STRUCTURE AND MECHANICAL PROPERTIES OF PBT AND PA6 BLENDS

Studies of Latex Blends of Natural Rubber/poly(methyl Methacrylate-Co-2-ethylhexyl Methacrylate) and Their Comparison with Incompatible Natural Rubber/poly(methyl Methacrylate)

Effect of Phase Morphology on the Reactive Blending

Ternary Thermosetting Blends of Epoxy Resin, Poly(ethylene Oxide) and Poly(ε‐caprolactone)

The Effect of Blending Sequence on Phase Morphology of Nylon 6/abs/sma Blends

Controls of Gradient Morphology and Surface Properties of Polymer Blends

EFFECT OF PHASE SEPARATION ON DYNAMIC VISCOELASTICITY OF POLY (METHYL METHACRYLATE)/POLY (Α-Methylstyrene-co-acrylonitrile) BLENDS

Effects of Compatibilizing Agent and in Situ Fibril on the Morphology, Interface and Mechanical Properties of EPDM/nylon Copolymer Blends