Abstract:Laser ultrasound (LU) is a contactless and couplant-free remote non-destructive (NDE) technique, which uses lasers for ultrasonic generation and detection rather than conventional piezoelectric transducers. For a transducer, an important characteristic is the directivity , the angle-dependent amplitude of the ultrasonic waves generated in the material. In the non-destructive thermoelastic regime, LU source has been widely modelled as a surface force dipole. However, the directivity of LU in more complex material, where there is an increasing demand for NDE, such as carbon fibre reinforced plastic (CFRP), is yet to be understood. In the current paper, a finite element (FE) modelling methodology to obtain the directivity of LU in complex material is presented. The method is applied to a conductive isotropic material (aluminium, Al) for validation against an existing analytical solution and then applied to a heterogeneous anisotropic material (carbon-fibre reinforced plastic, CFRP). To get the directivity of a specific wave mode, the signal for that mode needs to be resolved in time from other modes at all angles. This is challenging for shear (S) waves in a small model domain due to the head wave, so a technique for suppressing the head wave is shown. The multi-physics model solves for thermal expansion, which models the laser source as a surface heat flux for the Al case, and a buried heat source for the CFRP case, according to where the energy is deposited in the material. The same ultrasound generation pattern can be obtained by using a suitable pure elastodynamic loading, which is shown to be a surface force dipole as per the validation case for Al, and a buried quadrupole for the CFRP case. The modelled directivities are scaled and fitted to experimental measurements using maximum likelihood , and the goodness of fit is discussed. For the Al case, the S wave is preferred over the longitudinal (L) wave for inspection due to greater signal amplitude. For the CFRP case, the quasi-longitudinal (qL) wave in CFRP shows a maximum amplitude directly below the source, and has a greater amplitude than the quasi-shear (qS) wave, suggesting a better choice for inspection.

Simulation on thermoelastic stress field and laser ultrasound waveform in non-metallic materials by using FEM

A Study of Inner Crack Testing with the Laser Phased Array Method.

Modification of the phonon thermal conductivity in spatially confined semiconductor nanofilms under stress fields

Detecting features of defect metal based on laser ultrasonic technique

INTEGRATED TECHNOLOGY FOR DETECTION AND REPAIR OF MECHANICAL COMPONENT SURFACE FATIGUE MICROCRACKS USING PULSED LASER

Simulations Of Ultrasonic Waveform Excited By Pulsed Laser By Using Finite Element Method

Numerical Simulation of the Ultrasonic Pulse Wave Propagation at Solid-Solid Interface

Non-destructive evaluation of non-uniform stress fields and subsurface stress gradients using ultrasonic waves

Finite Element Simulation of the Frictional Heating of Cracks under Excitation of Intensive Ultrasonic Waves

Electromagnetic Ultrasonic Measurement for Welding Residual Stress Detection - Comparison Between Experiment with Numerical Simulation

Simulations Of Bulk Ultrasonic Waveform Excited By Pulsed Laser For Two-Layer Medium Using Finite Element Method

Finite element modeling of heating phenomena of cracks excited by high-intensity ultrasonic pulses

Stress waves in laser-material interaction: From atomistic understanding to nanoscale characterization

Simulation Of Elastic Waves In Viscoelastic Solids Using Finite Elements Method

Finite element modelling strategy for determining directivity of thermoelastically generated laser ultrasound

Numerical simulation of laser-generated Rayleigh wave pulses propagation in the machined surface with residual stress using finite-difference method

Finite element model for femtosecond laser pulse heating using dual phase lag effect

Thermoelastic Wave in Metal Induced by Ultrafast Laser Pulses

Thermoviscoelastic Finite Element Modeling of Laser-Generated Ultrasound in Viscoelastic Plates

A novel model of nonlocal photoacoustic and plasmaelastic heated by laser pulsed excitation of nanoscale semiconductor medium

Simulation of temperature field and stress field of selective laser melting of multi-layer metal powder