Abstract:Crescent‐shaped hydrogel microparticles have been shown to template uniform volume aqueous droplets upon simple mixing with aqueous and oil media for various bioassays. This emerging "lab on a particle" technique requires hydrogel particles with tunable material properties and dimensions. The crescent shape of the particles is attained by aqueous two‐phase separation of polymers inside a spherical droplet followed by photopolymerization of the curable precursor. In this work, we have investigated the phase separation of photo‐curable poly(ethylene glycol) diacrylate (PEGDA, Mw 700) and dextran (Mw 40,000) for tunable manufacturing of crescent‐shaped particles. The particles' morphology was precisely tuned by following a phase diagram, varying the UV intensity, and adjusting the flow rate ratio between the three streams, containing PEGDA, dextran, and oil, within a microfluidic droplet generation device. The fabricated particles with variable cavity sizes and outer diameters encapsulated uniform aqueous droplets upon mixing with a continuous oil phase. The particles were fluorescently labeled with red and blue emitting dyes at variable concentrations to produce six color‐coded particles. The blue fluorescent dye showed a moderate response to the pH change from 1 to 7 in terms of an increase in emitted intensity. The fluorescently labeled particles were able to tolerate an extremely acidic solution (pH 1) but disintegrated within an extremely basic solution (pH 14). The particle‐templated droplets were able to effectively retain the disintegrating particle and the fluorescent signal at pH 14, indicating completely segregated compartments. This article is protected by copyright. All rights reserved

Synthesis and Size Control of CaHPO4 Particles in a Two-Liquid Phase Micro-Mixing Process

Micron-Size Functional Uniform Pmma Particles by Dispersion Copolymerization in Polar Media

Controllable Synthesis of (nh4)fe2(po4)2(oh)·2h2o Using Two-Step Route: Ultrasonic-intensified Impinging Stream Pre-Treatment Followed by Hydrothermal Treatment.

Synthesis of α-calcium sulfate hemihydrate submicron-rods in water/n-hexanol/CTAB reverse microemulsion

Synthesis of Size-Controlled Acid-Resistant Hybrid Calcium Carbonate Microparticles As Templates for Fabricating “Micelles-Enhanced” Polyelectrolyte Capsules by the LBL Technique

Controlling Pore Size and Wettability of A Unique Microheterogeneous Copolymer Film with Porous Structure

Manipulating The Generation Of Uniform O/W And W/O Emulsions Using Microfluidic T-Junction

Liquid–liquid Two‐phase Flow in Pore Array Microstructured Devices for Scaling‐up of Nanoparticle Preparation

Manipulating T-Junction Chip for the Generation of Uniform O/W and W/O Emulsions

Controllable Preparation of Monodispersed Calcium Alginate Microbeads in a Novel Microfluidic System

Preparation of ultrafine calcium carbonate particles with micropore dispersion method

Controllable Preparation of Sio2 Nanoparticles Using A Microfiltration Membrane Dispersion Microreactor

Tailoring the Droplet Size of Pickering Emulsions by PISA Synthesized Polymeric Nanoparticles

Particle Size Control in Sol-Gel Synthesis of Nano Hydroxyapatite

Preparation of Large-Sized Hydroxyapatite Single Crystals Using Homogeneous Releasing Controls

Controlled synthesis and transformation of nano-hydroxyapatite with tailored morphologies for biomedical applications

Liquid-gas Dual Phase Microfluidic System for Biocompatible CaCO3 Hollow Nanoparticles Generation and Simultaneous Molecule Doping.

Size-Controlled Preparation and Behavior Study of Phospholipid-Calcium Carbonate Hybrid Nanoparticles.

Enhancement of Mixing and Mass Transfer Performance with a Microstructure Minireactor for Controllable Preparation of CaCO3 Nanoparticles

Fabrication of Crescent Shaped Microparticles for Particle Templated Droplet Formation

Millimeter-Size Pickering Emulsions Stabilized with Janus Microparticles.