Abstract:The regulation for the lead discharge in the environment was strengthened, in Japan, the standards 0.01 mg/I or less has been in force from April 2003. In order to meet the new standard, two technologies for reduction of lead dissolution into the drinking water have been developed in Japan; substitution of lead free copper alloys for lead bearing bronze (JIS-CAC406) and introduction of surface treatment technology. This technological trend was shortly reviewed. For development of lead free copper alloy casting, mechanical properties, castability and machinability of various lead free alloy castings were examined. Trial alloys used were commercially available ones such as the lead free bronze containing Bi, the lead free bronze containing Bi-Se, the lead free bronze containing Bi-Sb and the lead free brass containing Si. Mechanical properties of alloys were dependent on the pouring temperature and castings thickness and were generally less than those of tin bronze castings (JIS-CAC406, Cu-5 wt% Sn-5 wt% Zn-5 wt% Pb). The machinability of the lead free bronze containing Bi and Se was better than that of the lead free bronze castings containing Bi and Bi-Sb. But was still 10 to 15 % less than that of JIS-CAC406. In a lead free alloy substituted by Bi, adjustment of tin, zinc and bismuth contents was attempted and in the Bi-Se system, the adequate adjustment, for bismuth and selenium contents and also for tin, zinc and bismuth contents, was attempted. New alloy in which the mechanical properties sufficiently satisfy the standard for JIS-CAC406 is developed.

Chemical Composition of New Copper Alloys for Machining and Its Effect on Their Susceptibility to Corrosion Cracking

Investigation of fracture mechanical properties of a brass alloy with microstructural variations

Effects of Microstructure on the Stress Corrosion Cracking Behavior of Nickel-Aluminum Bronze Alloy in 3.5% NaCl Solution

Effects of Al addition on corrosion behavior and mechanical property of high-strength and high-elasticity Cu-20Ni-20Mn-0.3Nb-0.3Cr-0.3Zr alloy

Influence of the Material Production Route on the Material Properties and the Machinability of the Lead-Free Copper-Zinc-Alloy CuZn40 (CW509L)

Effect of Al Content on Corrosion Resistance of Cu-22.7Zn-Al-1.0Ni Brass

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Compositional Design and Thermal Processing of a Novel Lead-Free Cu–Zn–Al–Sn Medium Entropy Brass Alloy

Effect of Silicon Addition on Friction and Wear Behaviour of High Tensile Brasses

Machinability and microstructure of some common non-ferrous metals and alloys

MODIFICATION OF THE SURFACE OF COPPER ALLOYS WITH ALUMINUM IN THE CONDITIONS OF SELF-PROPAGATING HIGH-TEMPERATURE SYNTHESIS

Stress Corrosion Cracking of 60/40 Cupro-Nickel Alloy: Fractography and Chemical Analysis

Corrosion Behaviors of Nanocrystalline and Conventional Polycrystalline Copper

Synergistic effect of water solubility sulfhydryl compound and rare-earth ions on the microstructure, composition, and corrosion resistance of brass

Corrosion evaluation of Al-Cu-Mn-Zr cast alloys in 3.5% NaCl solution

Stress corrosion in copper–nickel alloys: influence of ammonia

Influence of the sintering method on microstructure and microhardness of AlCuNiSnZn-based high-entropy brasses and bronzes obtained by powder metallurgy

Development Of Lead Free Copper Alloy Casting; Mechanical Properties, Castability and Machinability

Effect of Zn/Mg/Cu Additions on Hot Cracking Tendency and Performances of Al-Cu-Mg-Zn Alloys for Liquid Forging

Influences of Fe, Ni and Cu on corrosion resistance of AXJ530 magnesium alloy

High-strength, ductility and corrosion-resistant in a novel Cu20Ni20Mn0.3Cr0.3Al alloy