Data Acquisition Based on the LM331 and PIC16F73 SCM

刘金华,皮大能,程彩云

DOI: https://doi.org/10.3969/j.issn.1003-7241.2009.11.031

2009-01-01

Abstract:This paper introduces a data acquisition system based on the PIC16F73 SCM,where the V/F converter LM331 chip is used as an A/D converter.The hardware and software of the system are also introduced.The circuit is simple,the cost is low,and the conversion accuracy of the system is high.

What problem does this paper attempt to address?

A Front-End Circuit With 16-Channel 12-Bit 100-Ksps Rc-Hybrid Sar Adc For Industrial Monitoring Application

Zhelu Li,Jianxiong Xi,Lenian He,Kexu Sun

DOI: https://doi.org/10.1109/APCCAS.2016.7803970

2016-01-01

Abstract:A front-end circuit with 16-channel 12-bit 100-kSps RC-hybrid successive approximation register (SAR) analog-to digital converter (ADC) for industrial monitoring application is presented. The front-end circuit can process a wide range input voltage as large as 10 V which is beyond the supply voltage, with the help of voltage divider preceding an analog multiplexer. A programmable gain amplifier (PGA) is used to convert different input voltage ranges into a same one. A RC hybrid digital-to analog converter (DAC) is employed in SAR ADC to avoid calibration requirement for the bridge capacitor which is usually needed for a split capacitor SAR ADC architecture. Serial peripheral interface (SPI) is integrated in the design for communication and configuration. The prototype circuit fabricated in a 0.18 um 3.3 V CMOS process shows the measured DNI, and IN1, within-0.821+0.68 LSB and-0.851+0.82 1,SR, respectively. The circuit consumes 2.04 mVV with a 3.3 V supply voltage. The whole chip occupies an area of 1.844 x 1.387 mm(2).
Research and Implementation of A Low-power High-linearity Audio ΣΔ ADC In 65nm Process

曹天霖,孙颖,韩雁,梁国,廖璐,罗豪

2013-01-01

Abstract:We designed an audio ΣΔ ADC which has low power consumption and high linearity.The proposed ΣΔ ADC contains a 2-1 cascaded 1-bit ΣΔ modulator and a low-power,area-efficient digital decimation filter which is designed using RAM and ROM.This chip has been implemented in SMIC 65nm mixed-signal 1P8M CMOS standard silicon process,and the die area is 0.581mm 2.Experiment results shown that 90dB signal to noise plus distortion ratio(SNDR) and 93dB dynamic range(DR) are achieved within 22.05kHz audio band,at 5M Hz sample rate.The ADC’s power dissipation is 2.2mW under 1.2V supply voltage,which means that this chip obtains high-performance and low-power at the same time.
Design of a Novel 8-Bit 0.35-&Amp;#x00b5;m BiCMOS Pipelined ADC

Guang Xi,Hongxia Liu,Xiaopeng Yu

DOI: https://doi.org/10.1109/edssc.2009.5394248

2009-01-01

Abstract:The pipelined ADC can keep high speed and low power consumption when it achieves high conversion accuracy, it can compromise between speed, conversion accuracy, power consumption and chip area. It is very suitable to be used in system integration and portable devices. This paper presents a novel pipelined analog-to-digital converter (ADC). Based on 0.35 μm BiCMOS process, the design is verified using the sample frequency of 250 MHz. The results show that signal to noise ratio (SNR) and Spurious Free dynamic range (SFDR) can reach 46-dB and 64.8-dB respectively. The power consumption of the key A/D circuit is 118 mW when the supply voltage is 3.3 V.
A Low-Power Inverter-Based ΣΔ Analog-to-digital Converter for Audio Applications

XiaoPeng Liu,Yan Han,XiaoXia Han,Hao Luo,Ray C. C. Cheung,TianLin Cao

DOI: https://doi.org/10.1007/s11432-013-4999-y

2014-01-01

Science China Information Sciences

Abstract:This paper presents a design for a low-power, high-resolution audio ΣΔ analog-to-digital converter (ADC) based on a novel gain-boost class-C inverter. The gain-boost class-C inverter behaves as a sub-threshold amplifier, thereby minimizing power dissipation. The proposed ADC chip is fabricated in a SMIC 65-nm CMOS process with a die area of 0.63 mm2. With 1.2 V of supply voltage, the ADC chip achieves a peak signal-to-noise-plus-distortion-ratio (SNDR) of 92 dB and a dynamic range (DR) of 97 dB over the 20 kHz audio band, consuming only 1.13 mW. These results make the ADC particularly suitable for portable electronics applications.
Data Acquisition and Analysis System Based on AC1078 and Virtual Instrument Workbench

Zhou Wei-lin,Yang Hua-yong,Li Qing-feng

DOI: https://doi.org/10.3969/j.issn.1003-0107.2006.06.005

2006-01-01

Abstract:A data acquisition system based on virtual instrument software LabVIEW and domestic data acquisition card AC1078 is introduced. The driver of AC1078 with LabVIEW and the procedure of signal analysis and processing are described in detail, and the experimental results are given as well.
Design of a Data Acquisition System Used in Laser Scanning Diameter Measuring Gauge

WANG BIN,LI XINQIU,ZHANG LISHENG,LIU DAJIANG

DOI: https://doi.org/10.3969/j.issn.1008-0570.2007.19.043

2007-01-01

Abstract:This paper has made an introduction to the design of a data acquisition system used in laser scanning diameter measuring gauge. The main part of the paper includes the mechanism of the whole system, choice of chips, and related design of hardware and software. The system is based on DSP and CPLD and can exert the advantages of both, which has high value in real production.
Design of Control System Based on CPLD and Microcomputer

陈磊,龚瑞昆,张申坤

DOI: https://doi.org/10.3969/j.issn.1674-0262.2008.04.021

2008-01-01

Abstract:Design of data-collected of controlled system based on CPLD and microcomputer in this paper.ADC0808 is A/D transition chip,the conversion precision is 8 bits.Orientation acquisition channels disparts horizontal and pitching direction,and it has error alarm、focal length setting function.Meanwhile data acquiring system has good real-time.This data-collected system is easy implementation,good reliability,high-amplitude portability,so it can be applied to data acquisition system which calls for omnidirectional and high precision implementation.
A 10-bit 30-MS/s 50mW pipelined A/D converter

Xi Chen,Lenian He,Xiaolang Yan

DOI: https://doi.org/10.1109/icasic.2005.1611342

2005-01-01

Abstract:A 10-bit 30-Msample/s pipelined analog-to-digital converter is designed and implemented in a 0.6μm CMOS technology. Sampling capacitors scaling technique is employed to reduce the power dissipation. The digital correction technique is used to relax the offset requirement of the comparators. A sample-and-hold amplifier (SHA) is also used to improve the signal-to-noise and distortion ratio (SNDR) performance and the linearity of ADC. The simulation and experiment results reveal that the ADC designed with this method achieves the SNDR of 58dB or the ENOB of 9.34 at full speed of 30MHz when input frequency is 7MHz. Furthermore, the ADC consumes only 50mW power at 5V supply voltage with a low power operational transconductance amplifier (OTA) and the dynamic comparators. © 2005 IEEE.
Data Acquisition System Based on QuickUSB

Li Liang,Gong Guanghua

DOI: https://doi.org/10.3969/j.issn.1009-623X.2011.07.012

2011-01-01

Abstract:This paper introduces a DAQ(Data Acquisition) system design of communication between PC and FPGA based on the QuickUSB module.The module which uses the CY7C68013A chip is a high-speed USB interface module produced by Bitwise Company.The module is very convenient for developing MCU and communication between equipment and PC.
Hardware Design of TMS320VC5410 Based Data Acquisition System

Wu Yinqin,Wang Min,Li Wanping,Zhang Jian

DOI: https://doi.org/10.3969/j.issn.1672-4321.2005.04.017

2005-01-01

Abstract:This paper advances a design of data acquisition system based on DSP TMS320VC5410 chip and gives the total design project of the system and the detailed hardware circuit.The paper includes: the design of system′s manual reset circuit,the control of CPLD in DSP data acquisition system,the connection between DSP and A/D chip.The architecture of circuit is clear,and the circuit is simple and easy to realize.
Design of PIC12F675 Microcontroller Based Data Acquisition System for Slowly Varying Signals

N. Monoranjan Singh,K. C. Sarma

DOI: https://doi.org/10.48550/arXiv.1207.2060

2012-07-09

Hardware Architecture

Abstract:The present paper describes the design of a cost effective, better resolution data acquisition system (DAS) which is compatible to most of the PC and laptops. A low cost DAS has been designed using PIC12F675 having 4-channel analog input with 10-bit resolution for the monitoring of slowly varying signals. The DAS so designed is interfaced to the serial port of the PC. Firmware is written in Basic using Oshonsoft PIC IDE and burn to the microcontroller by using PICkit2 programmer. An application program is also developed using Visual Basic 6 which allows to display the waveform of the signal(s) and simultaneously the data also can be saved into the hard disk of the computer for future use and analysis.
Design and Implementation of Sensor Data Recording System

干开峰,王俊,汪济洲

DOI: https://doi.org/10.3969/j.issn.1673-8012.2012.05.015

2012-01-01

Abstract:A new sensor data recording system applied in the industrial field is designed.The hardware uses the high resolution,wide dynamic range 16 bit ∑-Δ chip AD7705 to acquire the sensor data,AD7705 links the microcontroller S3C2440A by SPI bus.Its software uses Linux as embedded operating system,and graphical programming language QT is chosen to design the application.The system is applied to the auto spring elastic testing system,acquiring directly the elastic sensor data,real-time displaying and controlling through the touch screen,meeting completely the high precision demands in the industrial field,having high engineering value in the other fields such as environmental monitoring.
18-Bit A/D Converter AD7674 and Its Application

朱志伟,周志光,刘琼

DOI: https://doi.org/10.3969/j.issn.1674-6236.2010.04.053

2010-01-01

Abstract:In consideration of the higher and higher requirement of data acquisition precision and speed on the ultrasonic measuring distance system recently,at the same time,the simple interface circuit and high reliability was also required,a high-speed data acquisition system used in collecting ultrasonic echo signals was designed and implemented.This system takes the master-control unit with TMS320F2812,takes AD7674 as the high-speed ADC,takes the data transmission con-nection by SPI.Through the research of TMS320F2812 and the AD7674 SPI succession and controls register,it gave the method of disposing the SPI pattern correctly and the controlled process,and solved the critical path of the signal integrity problems.Actual trial shows that in 40kHz ultrasonic ranging system,the error is not more than 2mm,the blind controlled is less than 1cm,it meets the high-precision ultrasonic echo ranging system signal acquisition needs.
An A/D Converting Technology with High Precision,Low Cost and Multiple Measuring Range

Jianrong Yuan,Jianxiang Jin,Yuhui Zhang

DOI: https://doi.org/10.3969/j.issn.1000-0380.2006.08.022

2006-01-01

Abstract:The factors that impact the accuracy and stability of traditional dual-slope integrating A/D converter are analyzed.The operational principle and circuit implementation of MCU-controlled A/D converting technology that eliminate those impactions are introduced.This converting technology assures the accuracy and stability of conversion of analog signal inputs in multiple measuring range by low cost measures,and easy implementation of electrical isolation with high cost effectiveness.It can be widely used for digital measuring instruments and industrial data acquisition.
Data acquisition system based on LabVIEW for array sensors

Zhang Xin,Li Dongmei,Huang Yuanqing

DOI: https://doi.org/10.3321/j.issn:0254-3087.2006.z2.156

2006-01-01

Abstract:This paper describes a data acquisition and display system based on LabVIEW platform and AT89S51 Microcontroller, which communicate with each other via RS232 interface, using user-defined communication protocol to ensure communication efficiency and stability. The system adopts MAX197 A/D converter, which acquires 0～+ 10V voltage signals through 6 analog input channels with 12-bit resolution. And the MCU is programmed with Assembly Language. LabVIEW carries out the management tasks, including the data acquisition control, Serial Port Communication control, display and storage of available data. The system, which has low cost and good performance, has been tested and reflects easy operation, good stability and reliability.
Design of Signal Acquisition and Processing System Based on TMS320F2812 and LabVIEW for FAIMS

Li-xin GAO,Fei TANG,Xiao-hao WANG

DOI: https://doi.org/10.3969/j.issn.1000-8829.2012.12.006

2012-01-01

Abstract:To achieve a miniaturized and portable design of FAIMS,the detection system uses TMS320F2812 and LabVIEW which runs under Windows CE platform as the core of the signal acquisition and processing system. TMS320F2812 controls every circuit module of the system to produce PWM signals which drives RF power and compensation voltage with the accuracy of 0.01 V.Meanwhile,TMS320F2812 controls A/D chip which contributes to precise collection of compensation voltage and weak current.TMS320F2812 communicates with LabVIEW in real-time through the serial port.After a series of data processing,the acquisition accuracy of weak current is 0.1 pA,and the acquisition accuracy of compensation voltage is 0.01 V.
Design of Multi-channel High-speed Data Acquisition System Based on AD7828 and TMS320F206

蔡钦涛,方水良

DOI: https://doi.org/10.3969/j.issn.1004-373x.2003.23.008

2003-01-01

Abstract:8b highspeed AD converter AD7828 has the speed of 50 kHz per channel This paper introduces its principle of working and the interface scheme between AD7828 and TMS320F206,and AM29F040B120PC At last some notices is given about the designing process of multichannel highspeed data acquisition system
The subsystem of data acquisition for 60Co container inspection system

王立强,李富荣,吴志芳,周立业,郑沅水

DOI: https://doi.org/10.3969/j.issn.0258-0934.2001.01.007

2001-01-01

Abstract:This paper presents a data acquisiti on subsystem for 60Cocontainer system. This system consists of receiving data card, preamplifier units and , ADC units. The main circuit isintroduced and we obtain image with good quality by using this system.
A Main Amplifier Circuit and Data Acquisition System for Charged Particle Detector Array

HAO Rui,GE Yucheng

2011-01-01

Nuclear Techniques

Abstract:The charged particle detector array has huge amounts of signal and needs high counting rate.To meet the requirements,a main amplifier and analog-to-digital conversion circuit based on high-speed op-amp chips and ADC chip was designed.A 51-MCU was used to control the circuit of ADC and the USB communication chip.The signals were digitized and uploaded by the MCU-ADC-USB circuit.The whole system has a compact hardware structure and a reasonable controlling software,which meet the design requirements.
A Data Acqusition System Based on DSP and USB

JIANG Chao,LI Pei-yu

DOI: https://doi.org/10.3969/j.issn.1001-3881.2005.01.057

2005-01-01

Abstract:The structure of a data acquisition system based on DSP and USB chips was described.The interface between different modules was introduced,and the design of firmware used in USB was described.

Data Acquisition Based on the LM331 and PIC16F73 SCM

A Front-End Circuit With 16-Channel 12-Bit 100-Ksps Rc-Hybrid Sar Adc For Industrial Monitoring Application

Research and Implementation of A Low-power High-linearity Audio ΣΔ ADC In 65nm Process

Design of a Novel 8-Bit 0.35-&Amp;#x00b5;m BiCMOS Pipelined ADC

A Low-Power Inverter-Based ΣΔ Analog-to-digital Converter for Audio Applications

Data Acquisition and Analysis System Based on AC1078 and Virtual Instrument Workbench

Design of a Data Acquisition System Used in Laser Scanning Diameter Measuring Gauge

Design of Control System Based on CPLD and Microcomputer

A 10-bit 30-MS/s 50mW pipelined A/D converter

Data Acquisition System Based on QuickUSB

Hardware Design of TMS320VC5410 Based Data Acquisition System

Design of PIC12F675 Microcontroller Based Data Acquisition System for Slowly Varying Signals

Design and Implementation of Sensor Data Recording System

18-Bit A/D Converter AD7674 and Its Application

An A/D Converting Technology with High Precision,Low Cost and Multiple Measuring Range

Data acquisition system based on LabVIEW for array sensors

Design of Signal Acquisition and Processing System Based on TMS320F2812 and LabVIEW for FAIMS

Design of Multi-channel High-speed Data Acquisition System Based on AD7828 and TMS320F206

The subsystem of data acquisition for 60Co container inspection system

A Main Amplifier Circuit and Data Acquisition System for Charged Particle Detector Array

A Data Acqusition System Based on DSP and USB