Abstract:Amorphous 2Mg–Fe+xwt.% Ni alloys were synthesized by mechanical alloying of Mg and Fe elemental powders. Two kinds of ball-milling atmospheres, namely, (1) under argon and (2) first under argon and then in tetrahydrofuran (THF), were examined in this study. The effects of the Ni addition and ball-milling time and atmosphere on the microstructure and electrochemical properties of the prepared alloys have been investigated systematically. The results show that the ball-milled (2Mg–Fe) nickel-free mixture still maintains Mg and Fe elemental phases, and its discharge capacity is only 19.2mAhg−1. The Ni powder addition is advantageous for the formation of Mg–Fe amorphous structure and for the improvement of the electrochemical properties of the alloys. For the alloys milled under argon, with the Ni content x increasing, the discharge capacity of the alloys increases first and then decreases, and reaches a maximum value of 455.3mAhg−1 as x=100. With the milling-time extending, the discharge capacity of the alloy increases first and then decreases too. For the alloys milled under argon and then in THF, the alloys exhibit higher degree of amorphorization, bigger specific surface area and more active surfaces, and thus have better electrochemical properties than those milled under argon. With the Ni increasing, the discharge capacity increases from 249.7mAhg−1 (x=50) to 565.2mAhg−1 (x=150) and then decreases to 497.9mAhg−1 (x=200), and the exchange current density I0 increases from 104.8mAg−1 (x=50) to 251.1mAg−1 (x=200), which is consistent with the variation of the HRD of the alloy electrodes in the investigation range.

The Influence of Ball Milling Process on Formation and Electrochemical Properties of Amorphous MgNi Hydrogen Storage Alloys

The Electrochemical Evaluation of Ball Milled MgNi-based Hydrogen Storage Alloys

Mechanical Ball Milling Preparation and Electrochemical Hydrogen Storage Properties of Amorphous Mg-Fe Composites

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

An electrochemical investigation of mechanical alloying of MgNi-based hydrogen storage alloys

Influence of Ball-milling with Ni Powder on the Phase Structure and Electrochemical Hydrogen Storage Properties of Mg17Al12 Alloy

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

Microstructure and electrochemical properties of amorphous composites of ball-milled Mg2Ni0.95Sn0.05 + x wt% Ni

Microstructure and electrochemical properties of amorphous Mg-Fe-Ni hydrogen storage electrode material

Preparation of Mg2Ni Hydrogen Storage Alloy Materials by High Energy Ball Milling

Enhanced Electrochemical Performance of Mg2ni Alloy Prepared by Rapid Quenching in Magnetic Field

Microstructures and hydrogen storage characteristics of nanocrystal/amorphous Mg17Al12 alloy prepared by ball-milling

Grain Refining Effect of Magnetic Field on Mg2ni0.8mn0.2 Hydrogen Storage Alloys During Rapid Quenching

Influence of Ball-Milling with Cu Powder on Electrochemical Properties of V-based Solid Solution Type Hydrogen Storage Alloys

Hydrogen Storage Properties of La1.8Ca0.2Mg14Ni3 Alloy Prepared by Ball Milling in Different Milling Environments

Effect of ball milling on the structure and electrochemical hydrogen storage properties of a RE-Mg-Ni alloy

Effect of ball-milling time on the electrochemical performance of ball-milled LaMg11Ni+200wt% Ni composite

On the Preparation of Amorphous Mg–Ni Alloys by Mechanical Alloying

Effect of Ball Milling Time on Microstructure and Hydrogen Storage Properties of Nd5Mg41Ni Alloy

Hydrogen Storage Properties of La2Mg16Ni Alloy Modified by Ball Milling in Benzene

Hydriding Behavior of Magnesium-Based Hydrogen Storage Alloy Modified by Mechanical Ball-Milling