Abstract:The 2195 Al-Li alloy, as one of the representative third-generation Al-Li alloys, has extensive applications in lightweight aerospace structures. In this paper, the anisotropy in mechanical properties and microstructure evolution of 2195 Al-Li alloy sheets were investigated under a strain rate of 0.01, 0.1, 1 s-1 and a temperature of 440 and 500 °C. Experimental results showed that the hot tensile properties of the 2195 Al-Li alloy sheet exhibited a strong dependence on loading directions. The peak stress (PS) and elongation (EL) along the rolling direction (RD) were larger than the transverse direction (TD). For the tests carried out at 440 °C-1 s-1, the PS values of the sheets stretched along the RD and TD are 142.9 MPa and 110.2 MPa, respectively. And, most of the PS anisotropy values are larger than 15%. The anisotropy in EL is less significant than in PS. All the differences are about 10%. Moreover, dimples in the samples stretched along RD were more and deeper than those along TD at 440 °C. The fracture morphology along RD and TD were similar, and both were cleavage fractures at 500 °C. Particularly, the fractions of high angle grain boundaries (HAGBs) along TD were all about 5% larger than those of RD. And, there were more small-sized continuous dynamic recrystallization (CDRX) grains inside the initial grains and discontinuous dynamic recrystallization (DDRX) grains featured with the local bulge of grain boundaries along TD. This was due to the smaller average Schmid factor and the vertical EL trend of the initial grains when the samples were stretched along TD. A model of grain evolution during the dynamic recrystallization (DRX) along RD and TD was proposed based on EBSD results. The Schmid factor and banded structure had a more prominent effect on the hot ductility of the 2195 Al-Li alloy compared with the degree of DRX, thus presenting a higher EL and better hot ductility along RD.

The Effect of Texture on the Serrated Flow in Peak-Aged 2090 Al-Li Alloy

Serrated Flow Behavior in 2090 Al–Li Alloy Influenced by Texture and Microstructure

Serrated Flow Behavior in 2090 Al-Li Alloy

The effect of temperature on the serrated flow in AA5456 alloys

Quasi-static and dynamic response, and texture evolution of two overaged Al 7056 alloy plates in T761 and T721 tempers: Experiments and modeling

Serrated Flow Behavior in Commercial 5019 Aluminum Alloy

Influence of microstructural and crystallographic inhomogeneity on tensile anisotropy in thick-section Al-Li-Cu-Mg plates

Effect of Solution Treatment on the Inverse Dynamic Strain Aging of A Ni-Co Base Superalloy

Effects of microstructure on tensile properties of AA2050-T84 Al-Li alloy

Microstructure evolution and mechanical properties of Al-Cu-Li alloys with different rolling schedules and subsequent artificial ageing heat treatment

Serrated Flow and Tensile Properties of a Mg–Gd–Zn Alloy

Effect of Initial Orientation on the Anisotropy in Microstructure and Mechanical Properties of 2195 Al-Li Alloy Sheet during Hot Tensile Deformation

The Tensile Properties and Serrated Flow Behavior of A Thermomechanically Treated Cocrfenimn High-Entropy Alloy

Effect of Microstructure on High Cycle Fatigue Behavior of Al-Li Binary Alloy

Evolution of Microstructures and Textures of 7050 Al Alloy Hot-Rolled Plate During Staged Solution Heat-Treatments

Effect of asymmetric rolling and subsequent ageing on the microstructure, texture and mechanical properties of the Al-Cu-Li alloy

A study 0f serrated plastic flow behavior in an aluminum-lithium binary alloy

Tailoring texture in a near-α titanium alloy: Insights from strain paths and cooling rate influences

Serrated Flow Behavior in Al6xn Austenitic Stainless Steel

Effect of Solute Concentration on the Serrated Flow in Solution-Treated Al–4%Cu Alloys

Strain Hardening and Tensile Behaviors of Gradient Structure Mg Alloys with Different Orientation Relationships