Abstract:Cavitation can be useful in many occasions, for example, it can be adopted to improve the mass and heat transfer of the solution and it can also be used during the wastewater treatment. Among the ways to generate cavitation in hydrodynamic devices, the sharp-edged orifice is often used because it has a simple structure and the tube that has multi-holes orifice plate is more likely to generate cavitation. In this paper, experiment and computational fluid dynamic (CFD) method are carried out, the flux of the test tube is recorded during the experimental process, and the cavitation model used in the numerical study is validated by comparing the simulated results with the experimental results, then triangular, rectangular, and circular shape of holes and different kinds of distributions of holes such as circular and rectangular distributions are numerically studied. The vapor volume fraction is visualized to find out the effects of holes shape and arrangement on cavitation intensity. Besides, study focusing on the inlet pressure is achieved using CFD simulations, and the cavitation number is calculated under different cases to find out their effects on cavitation intensity. It can be concluded from the obtained results that cavitation number decreases with the increase of pressure drop, and under a certain value of pressure drop, the orifice plates with circular holes have the minimal cavitation number and maximal cavitation intensity. When the holes are circular arrangement, the orifice plates with circular and triangular holes has higher cavitation intensity, and when inlet pressure is large enough, different arrangement and shape of holes barely affect the cavitation intensity.

Study on the Effect of Structure Parameters of Discs and Doughnuts Pulsed Extraction Column on Orifice Coefficient

Hydrodynamics of Φ50 Pulsed Extraction Column with Discs and Doughnuts

Study on Hydrodynamics Characteristics in Discs and Doughnuts Pulsed Extraction Column

Determination of Holdup by Air Purge in Φ50 Mm Discs and Doughnuts Pulsed Extraction Column

On-Line Determination of Pulsed Parameters for Pulsed Extraction Column with Discs and Doughnuts by Air Purge Method

Axial Mixing and Mass Transfer Characteristics of Pulsed Extraction Column with Discs and Doughnuts

Hydrodynamics Characteristics of 30%Tbp-Kerosene/nitric Acid Solution in Discs and Doughnuts Pulsed Extraction Column

Hydrodynamic Characteristics of 30% TRPO-kerosene/nitric Acid Solution in Pulsed Extraction Column

Direct Determination of Flooding in Discs and Doughnuts Pulsed Extraction Column by Air-Purge Method

Effect of Air Capacity and Air Resistance on Measurement of Instantaneous Pressure Drop of Column Weight in Pulsed Extraction Column

Determining Axial Dispersion Coefficients of Pilot-Scale Annular Pulsed Disc and Doughnut Columns

Hydrodynamics and Mass Transfer in a Pulsed Packed Column

Experimental and numerical study of cavitation inside sharp-edged multi-hole orifice plate 1

Hydraulic Performance of an Annular Pulsed Disc-and-Doughnut Column

Effect of Operation Modes on Hydrodynamic Performance of Pilot-Scale Pulsed Disc-and-Doughnut and Pulsed Sieve-Plate Columns: A Comparative Study

Axial Mixing and Mass Transfer Performance of an Annular Pulsed Disc-And-Doughnut Column

A Parametric Study on the Effect of Mixing Chamber for Expansion Work Recovery CO2 Ejector

CFD Simulation of Liquid–Liquid Two-Phase Hydrodynamics and Axial Dispersion Analysis for a Non-Pulsed Disc and Doughnut Solvent Extraction Column

Scale-Up Study on the Performance of Annular Pulsed Disc-And-Doughnut Columns

Investigation on effect of injector orifice diameter on injector atomization and combustion characteristics of pulse detonation combustor

Comparison of the hydraulic characteristics of the 30%TRPO/kerosene―HNO3 and iPr-C[4]C-6/n-octanol―HNO3 systems in an annular centrifugal extractor