Abstract:The solubility parameters of polyacrylonitrile (PAN) and of three different solvents, N, N-dimethylformamide (DMF), N, N-dimethylacetamide, and N-methyl-2-pyrrolidone, as also Flory–Huggins parameters between PAN and these solvents were first calculated, using molecular dynamics simulation. From the simulation results, DMF was chosen as the solvent for PAN in magnetic-field-assisted electrospinning (MFAES). Then, a systematic investigation of the processing parameters, including their interaction and modeling of the degree of fiber alignment, was conducted using a three factor, three-level Box–Behnken design, combined with response surface methodology and quadratic programming. Three independent variables (solution concentration [ X 1 ], ranging from 12% to 14%; voltage [ X 2 ], ranging from 12 to 16 kV; and the distance between two magnets [ X 3 ], ranging from 2 to 3 cm) were consecutively coded as x 1 , x 2 and x 3 at three levels (−1, 0, and 1). The degree of PAN fiber alignment ( Y) was maximized, based on 17 different MFAES experimental data, and a second-order polynomial regression equation was obtained to predict the corresponding results. The significance of independent variables and their interactions was tested by the analysis of variance with 95% confidence limits ( a = 0.05). The standard effects of the independent variables and their interactions on the response were also investigated by preparing a Pie chart. The optimum values of the selected variables were obtained by solving the quadratic regression model and analyzing the response surface contour plots. The optimum coded values of the three test variables were computed as x 1 = 0.35, x 2 = −0.52, and x 3 = 0.15. The experimental conditions at this global point were determined to be X 1 = 13.35%, X 2 = 13.03 kV, and X 3 = 2.58 cm, and the corresponding Y was found to be about 96%.

Spinnability of Polyacrylonitrile Spinning Solution in Composite Solvent

Investigating the Spinnability in the Dry‐jet Wet Spinning of PAN Precursor Fiber

Gel Spinning of Polyacrylonitrile Fibers with Medium Molecular Weight

Effects of Electrospinning Technological Parameters on Diameter of Polyacrylonitrile Insulation Nano-fiber

Solvent selection for polyacrylonitrile using molecular dynamic simulation and the effect of process parameters of magnetic-field-assisted electrospinning on fiber alignment

Study on the Formation Process of Polyacrylonitrile As‐spun Fiber

Fiber Spinning of Polyacrylonitrile Grafted Soy Protein in an Ionic Liquid/DMSO Mixture Solvent

Effect of Coagulation Conditions on the Radial Moduli of Polyacrylonitrile Nascent Fibers

Effects of Moisture Content and Heat Treatment on the Viscoelasticity and Gelation of Polyacrylonitrile/Dimethylsulfoxide Solutions

Study On The Spinnability In Gel Spinning Of Pan Precursor Fiber

Preparation and characterization of pan nanofiber via electrostatic spinning

Electrospinning of Polyacrylonitrile Fibers from Ionic Liquid Solution

Study on the Electrospinnability of Polyvinyl Alcohol Solutions by Using Water/N, N-dimethylacetamide or Water/N, N-dimethylformamide As Solvents

Influence of Alkyl Acrylate Nature on Rheological Properties of Polyacrylonitrile Terpolymers Solutions, Spinnability and Mechanical Characteristics of Fibers

Rheological Study on Thermal-Induced Gelation Behavior of Polyacrylonitrile Solution

Diffusion coefficients of Dimethyl sulphoxide (DMSO) and H2O in pan wet spinning and its influence on morphology of nascent polyacrylonitrile (PAN) fiber

Research on Spinnability of Polyacrylonitrile Solution for Carbon Fibers

PREPARATION OF POROUS POLYACRYLONITRILE ULTRATHIN FIBERS BY ELECTROSPINNING WITH NONSOLVENT INDUCED PHASE SEPARATION

Shear and Extensional Rheology of Polyacrylonitrile Solution: Effect of Ultrahigh Molecular Weight Polyacrylonitrile

Improving the Physical Properties of Nanofibers Prepared by Electrospinning from Polyvinyl Chloride and Polyacrylonitrile at Low Concentrations

Non-Coagulant Spinning of High-Strength Fibers from Homоpolymer Polyacrylonitrile Synthesized via Anionic Polymerisation