Abstract:The possible fracture process of interior texture and its reinforcing mechanism to properties. Polyacrylonitrile (PAN)‐based precursor fibers with different mechanical properties prepared by wet‐spinning and its correlation with microstructure was researched, the primary structural factors that affecting its properties were analyzed. The tensile strength and modulus of precursor fibers increased from 4.63 cN/dtex to 9.16 cN/dtex and 99.09 cN/dtex to 168.92 cN/dtex, respectively, with the increase in crystallinity from 69.29% to 87.84% and orientation degree increased from 83.95% to 93.81%, high performance precursor fibers could be achieved by decrease in the crystallite size and interlayer spacing, these aggregation structure plays a decisive role to the mechanical properties of fibers. The integrality of aggregation structure and properties could reflected by boiling water shrinkage behavior and glass transition temperature from the side. The fracture morphology of fibers with different properties were studied by scanning electron microscope (SEM) and three fracture characteristics were observed, PF1 and PF3 presented the radial extended fracture without microfibril pull out, radial cluster fracture with the pull out of microfibril for PF2, PF4–PF6, together with the axial splitting pattern in PF6, which was revealed by microfibrils/fibrils in longitudinal and transverse combined with solution etching. Precursor fibers with less voids, without serious skin‐core, continuous arrangement, tightly stacked, well‐developed and complete oriented microfibrils/fibrils, exhibited excellent mechanical properties. Possible fracture process was given from the perspective of aggregation structure and microfibrils/fibrils, which become dominant factors determining properties of precursor fibers. Improve the performance could be achieved by regulating surface structure and cross‐sectional shape. As one of the main structural factors that determining properties, by reducing diameter could minimize the numbers and sizes of defects.

Research on Spinnability of Polyacrylonitrile Solution for Carbon Fibers

Numerical Study of Melt-Spinning Dynamic Parameters and Microstructure Development with Ongoing Crystallization

Rheologic behaviors and continuously dry spinning of polyacetylacetonatozirconium fibers

Effect of Solution Concentrations on the Structure and Properties of Nanofibrous Yarns by Blown Bubble-Spinning

Comprehensive research on the correlation between microstructure and mechanical properties of polyacrylonitrile‐based precursor fibers prepared by wet‐spinning

Study on the Rheological Properties of Fluorinated Polyimide Spinning Solution

A Comprehensive Study on the Rheological Properties of Collagen/PVA Spinning Solutions from Acetic Acid Solvent

Spinning solution flow model in the nozzle and experimental study of nanofibers fabrication via high speed centrifugal spinning

Investigation on spinnability of low molecular weight alkaline lignin to fabricate biobased carbon fiber

Investigation into shear-thinning behavior in wet spinning of carbon nanotube fibers modeled by power law viscosity model

Effect of Jet Stretch on Polyacrylonitrile As‐spun Fiber Formation

Effect of Coagulation Bath Concentration on the Structure and Properties of Polyacrylonitrile As-Spun Fibers During Wet-Spinning

Non-Coagulant Spinning of High-Strength Fibers from Homоpolymer Polyacrylonitrile Synthesized via Anionic Polymerisation

Draw-Spinning of Kilometer-Long and Highly Stretchable Polymer Submicrometer Fibers.

Enhancing Asphaltene Spinnability via Polymer Blending

Modeling and characterization of the mechanical properties of nanofiber yarn

Investigation of the rheological response of a bio-liquefied formaldehyde resin-based precursor for electrospinning

Identifying breach mechanism during air‐gap spinning of lignin–cellulose ionic‐liquid solutions

Effect of dispersion time on the microstructural and mechanical properties of carbon nanotube solutions and their spun fibers

Shear Force Fiber Spinning: Process Parameter and Polymer Solution Property Considerations

Effect of Die-Swell Ratio on Polyacrylonitrile As-Spun Fiber Formation