Abstract:High quality lumbers produced from Eucalyptus plantations can be used to make higher value-added solid wood products. Moisture flow affects shrinkage, deformation, and quality of Eucalyptus wood during conventional drying. In this study, 50 and 100 mm long samples were dried using a conventional drying method. The drying curves, drying rate, moisture content (MC) gradient and distribution, moisture flow, and shrinkage during the drying process were investigated. The results show: Drying was much faster in the first 15 h for all samples and became slow as MC decreased. The drying rate above fiber saturated point (FSP) was about 3.5 times of that below FSP for all samples. The drying rate of 50 mm samples above and below FSP is 1.40 and 1.33 times of 100 mm samples; MC gradients are greater in tangential, radial directions, and cross-sections for both samples when the MC is above FSP, especially at an average MC of 50%. MC gradient along the tangential and radial direction depends on the samples size and MC stages. The short samples have much greater MC gradients than the longer samples above FSP. Moisture distributions on the cross-sections of wood coincide with the moisture gradient in the cross-sections. At an average MC of 50%, the moisture distributions of 50 mm are highly uneven, while they are relatively even in the middle of 100 mm samples, and become much more even at the end of the sample. Moisture distributions become even as MC decreases in all of the samples. Water migration directions vary by state of water. In the short samples, most free water migrates more in the fiber direction from the wood center toward the end surfaces, but bound water diffusion becomes weak. The collapse in the 50 mm samples is significantly larger than that in the 100 mm samples, indicating that the collapse is affected by the dimension of the sample.

Preliminary Study on the Conventional Drying Technology of Cyclobalanopsis Glauca

Characterization and Prediction of Mechanical and Chemical Properties of Luanta Fir Wood with Vacuum Hydrothermal Treatment

The Drying Characteristics and Quasi-drying Schedules on Seven Species of Plantation-grown Eucalyptus Wood Based on Solid Wood Products

Biomass and Carbon Storage in an Age-Sequence of Cyclobalanopsis Glauca Plantations in Southwest China

Drying Characteristics of Eucalyptus urophylla × E. grandis with Supercritical CO 2 .

Study On Low-Toxicity Fire-Retardant Treated Technology Of Wood

A New Rapid Drying Method Of 2.5cm-thick Oak Floor Blanks

The Characteristics of Moisture and Shrinkage of Eucalyptus urophylla × E. Grandis Wood during Conventional Drying

A scalable solvent-exchange strategy for the drying of colorless Japanese cedar (Cryptomeria japonica)

A Thermophysical Study on the Freeze Drying of Wooden Archaeological Artifacts

Dewatering characteristics of Juglans mandshurica wood using supercritical carbon dioxide: A comparison with conventional drying

Lumber Drying Stresses and Mitigation of Cross-Sectional Deformation

Study on free shrinkage and rheological characteristics of Eucalyptus urophylla ×E. grandis during conventional drying

Process modeling and simulation of Gmelina arborea (GmW) and Mansonia altissima (MaW) wood drying

Comparison of X-ray Scanning and Slice Methods for Moisture Distribution Measurements when Drying Cunninghamia Lanceolata Plantation Wood

Effect Of Drying Temperature On Colorimetric Change In Plantation-Grown Eucalyptus Wood

Energy Efficiency Performance Enhancement of Industrial Conventional Wood Drying Kiln by Adding Forced Ventilation and Waste Heat Recovery System: A Comparative Study

A cyclic (intermittent) drying schedule for Macassar ebony—the prevention of collapse deformation and the utilization of mechano-sorptive creep gradient

High temperature drying of sawn timber—A review

Optimization of Cold-Air Drying of Apostichopus japonicus and Comparison with Other Drying Methods

Effect of the drying condition on the strength properties of Japanese larch board after vacuum heat treatment