Plastic zone and opening displacement of a propagating crack in a strip

Fan Tian-You,TY FAN

DOI: https://doi.org/10.1016/0013-7944(93)90048-W

IF: 5.4

1993-01-01

Engineering Fracture Mechanics

Abstract:A Dugdale model is presented for a propagating semi-infinite crack in a strip for Modes I and II. The plastic zone size and the crack opening and crack sliding displacements are determined analytically.

What problem does this paper attempt to address?

Plastic Zone and Opening Displacement for an Asymmetrical Fast Propagating Semi-Infinite Crack in A Strip

XC Yang,TY Fan

DOI: https://doi.org/10.1007/978-1-4613-0269-8_26

2000-01-01

Abstract:In this paper, the problems of the generalized Dugdale model for a semi-infinite fast propagating crack asymmetrically in a strip have been discussed. The plastic zone and crack tip opening displacement are given in both cases.
The dugdale model for semi-infinite crack in a strip

Tian-You Fan

DOI: https://doi.org/10.1016/0013-7944(90)90029-G

IF: 5.4

1990-01-01

Engineering Fracture Mechanics

Abstract:This paper suggests a Dugdale model for a semi-infinite crack in a strip. For a small scale yield case, the plastic zone size and the crack opening displacement can be expressed in quite explicit form.
Crack tip opening displacement of a Dugdale crack in a three-phase cylindrical model composite material

H.J. Hoh,Z.M. Xiao,J. Luo

DOI: https://doi.org/10.1016/j.ijengsci.2011.01.004

IF: 7.155

2011-01-01

International Journal of Engineering Science

Abstract:The analytical investigation of the plastic zone size of a crack in three-phase cylindrical model composite material was carried out. The physical problem is simulated as a crack near a circular inclusion (a single fiber) in the composite matrix, while the three-phase cylindrical composite model is used to represent the composite matrix. In the solution procedure, the crack is simulated as a continuous distribution of edge dislocations. With the Dugdale model of small scale yielding, a thin strip of yielded plastic zone is introduced at each crack tip. Using the solution for a three-phase model with a single dislocation in the matrix phase as the Green’s function, the physical problem is formulated into a set of singular integral equations. By employing Erdogan and Gupta’s method, as well as iterative numerical procedures, the singular integral equations are solved numerically for the plastic zone sizes and crack tip opening displacements.
Plastic zone size and crack tip opening displacement of a Dugdale crack interacting with a coated circular inclusion

H. J. Hoh,Z. M. Xiao,J. Luo

DOI: https://doi.org/10.1080/14786435.2010.491806

2010-01-01

Abstract:An analytical investigation on the plastic zone size of a crack near a coated circular inclusion under three different loading conditions of uniaxial tension, uniform tension and pure shear was carried out. Both the crack and coated circular inclusion are embedded in an infinite matrix, with the crack oriented along the radial direction of the inclusion. In the solution procedure, the crack is simulated as a continuous distribution of edge dislocations. With the Dugdale model of small-scale yielding [J. Mech. Phys. Solids 8 (1960) p. 100], two thin strips of yielded plastic zones are introduced at both crack tips. Using the solution for a coated circular inclusion interacting with a single dislocation as the Green's function, the physical problem is formulated into a set of singular integral equations. Using the method of Erdogan and Gupta [Q. J. Appl. Math. 29 (1972) p. 525] and iterative numerical procedures, the singular integral equations are solved numerically for the plastic zone sizes and crack tip opening displacement.
On the plastic zone size and crack tip opening displacement of a Dugdale crack interacting with a circular inclusion

H. J. Hoh,Z. M. Xiao,J. Luo

DOI: https://doi.org/10.1007/s00707-009-0211-2

IF: 2.645

2009-01-01

Acta Mechanica

Abstract:An analytical investigation on the plastic zone size (PZS) of a crack near a circular inclusion has been carried out. Both the crack and the circular inclusion are embedded in an infinite matrix, with the crack oriented along the radial direction of the inclusion. In the solution procedure, the crack is simulated as a continuous distribution of edge dislocations. With the Dugdale model of small scale yielding, two stripe plastic zones at both crack tips are introduced. Using the solution of a circular inclusion interacting with a single dislocation as the Green’s function, the physical problem is formulated as a set of singular integral equations. With the aid of Erdogan and Gupta’s method and iterative numerical procedures, the singular integral equations are solved numerically for the PZS and the crack tip opening displacement. The results obtained in the current work can be reduced to those simpler cases of the Dugdale model.
Penny-Shaped Dugdale Crack in a Transverse Isotropic Medium

X. Y. Li,D. Yang,W. Q. Chen,G. Z. Kang

DOI: https://doi.org/10.1007/s10704-012-9720-4

IF: 2.635

2012-01-01

International Journal of Fracture

Abstract:Analytical results for a penny-shaped crack with a plastic zone at the crack front are given. The crack is embedded in an infinite transversely isotropic elastic medium and is assumed to be subjected to two identical axisymmetric loads on the upper and lower crack faces. The size of the plastic zone at the crack front is determined by applying Dugdale hypothesis to the elasticity results for a penny-shaped crack. The size of the plastic zone is derived in terms of hyper-geometric functions. Expression of the normal stress outside the plastic zone is also given.
A Plastic Crack in a Smectic Liquid Crystal – a Possible Model

Tian You Fan

DOI: https://doi.org/10.1080/09500839.2011.641510

IF: 1.195

2011-01-01

Philosophical Magazine Letters

Abstract:A plastic crack model for smectic A liquid crystals is suggested in this article. The solution for the crack problem is based on the dislocation pile-up principle and the singular integral equation method. From the solution we can determine the size of the plastic zone at the crack tip and the crack tip opening (sliding) displacement, which are parameters relevant to the stability/instability of materials. The results may be useful in developing soft-matter mechanics.
On the Plastic Zone Size and CTOD Study for a Zener–Stroh Crack Interacting with a Circular Inclusion

H. J. Hoh,Z. M. Xiao,J. Luo

DOI: https://doi.org/10.1007/s00707-011-0466-2

IF: 2.645

2011-01-01

Acta Mechanica

Abstract:An analytical solution is given for plastic yielding of a Zener–Stroh crack near a circular inclusion embedded in an infinite matrix. The crack is orientated along the radial direction of the inclusion. In the solution procedure, the crack is simulated as a continuous distribution of edge dislocations. Using the Dugdale model of small-scale yielding, plastic zones are introduced at both crack tips. Using the solution of a circular inclusion, interacting with a single dislocation as the Green’s function, the physical problem is formulated into a set of singular integral equations. With the aid of Erdogan’s method and iterative numerical procedures, the singular integral equations are solved numerically for the plastic zone sizes and crack tip opening displacement. The results obtained in the current work are verified by reduction to simpler cases of the Dugdale model. Various parameters such as the distance, shear modulus ratio, Poisson’s ratio, and loading condition are studied.
Plastic fracture of quasicrystals

T. Y. Fan,L. Fan

DOI: https://doi.org/10.1080/14786430801894536

2008-01-01

Abstract:Elasto-plastic crack solutions for some one- and two-dimensional quasicrystals have been found based on the generalized Dugdale-Barenblatt model. The size of the plastic zone and crack tip opening displacement are determined, from which a plastic fracture criterion for the materials is suggested.
The Dugdale Model for A Semi-Infinite Crack in A Strip of Two-Dimensional Decagonal Quasicrystals

Ling-yun Xie,Tian-you Fan

DOI: https://doi.org/10.1063/1.3589242

IF: 1.469

2011-01-01

Journal of Mathematical Physics

Abstract:The problem of a semi-infinite crack in a strip is useful in materials science and engineering. The paper proposes a Dugdale model for the configuration of two-dimensional decagonal quasicrystals. Through the complex variable method, we obtain the exact solution of the problem. The plastic zone and the crack tip opening displacement and the most important physical quantity, stress intensity factor, can be expressed in quite a simple form.
CRACK PROPAGATION IN POLYCRYSTALLINE ELASTIC-VISCOPLASTIC MATERIALS USING COHESIVE ZONE MODELS

Wu Yan-qing,Zhang Ke-shi

DOI: https://doi.org/10.1007/s10483-006-0411-y

2006-01-01

Applied Mathematics and Mechanics

Abstract:Cohesive zone model was used to simulate two-dimensional plane strain crack propagation at the grain level model including grain boundary zones. Simulated results show that the original crack-tip may not be separated firstly in an elastic-viscoplastic polycrystals. The grain interior’s material properties （e.g. strain rate sensitivity） characterize the competitions between plastic and cohesive energy dissipation mechanisms. The higher the strain rate sensitivity is, the larger amount of the external work is transformed into plastic dissipation energy than into cohesive energy, which delays the cohesive zone rupturing. With the strain rate sensitivity decreased, the material property tends to approach the elastic-plastic responses. In this case, the plastic dissipation energy decreases and the cohesive dissipation energy increases which accelerates the cohesive zones debonding. Increasing the cohesive strength or the critical separation displacement will reduce the stress triaxiality at grain interiors and grain boundaries. Enhancing the cohesive zones ductility can improve the matrix materials resistance to void damage.
Propagating Crack in a Strip: A Study on Exact Analytic Solutions in Closed Form

TY FAN

DOI: https://doi.org/10.1016/0013-7944(91)90154-s

IF: 5.4

1991-01-01

Engineering Fracture Mechanics

Abstract:This paper gives some exact solutions for a propagating semi-infinite crack in a strip; dynamic stress intensity factors are determined in closed form which are exact and found for the first time.
Plastic Zone Correction on a Zener–Stroh Crack Interacting with a Circular Inclusion in Ductile Materials

M. Fan,D. K. Yi,Z. M. Xiao

DOI: https://doi.org/10.1111/ffe.12353

IF: 3.373

2016-01-01

Fatigue & Fracture of Engineering Materials & Structures

Abstract:Elastic-plastic stress analysis on a matrix Zener-Stroh crack interacting with a circular inclusion (fibre) in fibre-reinforced composites has been carried out. The Zener-Stroh crack is initiated near the fibre in the pure matrix. Plastic zone correction is introduced the first time for such a crack-inclusion interaction problem so that the fracture behaviour can be analysed more accurately. To determine the plastic zone sizes, a generalized Irwin model is proposed for the mixed-mode problem where the Von Mises stress yielding criterion is employed. Different to a Griffith crack, a Zener-Stroh crack propagation always occurs from the sharp tip whose relative position to the inclusion has great effect on the elastic-plastic fracture behaviour of the crack. In our study, the plastic zone size (PZS), crack tip opening displacement (CTOD) and effective stress intensity factor (SIF) are evaluated by solving the formulated singular integral equations. Through the numerical examples, the influence of the inclusion (fibre) shear modulus, crack-inclusion distance and the crack sharp tip position on the fracture behaviour of the crack is discussed. It is found that the shear modulus ratio and the crack-inclusion distance have great effect on the normalized values of PZS and CTOD, but the effects highly depend on the crack sharp tip position.
Plastic Zone Affected by Crack Tip Curvature

张培源,张晓敏,严波,彭向和

DOI: https://doi.org/10.3969/j.issn.1000-4939.2004.04.020

2004-01-01

Abstract:A dull crack model, with a circular curve on the tip, was investigated. An elastic solution without crack was taken in the periphery of the crack tip, the line field analysis method was adopted and a method for computing plastic zone forward crack tip was proposed. For a circular disk with radial crack uniformly subjected to tension in outer circular boundary, the relation between size of plastic zone forward crack tip and curvature radio of crack tip was obtained. It is concluded that the relationship between size of plastic zone forward crack tip and curvature radio of crack tip exists, if the size of plastic zone forward crack tip keeps as a constant, the uniform tension in out circular boundary is inverse proportional to the square of outer radius. The former conclusion indicates that there exists limitation when size of plastic zone forward crack tip is regarded as criterion of unstable expanding of a crack, and the latter shows the size effect of strength of a body with crack: strength of a body with crack is inverse proportional to the square of line dimension size.
Application of Cohesive Zone Model in Crack Propagation Analysis in Multiphase Composite Materials

M. Fan,Z. M. Xiao,J. Luo

DOI: https://doi.org/10.1080/15376494.2016.1227495

2016-01-01

Mechanics of Advanced Materials and Structures

Abstract:A nonlinear cohesive stress distribution function is employed by relating the cohesive stress to the cohesive zone size (CZS) and the distance from the crack tip to investigate the elastic-plastic fracture behaviors. A crack-inclusion interaction problem is taken as an example to explore the fracture process in the cohesive zone area. The CZS and crack surface opening displacement are evaluated numerically. It is found that for different cohesive parameter combinations, the normalized CZS and crack surface opening displacements change drastically. By reducing the current model to the famous Dugdale model, the results obtained match well with the existing ones.
Penny-Shaped Dugdale Crack in A Transversely Isotropic Medium and under Axisymmetric Loading

Xiang-Yu Li,Shui-Tao Gu,Qi-Chang He,Wei-Qiu Chen

DOI: https://doi.org/10.1177/1081286512437395

2013-01-01

Mathematics and Mechanics of Solids

Abstract:The present work is concerned with a penny-shaped crack embedded in a transversely isotropic medium and oriented in parallel with the isotropic plane of the latter. Three axisymmetric crack problems are investigated. In the first one, the upper and lower lips of the crack are subjected to a pair of annular opposite pressures. In the second and third problems, two opposite concentrated forces of the same magnitude are applied successively at the upper and lower crack lip centres and at any two points outside the crack and on the axis perpendicular to the crack. Using the basic idea underlying Dugdale's crack model, the extent of the plastic zone is analytically estimated in each of the three cases. In addition, the corresponding crack surface displacement is determined explicitly. Numerical examples are provided to discuss the effects of some geometrical and material parameters involved. Apart from their own usefulness in carrying out some simplified crack analyses, the results obtained in this work can in particular serve as benchmarks for computational fracture mechanics.
Fracture behavior investigation on an arbitrarily oriented sub-interface Zener–Stroh crack

M. Fan,D. K. Yi,Z. M. Xiao

DOI: https://doi.org/10.1007/s00707-014-1271-5

IF: 2.645

2014-01-01

Acta Mechanica

Abstract:The general solution of an arbitrarily oriented sub-interface Zener–Stroh crack is derived with the aid of distributed dislocation methods. The crack problem is formulated as a set of singular integral equations and solved numerically so that the stress intensity factor can be evaluated for any orientation angle. To make the facture analysis more accurate, the plastic zone size (PZS) and the crack tip opening displacement (CTOD) are examined by the generalized Irwin model. The plastic zone area is assumed to follow the von Mises yielding criterion and can be related to the stress intensity factors at the crack tips. Numerical examples are given to demonstrate the influence of various parameters, such as material properties, crack–interface distance and loading ratios, on the normalized PZS and CTOD for vertical and parallel crack cases. It is found that the Zener–Stroh crack becomes easier to propagate when it is located in the “softer” phase of the bi-material structure and parallel to the material interface. If the crack is perpendicular to the interface, it would be much easier for the crack to propagate into the “softer” side of the structure.
Plastic Flow Coupled with a Crack in Some One- and Two-Dimensional Quasicrystals

T Fan,HR Trebin,U Messerschmidt,YW Mai

DOI: https://doi.org/10.1088/0953-8984/16/29/014

2004-01-01

Journal of Physics Condensed Matter

Abstract:An analysis of a group of slip dislocations coupled with a crack dislocation group in some one- and two-dimensional quasicrystals is given. The extent of the plastic zone and the amount of the dislocation slip have been determined in a very explicit form.
On the Plastic Zone Correction of a Zener–Stroh Crack Interacting with a Nearby Inhomogeneity and an Edge Dislocation

M. Fan,Z. M. Xiao,J. Luo

DOI: https://doi.org/10.1007/s00707-015-1458-4

IF: 2.645

2015-01-01

Acta Mechanica

Abstract:The investigation on the interaction among a Zener–Stroh crack, a nearby inhomogeneity/inclusion and an extra edge dislocation has been carried out. A Zener–Stroh crack is formed by pileup of net dislocations. With the existence of a nearby inclusion, an extra dislocation near the crack may be either absorbed into the crack (so the crack grows bigger) or repelled away by the crack and the inclusion. The result depends on the force on the dislocation from the crack and inclusion. In our current study, the plastic zone correction at the crack tips is adopted, where the plastic zone size (PZS) is determined by our newly developed generalized Irwin approach since the stress fields around the crack tips are mixed modes. With the distributed dislocation method, the expressions for the stress intensity factor, PZS and crack tip opening displacement (CTOD) are obtained for different sets of geometric and material parameters. Numerical examples show that when the extra single edge dislocation is located near the sharp tip of the Zener–Stroh crack, the normalized PZS and normalized CTOD become very sensitive to the position of the edge dislocation. It is also observed that the mixed mode problem usually has larger PZS and CTOD comparing to the pure mode I loading problem.
Fracture analysis for a sub-interface Zener–Stroh crack in a bi-material plate under small-scale yielding condition

m fan,d k yi,z m xiao

DOI: https://doi.org/10.1016/j.tafmec.2015.01.003

IF: 4.374

2015-01-01

Theoretical and Applied Fracture Mechanics

Abstract:The fracture behavior of a Zener-Stroh crack near a bi-material interface is investigated under the small-scale yielding condition. The plastic zone area is thus modeled by a modified Dugdale model, in which the Von Mises yielding criterion is applied in the yielding zone. The initial crack problem is formulated into a set of singular integral equations by dislocation method so that the stress intensity factors can be calculated numerically. The yielding zone size or the plastic zone size (PZS) and the crack tip opening displacements (CTOD) at the blunt and sharp tip are evaluated for the current Zener-Stroh crack. Numerical examples are given to show the effects of material properties and crack-interface distance on the normalized PZS and normalized CTOD of the Zener-Stroh crack. It is found that the Zener-Stroh crack is easier to propagate when it locates in the "softer" phase of the bi-material structures. For a Zener-Stroh crack, the crack propagation always starts from the sharp tip. By carrying out the plastic zone correction, failure analysis becomes more accurate thus able to avoid over-estimation in composite structure design and enhance the service life of the structure. (C) 2015 Elsevier Ltd. All rights reserved.

Plastic zone and opening displacement of a propagating crack in a strip

Plastic Zone and Opening Displacement for an Asymmetrical Fast Propagating Semi-Infinite Crack in A Strip

The dugdale model for semi-infinite crack in a strip

Crack tip opening displacement of a Dugdale crack in a three-phase cylindrical model composite material

Plastic zone size and crack tip opening displacement of a Dugdale crack interacting with a coated circular inclusion

On the plastic zone size and crack tip opening displacement of a Dugdale crack interacting with a circular inclusion

Penny-Shaped Dugdale Crack in a Transverse Isotropic Medium

A Plastic Crack in a Smectic Liquid Crystal – a Possible Model

On the Plastic Zone Size and CTOD Study for a Zener–Stroh Crack Interacting with a Circular Inclusion

Plastic fracture of quasicrystals

The Dugdale Model for A Semi-Infinite Crack in A Strip of Two-Dimensional Decagonal Quasicrystals

CRACK PROPAGATION IN POLYCRYSTALLINE ELASTIC-VISCOPLASTIC MATERIALS USING COHESIVE ZONE MODELS

Propagating Crack in a Strip: A Study on Exact Analytic Solutions in Closed Form

Plastic Zone Correction on a Zener–Stroh Crack Interacting with a Circular Inclusion in Ductile Materials

Plastic Zone Affected by Crack Tip Curvature

Application of Cohesive Zone Model in Crack Propagation Analysis in Multiphase Composite Materials

Penny-Shaped Dugdale Crack in A Transversely Isotropic Medium and under Axisymmetric Loading

Fracture behavior investigation on an arbitrarily oriented sub-interface Zener–Stroh crack

Plastic Flow Coupled with a Crack in Some One- and Two-Dimensional Quasicrystals

On the Plastic Zone Correction of a Zener–Stroh Crack Interacting with a Nearby Inhomogeneity and an Edge Dislocation

Fracture analysis for a sub-interface Zener–Stroh crack in a bi-material plate under small-scale yielding condition