Abstract:The ash fusion temperature of coal at high temperature is an important parameter for the efficient and safe operation of coal gasifiers. The equipment of ash fusion temperature was used to measure the ash fusion temperatures of the oxide components composed of SiO2, Al2O3, Fe2O3, MgO, and CaO with different proportions. Five variables composed of Si/Al, Si+Al, Fe2O3, MgO, and CaO were selected to verify the effect of the change on the coal ash fusing characteristics and the range of variables cover most domestic coal ash. Factsage was used to calculate the liquidus temperature of coal ash components, and to obtain the solid phase ratios of each crystal in each slag system and the simulation results are verified by experiments. With the contents of CaO, Fe2O3 and Si/Al increase, the ash fusion temperature gradually decreases while with the content increasing of Si+Al and MgO, the ash fusion temperature of the coal ash gradually increases. The ash fusion temperature varied with the contents of the oxide components and was closely related to the corresponding liquidus temperature, which was always higher than the ash fusion temperature about 200℃. Factsage was also used to predict the crystal compositions of the slag system at different temperatures. It could be concluded that there was no necessary relationship between the transformation of different slag systems with the change of a certain variable, and further analysis was needed for the slag system dominated by a specific factor. In the crystal phase experiment, after the slag was fused, quenching could be performed quickly to maintain the original crystal form at the high temperature. When X-ray diffraction analysis was completed, the precipitation ratios of different crystals at various temperatures could be obtained, which was in good agreement with the simulation results. The differences between the simulation and experimental results were also explored. The effects of different oxide compositions on the slag solidification ratios were investigated. The conclusion of this paper lays a foundation for further analysis of the product and characteristics of the molten state of multi-oxide system, and is of great significance for the optimization design operation of gasifier.

Change of Ash Fusing Characteristic in Char Gasification

Effect of Chemical Compositions on Ash Fusibility Characterization of a Jincheng Anthracite During Combustion and Gasification

Study on Coal Ash Fusion Characteristics with TG-DSC Method

Ash Fusion Characteristics and Mineral Evolvement of Blended Ash Under Gasification Condition

Ash fusion temperature and crystal composition of multi-component coal ash

Ash Fusion Regulation Mechanism of Coal with Low Melting Point and Different Ash Compositions

Study on Ash Fusion Process of Blended Coal by TG-DSC

Experimental study on the effects of residual carbon on ash fusion characteristics of high-alkali Zhundong coal under deep oxygen-staged condition

Effect of Temperature and Pressure on the Mineralogical and Fusion Characteristics of Jincheng Coal Ash in Simulated Combustion and Gasification Environments

The Mechanism of the Ash Fusion Characteristics of Gasification Coke Affected by SiO 2 /al 2 O 3 Ratio and CaO Content in Blending Coals

Ash Fusibility Based on Modes of Occurrence and High-Temperature Behaviors of Mineral Matter in Coals

Study on the Coal Ash Fusibility During Blending Coal Combusition

The Desulfurization Behavior of Mineral Matter in Ash During Coal Combustion at High Temperature

Mineral Conversion of Coal-ash in Fusing Process and the Influence to Ash Fusion Point

Influences of Ash-Existing Environments and Coal Structures on CO2 Gasification Characteristics of Tri-High Coal

Influence of Coal Ash on the Characteristics of Corn Straw Pyrolysis Products.

Decarburization and ash characteristics during melting combustion of fine ash from entrained-flow gasifier

Effect of High Calcium and High Iron Coal on Ash Fusion Characteristics of Petroleum Coke during Cogasification

Modification of Melting Combustion Kinetic Model of Fine Ash from Entrained-Flow Gasifier

Ash-fusion Characteristics of Wheat Straw Lignin and Coal Co-Combustion

Melting Characteristics of Coal Ash and Properties of Fly Ash to Understand the Slag Formation in the Shell Gasifier