Abstract:Perfluoroalkyoxy-substituted cyclohexene oxides(EFPO1 and EFPO2) were obtained by two-step reactions using the dimer and trimer of hexafluoropropylene oxide and 4-cyclohexene-1,2-dimethanol as main raw materials.The structures of as-synthesized products were confirmed by spectroscopy analyses including FT-IR and 1H NMR.These fluoro-epoxides are compatible with the prepolymers such as bisphenol-A diglycidyl ether and ethylene glycol diglycidyl ether,thereby endowing the coatings composed of them with improved hydrophobicity as evidenced by the photoinitiated curing experiments.The preliminary investigation of their UV-curing performance shows that the hydrophobicity increases linearly with increasing fluoro-epoxide content in the composition.As expected,the hydrophobic effect is more pronounced for EFPO2 than EFPO1 at the same conditions,because the former has a longer ferfluoroalkyoxy group.For example,upon addiing 1% mass fraction of EFPO2,the water contact angle of the UV-cured films was 99° and was higher 14° than that found for the films without the fluoro-component,whereas the value for EFPO1-modified films was 87°.When containing 5% EFPO2,high hydrophobic surface was achieved with a water contact angle of 113 for the UV-cured films.In addition,it should be pointed out that the hydrophobic surface can be further improved by heating the UV-cured films at 110 ℃ for 6 h.For the coatings containing 1%~5% EFPO2,the post-heating treatment resulted in a change of the water contact angles from the range 99°~113° to 113°~118°,while the changes were from 87°~100° to 99°~110° for EFPO1 analogs.The thermal migration of fluoro-chains and aggregation on the film surface seems to be responsible for the enhancement in hydrophobicity.Consequently,this new type of fluorine-containing epoxy monomers is expected as the surface modifier used in coatings,inks and release materials.

Synthesis of New Fluorinated Epoxides and Preliminary Investigations on Their UV-curing Properties

Synthesis Of Fluoroalkyl-Modified Polyester And Its Application In Improving The Hydrophobicity And Oleophobicity Of Cured Polyester Coatings

Synthesis and characterization of fluorine-containing polyester based on phthalic anhydride and tetrafluoropropyl glycidyl ether

Synthesis, UV-curing Behavior and Surface Properties of New Fluorine-containing Aromatic Oxetane Monomers

Synthesis of Fluoro-(Meth) Acrylates and Performance of the UV-Curing Films

Synthesis of Perfluorinated Oxetane and Surface Properties of Its Cationic Uv Cured Coating As A Reactive Additive

Synthesis of fluorinated monomer and formation of hydrophobic surface therefrom

Synthesis of Fluorinated Polyester Used for Hydrophobic Coating: Influence of Fluoroalkyl Group Length on Enrichment Behavior

Preparation and fluorine enrichment behavior of fluorinated polyester

The Effect of Oxetane as Active Diluent on Cationic UV Curing System of Fluorine-Containing Epoxy Prepolymer

Synthesis and Cationic Photopolymerization of Fluorine‐containing Vinyl Ether Monomers for the Hydrophobic Films

Fluorinated Modification of Hyperbranched Polyesters Used for Improving the Surface Property of Uv Curing Coatings

Preparation Of Fluoro-Modified Acrylate Copolymer And Hydrophobicity Of Coatings Therefrom

Synthesis and Application of New Types of Fluorinated Oxetanes

Synthesis, Uv-Curing Behavior and Surface Properties of Fluorine-Containing Vinyl Ether Polymers

Syntheses and Properties of Fluorinated Phosphate Acrylates Used for UV-curing Coatings

Synthesis and Properties of Fluorinated Non-Isocyanate Polyurethanes Coatings with Good Hydrophobic and Oleophobic Properties

Fluorination of Epoxy Surfaces by a Physical Method

Modification of Epoxy Coatings with Fluorocontaining Organosilicon Copolymers

Preparation and Surface Properties Study of Novel Fluorine-Containing Methacrylate Polymers for Coating

Fabrication of UV-curable Anti-fouling coating based on fluorinated polyoxetane and long Side-Chain Polysilcone