Abstract:Perfluoroalkyoxy-substituted cyclohexene oxides(EFPO1 and EFPO2) were obtained by two-step reactions using the dimer and trimer of hexafluoropropylene oxide and 4-cyclohexene-1,2-dimethanol as main raw materials.The structures of as-synthesized products were confirmed by spectroscopy analyses including FT-IR and 1H NMR.These fluoro-epoxides are compatible with the prepolymers such as bisphenol-A diglycidyl ether and ethylene glycol diglycidyl ether,thereby endowing the coatings composed of them with improved hydrophobicity as evidenced by the photoinitiated curing experiments.The preliminary investigation of their UV-curing performance shows that the hydrophobicity increases linearly with increasing fluoro-epoxide content in the composition.As expected,the hydrophobic effect is more pronounced for EFPO2 than EFPO1 at the same conditions,because the former has a longer ferfluoroalkyoxy group.For example,upon addiing 1% mass fraction of EFPO2,the water contact angle of the UV-cured films was 99° and was higher 14° than that found for the films without the fluoro-component,whereas the value for EFPO1-modified films was 87°.When containing 5% EFPO2,high hydrophobic surface was achieved with a water contact angle of 113 for the UV-cured films.In addition,it should be pointed out that the hydrophobic surface can be further improved by heating the UV-cured films at 110 ℃ for 6 h.For the coatings containing 1%~5% EFPO2,the post-heating treatment resulted in a change of the water contact angles from the range 99°~113° to 113°~118°,while the changes were from 87°~100° to 99°~110° for EFPO1 analogs.The thermal migration of fluoro-chains and aggregation on the film surface seems to be responsible for the enhancement in hydrophobicity.Consequently,this new type of fluorine-containing epoxy monomers is expected as the surface modifier used in coatings,inks and release materials.

Synthesis of Fluorinated Polyester Used for Hydrophobic Coating: Influence of Fluoroalkyl Group Length on Enrichment Behavior

Synthesis Of Fluoroalkyl-Modified Polyester And Its Application In Improving The Hydrophobicity And Oleophobicity Of Cured Polyester Coatings

Preparation and fluorine enrichment behavior of fluorinated polyester

Synthesis and characterization of fluorine-containing polyester based on phthalic anhydride and tetrafluoropropyl glycidyl ether

Synthesis of fluorinated monomer and formation of hydrophobic surface therefrom

Synthesis and Application Properties of Fluorinated Aromatic Copolymers

SYNTHESIS AND PRELIMINARY PROPERTIES OF A WATER-REPELLENT POLY(ARYLENE ETHER)

Influence of Pendant Fluoroalkyl Segments on Properties of Fluoroethylene and Vinyl Ether Polymers and Their Hydrophobic Coatings

Synthesis and surface properties study of novel fluorine-containing homopolymer and copolymers for coating applications

Synthesis and Properties of Transparent Fluorinated Polyurethane Coatings

Synthesis of New Fluorinated Epoxides and Preliminary Investigations on Their UV-curing Properties

Fluorinated Modification of Hyperbranched Polyesters Used for Improving the Surface Property of Uv Curing Coatings

Preparation Of Fluoro-Modified Acrylate Copolymer And Hydrophobicity Of Coatings Therefrom

Synthesis of A Waterborne Polyurethane-Fluorinated Emulsion and Its Hydrophobic Properties of Coating Films

Study on Synthesis of Fluorinated Acrylate Copolymer and Surface Hydro-Oleophobic Properties of the Copolymer Films

The Microstructure and Surface Characteristics of Fluorine‐based Copolymer Coatings Deposited by the Static Breath Method

Preparation and Surface Properties Study of Novel Fluorine-Containing Methacrylate Polymers for Coating

Synthesis and surface property characterization of polyacrylate with short fluorocarbon side chain

Design and Synthesis of High-Performance Polymers with Short Perfluoroalkyl Side Groups Using an Environmentally Friendly Solvent

Perfluoroalkyl End-Functionalized Oligoesters: Correlation Between Wettability and End-Group Segregation

Hydrophobic Surface Via Coating Fluorinated Homopolymer: Effects of the Surface Etching of Silicon Wafer and Coated Fluoropolymer Amount