Abstract:N-type bismuth telluride (Bi2Te3) thin films were prepared on an aluminum nitride (AlN)-coated stainless steel foil substrate to obtain optimal thermoelectric performance. The thermal co-evaporation method was adopted so that we could vary the thin film composition, enabling us to investigate the relationship between the film composition, microstructure, crystal preferred orientation and thermoelectric properties. The influence of the substrate temperature was also investigated by synthesizing two sets of thin film samples; in one set the substrate was kept at room temperature (RT) while in the other set the substrate was maintained at a high temperature, of 300 °C, during deposition. The samples deposited at RT were amorphous in the as-deposited state and therefore were annealed at 280 °C to promote crystallization and phase development. The electrical resistivity and Seebeck coefficient were measured and the results were interpreted. Both the transport properties and crystal structure were observed to be strongly affected by non-stoichiometry and the choice of substrate temperature. We observed columnar microstructures with hexagonal grains and a multi-oriented crystal structure for the thin films deposited at high substrate temperatures, whereas highly (00 l) textured thin films with columns consisting of in-plane layers were fabricated from the stoichiometric annealed thin film samples originally synthesized at RT. Special emphasis was placed on examining the nature of tellurium (Te) atom based structural defects and their influence on thin film properties. We report maximum power factor (PF) of 1.35 mW/m K2 for near-stoichiometric film deposited at high substrate temperature, which was the highest among all studied cases.

Effect of Hot-Press Treatment on Electrochemically Deposited Antimony Telluride Film

Antimony Telluride Thin Films Electrodeposited in an Alkaline Electrolyte

Ultrasonic-assisted Hot Pressing of Bi2Te3-based Thermoelectric Materials

The Effect of Heat Treatment on Electrodeposited Bi2te3 Thin Films for Thermoelectric Applications

Effect of Heat Treatment on the Property of Cuins2 Thin Film Prepared by Chemical Bath Deposition

Influence of Sputtering Power Density on the Thermoelectric and Mechanical Properties of Flexible Thermoelectric Antimony Telluride Films Deposited by DC Magnetron Sputtering

Hydrothermal Synthesis and Thermoelectric Transport Properties of Impurity-Free Antimony Telluride Hexagonal Nanoplates

Effect of Annealing Temperature on Properties of Co-Sputtered Bi2Te3

Effect of Starting Powder Particle Size on the Thermoelectric Properties of Hot-Pressed Bi0.3Sb1.7Te3 Alloys

Influence of annealing on the structural and electrical transport properties of Bi 0.5 Sb 1.5 Te 3.0 thin films deposited by co-sputtering

Direct Current Treatment Tuning Crystallinity Leading to High-Performance p-Type Sb 2 Te 3 Flexible Thin Films

Effect of Deposition Power on the Thermoelectric Performance of Bismuth Telluride Prepared by RF Sputtering

Texture Development and Grain Alignment of Hot‐Pressed Tetradymite Bi 0.48 Sb 1.52 Te 3 Via Powder Molding

Temperature and Size Effects on Electrical Properties and Thermoelectric Power of Bismuth Telluride Thin Films Deposited by Co-Sputtering

Antimony sulfide (Sb2S3) thin films by pulse electrodeposition: Effect of thermal treatment on structural, optical and electrical properties

High thermoelectric performance achieved in Bi0.4Sb1.6Te3 films with high (00l) orientation via magnetron sputtering

Enhanced power factor of Bi<sub>0.5</sub>Sb<sub>1.5</sub>Te<sub>3</sub> thin films via PbTe incorporating and annealing

Composition-dependent characterization and optimal control of electrodeposited Bi2Te3 films for thermoelectric application

Effects of Si Substrates with Variable Initial Orientations on the Growth and Thermoelectric Properties of Bi-Sb-Te Thin Films

Fabrication, micro-structure characteristics and transport properties of co-evaporated thin films of Bi2Te3 on AlN coated stainless steel foils

Hydrothermally Synthesized and Hot-Pressed Bi-2(Te,Se)(3) Thermoelectric Alloys