Abstract:This paper is intended to introduce an analysis method for thermo-gravimetric study of the rigid polyurethane foam(RPUF) of commercial grade in the atmospheric and nitrogen conditions.The samples we adopted should be heated from the ambient temperature to 800 ℃ at the heating rates of 10 ℃/min,20 ℃/min,40 ℃/min and 50 ℃/min,respectively.In the above said conditions,the RPUF to be tested has to undergo four decomposition stages as is required in the said conditions,whereas the first two stages were mainly supposed to experience the loss of water and small molecules,which are actually not essential for the dominant stages.However,the last two stages are supposed to be of great significance.With the increase of the heating rate,the temperature of the onset decomposition Ton,the temperature at the maximum decomposition rate Tm,and the maximum decomposition rate-(dwt/dt)m,are pushed to the high temperature region.Furthermore,the variations of activation energy with the conversion degree are evaluated by using Flynn-Wall-Ozawa(FWO) isoconversional method.In our study,we have also investigated the reaction model and corresponding kinetic parameters with the multivariate non-linear regression method.The kinetic parameters we have gained demonstrate that the decomposition of RPUF tends to undergo two successive reaction steps both under the atmospheric condition and nitrogen condition.The decomposition of RPUF can be described by Fn→Fn kinetic model under the atmospheric condition while that of RPUF under nitrogen condition can be described by Fn→D3 kinetic model.The kinetic model can further be verified by comparing the activation energy values obtained by FWO method and the multivariate non-linear regression method.Based on the analysis of the reliable kinetic parameters and the reaction models,the lifetime of RPUF under different temperatures can be predicted.It is also very sensitive to temperature variations and prone to the effects of other factors,for example,the decomposition atmosphere,etc.Thus,it can be seen that the present paper can provide useful experimental data for the improvement of classification of the burning behaviors and establishment of the system of the fire prevention codes of the exterior insulation.

Ignition characteristics of commonly used exterior thermal insulation systems with rigid polyurethane foam

Combustion Characteristics Of Commercial Exterior Insulation Materials Under Cone-Radiation Condition

Experimental Study on Fire Characteristics of Building External Thermal Insulation Composite Systems Based on Polystyrene Foam

Experimental study on fire behaviors of external thermal insulation composite system under vertical radiation

Combustion characteristics and fire hazard of polystyrene exterior wall thermal insulation materials

Experimental Study Of Thermal Behavior Of Insulation Material Rigid Polyurethane In Parallel, Symmetric, And Adjacent Building Facade Constructions

Thermal Stability Analysis of the Rigid Polyurethane Foam for the Exterior Insulation

Full-scale Experimental Study on Vertical Fire Spread Characteristics of Different Organic Insulation Systems

Experimental Study on the Width and Pressure Effect on the Horizontal Flame Spread of Insulation Material

Influence of the Permeability of External Thermal Insulation on Concrete Wall Carbonization

Experimental Study on Upward Flame Spread of Exterior Wall Thermal Insulation Materials

Research on the Influence of Environmental Pressure on the Combustion Characteristics and Fire Spread of Building External Wall Insulation Materials

Effect of inorganic additive flame retardant on fire hazard of polyurethane exterior insulation material

Experimental Investigation of Downward Discrete Flame Spread of the Thermoplastic Material in Exterior Insulation Walls: Melt-Flowing and -Dripping

Experimental Study on Downward Flame Spread of Rigid Polyurethane Foam with External Radiation

Diphase Flame‐retardant Effect of Ammonium Polyphosphate and Dimethyl Methyl Phosphonate on Polyisocyanurate‐polyurethane Foam

Thermal Decomposition Kinetics of Rigid Polyurethane Foam and Ignition Risk by A Hot Particle

Optimizing the Composition Design of Cement-Based Expanded-Polystyrene (EPS) Exterior Wall Based on Thermal Insulation and Flame Retardance

Simulation of Fire Spread of Typical External Wall Insulation Materials in High-rise Building

Influence of Aluminum Hydroxide and Expandable Graphite on the Flammability of Polyisocyanurate-Polyurethane Foams

Correlation Study Between Flammability and the Width of Organic Thermal Insulation Materials for Building Exterior Walls