Title Biofunctionalized nanoarrays of inorganic structures prepared by dip-pen nanolithography
A. Zhang,H. Lee,King Li,Z. Mirkin,Hua Zhang,Ki-Bum Lee,Zhi Li,C. Mirkin
2018-01-01
Abstract:A dip-pen nanolithography based strategy for fabricating and functionalizing Au nanostructures on a semiconductor substrate is reported. The generation of arrays of nanoscale features functionalized with inorganic nanoparticles and proteins (rabbit IgG) is reported. In the case of rabbit IgG, the bioactivity of the array was demonstrated by monitoring its reaction with fluorophore-labelled antirabbit IgG. The methodology reported herein points towards ways of making raised optically active and bioactive nanostructures that could prove useful in stamping methodologies or biosensing applications. (Some figures in this article are in colour only in the electronic version) Methods for fabricating nanostructures are essential for developing and capitalizing upon the emerging field of nanoscience. In particular, methods are needed that offer the capability of working with both hard and soft matter on a scale of sub-100 nm to many micrometres. Several methods, such as e-beam lithography [1], ion beam lithography [2a] and nanoimprint lithography [3a] offer one the ability to build hard structures on this scale of length, but they do not allow one to deposit molecule-based nanostructures directly on a surface. Microcontact printing (μCP) [4a] allows one to directly deposit molecules onto a surface in a massively parallel fashion, but it does not allow one to generate structures made of different inks with nanoscale registration capabilities. Dip-pen nanolithography (DPN) [5a] has emerged as a tool that allows one to make multicomponent nanostructures on a surface with near-perfect registration capabilities. Although it does not offer the massively parallel capabilities of photolithography [1] and some of the stamping methods [4a], it has been transformed into a parallel writing tool through the use of cantilever arrays consisting of multiple pens [5c, 6]. This makes DPN a unique tool that can be used to fabricate both hard and soft structures with nanoscale precision. Inorganic nanostructures functionalized with biomolecules are having a major impact in the field of biodiagnostics [7a] and beginning to find use in other areas, including materials synthesis [8a], optics [9a], and electronics [10]. Nanostructures functionalized with oligonucleotides [7a, 11] and proteins [12] have been shown to be particularly useful in the development of high sensitivity and selectivity detection systems for DNA, small molecules, and protein structures. In our previous manuscripts [13], we developed a method for fabricating arrays of Au nanostructures on a SiOx/Si surface based on DPN and wet chemical etching [14a]. Herein, we show how the etched Au nanopatterns, created via this methodology, can be used as templates to adsorb and/or assemble Au nanoparticles and proteins from solution to form functionalized inorganic/biological nanostructures. These structures are potentially interesting for their optical and biological sensing capabilities. In a typical experiment, a substrate suitable for patterning experiments was prepared by thermally evaporating 8–10 nm of Au on a Ti-coated (1 nm) oxidized silicon (∼500 nm of oxide) substrate (pressure < 1×10 -7 Mbar). These fresh Au substrates were then patterned with 16mercaptohexadecanoic acid (MHA) by DPN according to procedures given in the literature [5a, 13]. A MHA-coated tip was prepared by immersing a commercial Si3N4 tip (spring constant = 0.05 N m −1 , TM Microscopes, Sunnyvale, CA) into a 5 mM MHA acetonitrile solution for ∼15 s and then drying it with compressed difluoroethane (Dust-off, Ted Pella, Inc., Redding, CA). The DPN experiments were carried out under ambient conditions (set point = 0.5 nN, 22–24 ◦ C, 30–36% relative humidity) by using an AutoProbe CP AFM (TM Microscopes, Sunnyvale, CA) and commercial lithography software (DPNWrite TM , DPN System-1, NanoInk Inc., Chicago, IL) with a MHA-coated tip. Each DPN dot feature was generated by holding a MHA-coated tip in contact with an Au surface for 0.25 s (figures 1(B), 2(B) and 3(B)) and 3.5 s (figure 4), and each line was generated by moving a MHA-coated tip on an Au surface at a rate of 1 μm s −1 (figures 1(A), 2(A) and 3(A)). The ferri/ferrocyanide etchant used in this experiment was prepared by mixing 0.1 M Na2S2O3, 1.0 M KOH, 0.01 M K3Fe(CN)6 and 0.001 M K4Fe(CN)6 in a 1:1:1:1 (v:v:v:v) ratio. After being patterned with MHA, the Au substrates were immersed in the ferri/ferrocyanide etching solution for ∼20 min under constant stirring to remove the exposed Au areas. Then they were treated with 0.5% aqueous HF (obtained by diluting 48% HF (Aldrich)) for 15–30 s to remove the Ti layers [13] (step A in scheme 1). After rinsing with Milli-Q H2O and drying with N2, the MHA-modified Au nanopatterns of lines and dots were characterized by tapping mode AFM (TMAFM) (Nanoscope IIIa, Digital Instruments, Santa Barbara, CA) (figure 1). The distances between the lines (figure 1(A)) and dots (figure 1(B)) are 2 and 1 μm, respectively. The width of the Au lines (figure 1(A)) and the diameter of the Au dots (figure 1(B)) are ∼60 and 150 nm, consistent with the values given in the literature for similar experiments [13a]. To remove the monolayer ‘etch resist’, the etched substrate was irradiated with a UV lamp (365 nm, 21.7 mW cm− 2 , B-100AP, Fisher Scientific, Pittsburgh, PA) for ∼10 h. It is known that UVirradiation of an alkylthiol-coated Au substrate under ambient conditions results in photooxidation of the surface-bound monolayer and its desorption from the surface, if immersed in the appropriate solvent [15a]. After removing the oxidized MHA SAM by rinsing with water, the fresh Au nanostructures can be functionalized with other thiol-containing molecules (step B in scheme 1). Two kinds of thiol functionalized molecules, 2-aminoethanethiol (HS–C2H4–NH2) (AET) and 1,6-hexanedithol (HS–C6H12–SH) (HDT) (Aldrich), were used to modify these fresh Au nanopatterns. After immersing the Au nanopatterns in a 1.0 mM ethanolic solution of AET or HDT for 24 h, amino (NH2) or thiol (HS)-terminated SAMs formed on the Au nanofeatures. These structures can be used to assemble additional nanostructures by electrostatic or covalent interactions to form Au-nanoparticle arrays (step C in scheme 1). For example, after immersing the array of AET-modified nanostructures into a solution of citrate-stabilized gold nanoparticles (∼15 nm, ∼15 nM) [8b, 16] for ∼10 h, with subsequent rinsing with Milli -Q water, a monolayer of Au particles localized on each of the nanofeatures within the array (figure 2). The TMAFM measured height of the individual Au nanoparticles was ∼15 nm and in excellent agreement with the TEM-measured diameter of Au nanoparticles that comprise the colloid. This observation is also consistent with the conclusion that the MHA monolayers on each of the nanofeatures has been removed and replaced with AET. Magnesium oleate capped Au particles (∼15 nm, ∼10 nM) [17a], were used to modify the SH-rich surface of HDT–SAM modified nanofeatures (figure 3). In both cases, collections of individual Au nanoparticles on the Au nanofeatures are observed with very little nonspecific binding to the underlying silicon oxide