Abstract:In this paper, mechanical properties and microstructures of the cast and extruded Al-xCu-1Li-0.4Mg–1Zn-0.1Zr alloys (x = 2.0, 3.0, 4.0, 4.5, 5.5, 6.5 wt%) were investigated. The results showed that the as-cast micrographs of alloys with different Cu content primarily consist of dendritic α-Al grains, and the intermetallic phases at the grain boundaries were Cu and Zr rich phases. After solution treatment, no recrystallization took place in extruded alloys, and the alloys mainly represented mixed textures composed of <111> and <100> fibers. Cu significantly affected the precipitation behavior of the extruded alloys. Only T1 (Al2CuLi) phases were observed in T6 (aging at 175 °C for 32 h) and T8 (3% pre-strain followed by aging at 150 °C for 32 h) treated alloy with 2 wt% Cu. Further increasing Cu contents (4.5 and 6.5 wt%) enabled the co-precipitation of T1 and θ' (Al2Cu) phases, as well as increased their density. In addition, the microstructures of grain boundaries of alloys with different Cu content showed dramatic differences. T1 phases precipitated at the grain boundaries of alloy containing 2 wt% Cu, while rare precipitation of T1 phases was observed at the grain boundaries of alloy with 6.5 wt% Cu. The yield strength (YS) of the alloys increased with the Cu content and the elongation (EL) showed an opposite trend. A good combination of ultra-high strength (YS = 684 MPa, ultimate tensile strength = 726 MPa) and ductility (EL = 6.3%) was obtained in T8 treated alloy containing 4.5 wt% Cu. The presence of the undesired coarse T2 (Al6CuLi3) phases at the grain boundaries resulted in the premature failure of the high Cu content alloys.

Effects of Cu content on the microstructure and mechanical properties of AZ61 alloy

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Influences of Cu Content on the Microstructure and Strengthening Mechanisms of Al-Mg-Si-<i>x</i>Cu Alloys

Effect of Cu content on microstructures and properties of Al-Mg-Si-Cu alloys

Effect of Cu Content and Zn/Mg Ratio on Microstructure and Mechanical Properties of Al–Zn–Mg–Cu Alloys

Effects of Cu Content and Cu/Mg Ratio on the Microstructure and Mechanical Properties of Al–Si–Cu–Mg Alloys

Effects of Cu Addition on Microstructure and Mechanical Properties of As-Cast Magnesium Alloy ZK60

The microstructures and mechanical properties of a highly alloyed Al-Zn-Mg-Cu alloy: The role of Cu concentration

Effect of Cu Content on Microstructure and Mechanical Properties of Al-Cn-0.4Mg-0.6Ag Alloy

Effect of Cu content on the mechanical properties of an Al–Cu–Mg–Ag alloy

Microstructural characteristics and mechanical properties of cast Al-3Li-xCu-0.2Zr alloy

Effects of Cu Content on Microstructure and Properties of Super-High-strength Al-9.3Zn-2.4Mg-xCu-Zr Alloy

Effects of Cu and Mg Contents on Mechanical Properties of Al-xCu-yMg-0.6Ag Alloy

Effect of Cu on Microstructure, Mechanical Properties, and Texture Evolution of ZK60 Alloy Fabricated by Hot Extrusion−shearing Process

Effects of Cu Content on Microstructure and Mechanical Properties of Rheo-Diecasting Al-6Zn-2Mg-xCu Alloys

Effect of Cu on the Fracture and Exfoliation Corrosion Behavior of Al-Zn-Mg-xCu Alloy

Effects of Trace Cu Addition on the Microstructure and Tensile Properties of ZK60 Alloy

Effects of Cu and Mg content on microstructure and mechanical properties of Al-Cu-Mg-Ag alloy

Effects of Cu Content and Heat Treatment Process on Microstructures and Mechanical Properties of Al−Si−Mg−Mn−xCu Cast Aluminum Alloys

Effects of Cu content on the microstructure, mechanical property, and hot tearing susceptibility of die casting hypereutectic Al–22Si–0.4Mg alloy