Abstract:In this research paper, the effects of copper addition (0.02 wt.%–7.2 wt.%) on microstructure, mechanical, corrosion, and thermal properties of 5754 aluminum alloy are studied by optical microscope, Brinell hardness testing machine and UTM machine, mass loss test and dilatometer, respectively. Microstructural characterization has shown that increasing copper weight percentage increases grain refinement of the aluminum alloy. The grain size is observed to decrease from 41.7 μm in the case of the 5754 alloys containing 0.02 wt.% Cu to 29.1 μm by the addition of 7.2 wt.% of Cu. XRD studies have revealed that the addition of copper into 5754 aluminum alloy forms precipitates of Al 2 CuMg. The grain refinement and the formation of precipitates increase the Brinell hardness from 41.4 HB in the case of 5754 alloys containing 0.02 wt.% of Cu to 96.8 HB in the case of the alloy containing 7.2 wt.% Cu. However, the intergranular corrosion resistance is observed to decrease with the increase in copper weight percentage. The coefficient of thermal expansion value (between 50 °C to 450 °C) is observed to decrease from 26.9 x 10 -6 (°C) −1 in the case of the 5754 alloys containing 0.02 wt.% of Cu to 25.3 x 10 −6 (°C) −1 in the case of the alloy containing 7.2 wt.% of Cu. The formation of more precipitate phases with the increase in Cu content in the alloy reduces the thermal expansion of the aluminum alloy because of the formation of precipitate phases. The Peak compressive stress value decreases from 1102 MPa (for 5754 alloys) to 502 MPa (sample e) due to forming precipitate phases and reducing solid solutions atoms.

Effect of Cu content on the mechanical properties of an Al–Cu–Mg–Ag alloy

The Effect of A Small Amount of Tungsten on the Microstructure of Mechanically Alloyed Ag37cu63

The Effect of Al on Microstructure and Properties of Cu-15Ni-8Sn During the Aging

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Effect of Cu addition on precipitation and age-hardening response of an Al-15%Mg2Si alloy

Microstructure evolution and properties of Cu–Ag microcomposites with different Ag content

Effect of Mn/Ag Ratio on Microstructure and Mechanical Properties of Heat-Resistant Al-Cu Alloys

Strengthening Effect of Ag Precipitates in Cu–Ag Alloys: A Quantitative Approach

Microstructure, Mechanical Properties, and Corrosion Behavior of Al-4.0Cu-1.1Li-0.5Mg-xAg Alloys

Influence of Cu content on the hardenability of Al-xCu-1.1Li alloys

The microstructures and mechanical properties of a highly alloyed Al-Zn-Mg-Cu alloy: The role of Cu concentration

Effect of Mg content on Cu precipitation behavior in Al-Cu-Mg ternary alloy by molecular dynamics simulation

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Influence of Mg Contents on Aging Precipitation Behavior of Al–3.5Cu–xMg Alloy

Effect of Addition of Cu on Microstructure and Some Properties of 5754 Aluminum Alloy

Effect of Cu Content on Microstructure and Mechanical Properties for High-Strength Deposited Metals Strengthened by Nano-Precipitation

Effects of Mg content on microstructure and mechanical properties of low Zn-containing Al−xMg−3Zn−1Cu cast alloys

Influence of Mg content on ageing precipitation behavior of Al-Cu-Li-x alloys

Effect of Low Cu Content and Heat Treatment on the Microstructure and Mechanical Properties of High-Vacuum Die-Cast AlSiMgMn Alloys

Effect of Cu Content on the Precipitation Behaviors, Mechanical and Corrosion Properties of As-Cast Ti-Cu Alloys

Effect of Al Addition and Heat Treatment on the Microstructures and Corrosion Resistance of Mg-Cu Alloys