Abstract:Light olefins, as the backbone of the chemical and petrochemical industries, are produced mainly via steam cracking route. Prediction the of effects of operating variables on the product yield distribution through the mechanistic approaches is complex and requires long time. While increasing in the industrial automation and the availability of the high throughput data, the machine learning approaches have gained much attention due to the simplicity and less required computational efforts. In this study, the potential capability of four powerful machine learning models, i.e., Multilayer perceptron (MLP) neural network, adaptive boosting-support vector regression (AdaBoost-SVR), recurrent neural network (RNN), and deep belief network (DBN) was investigated to predict the product distribution of an olefin plant in industrial scale. In this regard, an extensive data set including 1184 actual data points were gathered during four successive years under various practical conditions. 24 varying independent parameters, including flow rates of different feedstock, numbers of active furnaces, and coil outlet temperatures, were chosen as the input variables of the models and the outputs were the flow rates of the main products, i.e., pyrolysis gasoline, ethylene, and propylene. The accuracy of the models was assessed by different statistical techniques. Based on the obtained results, the RNN model accurately predicted the main product flow rates with average absolute percent relative error (AAPRE) and determination coefficient (R2) values of 1.94% and 0.97, 1.29% and 0.99, 0.70% and 0.99 for pyrolysis gasoline, propylene, and ethylene, respectively. The influence of the various parameters on the products flow rate (estimated by the RNN model) was studied by the relevancy factor calculation. Accordingly, the number of furnaces in service and the flow rates of some feedstock had more positive impacts on the outputs. In addition, the effects of different operating conditions on the propylene/ethylene (P/E) ratio as a cracking severity factor were also discussed. This research proved that intelligent approaches, despite being simple and straightforward, can predict complex unit performance. Thus, they can be efficiently utilized to control and optimize different industrial-scale units.

Modeling and application of SL-Ⅱ ethylene pyrolysis furnace

Physical Properties Computation of Pure Components for Ethylene Slurry Polymerization System

Modeling of an Industrial Polycondensation Process for Polyethylene Terephthalate

System design and realization of on-line prediction of ethylene pyrolyzer based on mechanism model

Quality Predicting Models for Ethylene Terpolymerization to High-Performance Polyethylene

On-line Measurements and Model Analysis of Gas-phase Ethylene Polymerization Process in Fluidized Bed Reactor (II)

A Multi-Scale Model of Naphtha Pyrolysis Process

Modeling and Optimization of Ethane Steam Cracking Process in An Industrial Tubular Reactor with Improved Reaction Scheme

Simultaneous Simulation of Ethylene Slurry Polymerization Process

Method of Predicting Equimolecular Mixture of Ethylene Cracking Feedstock

Modeling of the Molecular Weight Distribution and Short Chain Branching Distribution of Linear Low-Density Polyethylene from a Pilot Scale Gas Phase Polymerization Process

Analysis of thermodynamic equilibrium yield and process simulation for catalytic pyrolysis of light hydrocarbons based on one set of independent reactions

A method to predict naphtha detailed composition based on normal physical characteristics

Estimation of the flow rate of pyrolysis gasoline, ethylene, and propylene in an industrial olefin plant using machine learning approaches

Experimental Investigation and Modeling of Steam Cracking of Fischer–Tropsch Naphtha for Light Olefins

Simulating Polyethylene Pyrolysis from a Generalized Molecular-Level Kinetic Model

Prediction of Ethylene and Propylene Release During Coal Pyrolysis with Modified CPD Model

Coke yield prediction model for pyrolysis and oxidation processes of low-asphaltene heavy oil

Three-scale Integrated Optimization Model of Furnace Simulation, Cyclic Scheduling, and Supply Chain of Ethylene Plants

Recirculation and reaction hybrid intelligent modeling and simulation for industrial ethylene cracking furnace

Empirical modeling of normal/cyclo-alkanes pyrolysis to produce light olefins