Abstract:AbstractThe Laue microdiffraction technique was used to investigate the strain field caused by the shot-peening operation and its redistribution after thermal hold or fatigue in a model nickel-based superalloy with an average grain size of 40μm$$40\,{\upmu }\hbox {m}$$. Micrometer and millimeter size mappings showed that the plastic deformation introduced by shot-peening in the whole sample partially relaxes after a thermal exposure at 450∘C$$450^{\circ }\hbox {C}$$ and was fully redistributed by the fatigue of the material, except in the hardened layer close to the sample edge. Diffraction patterns permitted to measure separately the strains related to the average alloy (γ+γ′$$\gamma +\gamma ^{\prime }$$) and to the γ′$$\gamma ^{\prime }$$ phase. No difference was observed between the two deviatoric strain fields. Even if there were small stresses in the inner part of the samples, the sensitivity of the Laue microdiffraction method was large enough to quantitatively characterize the crystal misorientations and the deviatoric strain redistributions. Useful data were provided not only at the grain scale but also at the mesoscopic scale, thus bridging the gap between the sin2ψ$$\hbox {sin}^{2}\psi $$ and Ortner’s methods used to determine residual stresses, respectively, in fine and single-grain microstructures. The obtained results are also of first interest for a quantitative comparison with HR-EBSD measurements in the scanning electron microscope. Energy coupled measurements with an energy-dispersive point detector were also performed to determine the full elastic strain tensors associated with the γ$$\gamma $$ and γ′$$\gamma ^{\prime }$$ phases. We demonstrated that, for Ni-based superalloys, the accuracy on strains and stresses was, respectively, of the order of 1×10-3$$1\times 10^{-3}$$ and 250 MPa for the diagonal components of tensors. The measurements suffered from the 150 eV resolution of the detector which made it difficult to the separate the energies of the γ$$\gamma $$ and γ′$$\gamma ^{\prime }$$ phases. Owing to large crystal misorientations, the microdiffraction technique was not able to determine elastic strains and hardening in the highly deformed layer, where a large amount of plastic strain and a number of defects were accumulated. Some improvements are proposed to overcome these difficulties.

XRD Measurement of Residual Stress of Nickel-Based Monocrystalline Superalloy AM1

Investigation of fatigue mesoscopic mechanical properties of a nickel-based superalloy by instrumented microindentation measurements

X-ray Diffraction Analysis for Residual Stress in Shot Peened Layer of DD3 Nickel-Based Single Crystal High Temperature Alloy

A Study of Fatigue Mesoscopic Elasto-Plastic Properties of a Nickel-Base Superalloy by Instrumented Microindentation Measurements

Quantitative Study of High-Frequency Fatigue Hole-Edge Stresses in Nickel-Based Single-Crystal Superalloy

Characterization of Distribution of Microstructure and Micro-mechanical Properties of Nickel-Based Single Crystal Superalloy Within the Shot-Peened Layer

Influence of Shot Peening on Surface-Layer Characteristics of a Monocrystalline Nickel-Based Superalloy

Local strain redistribution in a coarse-grained nickel-based superalloy subjected to shot-peening, fatigue or thermal exposure investigated using synchrotron X-ray Laue microdiffraction

Characterization of distribution of residual stress in shot-peened layer of nickel-based single crystal superalloy DD6 by nanoindentation technique

Effect of Shot Peening on Surface Characteristics of Ni-Based Single-Crystal Superalloy

Mapping of three-dimensional residual stresses by neutron diffraction in nickel-based superalloy discs prepared under different quenching conditions

Surface Mechanical Property and Residual Stress of Peened Nickel-Aluminum Bronze Determined by In-Situ X-Ray Diffraction

X-ray Residual Stress Analysis of Nitrided Low Alloyed Steels

Research on Finite Element Simulation and Recrystallization of Laser Shock Peened Nickel-Based Single-Crystal Superalloy

Grinding surface and subsurface stress load of nickel-based single crystal superalloy DD5

Experimental validation of residual stress thermomechanical simulation in as-quenched superalloy discs by using diffraction and incremental hole-drilling methods

Nondestructive Evaluation of Residual Stress in Shot Peened Inconel Using Ultrasonic Minimum Reflection Measurement

Measurement of two-dimensional residual stress in nanocrystalline superelastic NiTi fabricated with pre-strain laser shock peening

Residual Stress and Precipitation Evolution of Bulk Nickel-Based Superalloy During Heat Treatment

The Generation, Measurement, Prediction, and Prevention of Residual Stress in Nickel-Based Superalloys: A Review

Turning/Shot peening of Nickel-based powder metallurgy superalloy: Effect on surface integrity and high-temperature low-cycle fatigue properties