Abstract:The significant characteristics of the nickel-based Inconel 718 (IN718) superalloy are high strength, fatigue capacity, rupture strength, corrosion resistance, and creep resistance at temperatures exceeding 650 °C, which opens the application of IN718 for aircraft parts. The mechanical properties and surface residual stress (SRS) of the IN718 superalloy have been affected by fabrication and post-processing procedures, which shorten the service life of components. For the fabrication of complex aviation components, additive manufacturing of aerospace materials like IN718 has opened up new production techniques. However, localized melting and solidification produce anisotropy microstructure and a crystallographic texture with substantial tensile residual stress. These are responsible for mechanical anisotropy and pose metrological challenges for diffraction-based SRS detection. Knowing the magnitude and nature of SRS is crucial since they affect a mechanical properties and life of the parts. In this study, IN718 alloys were fabricated using the laser-based powder bed fusion (L-PBF) technique, and the impact of the standard ageing heat treatment (SAHT) process was assessed. The as-fabricated (AF) IN718 microstructure was found to have columnar dendritic structure and Laves phases in the interdendritic regions along the build direction. The SAHT sample microstructure led to the homogeneous precipitation of γ ′ and γ ′′ strengthening phases with δ and brittle Laves phases in grain boundaries. The average grain size of 41.56 μm in AF samples was increased to 44.80 μm after SAHT. The reduction of dislocation movements resulted in converting low angle grain boundaries found in the AF sample to high angle grain boundaries. SAHT samples displayed cubical texture along the and directions in the (001) plane. Following SAHT, there were increases in yield and ultimate tensile strength of 26.44% and 44.74%, respectively. On the other hand, the degree of elongation decreased to 36.19%. TRS in AF samples was converted into compressive surface residual stress following SAHT due to the phase transition. The process–structure–property relationship and the impacts of SAHT on the mechanical characteristics of the IN718 produced by L-PBF have been improved upon through this study.

On the Residual Stress Relaxation in Inconel 718 Superalloys at High Temperature by Real-Time Neutron Diffraction

Estimation of Residual Stresses by Nanoindentation in an Experimental High Strength Microalloyed Steel Subjected to Rapid Thermal Cycles

Mapping of three-dimensional residual stresses by neutron diffraction in nickel-based superalloy discs prepared under different quenching conditions

Study of pre-precipitated 8 phase promoting deformation twinning and recrystallization behavior of Inconel 718 superalloy during hot compression

The Effect of Low Temperature Range Heat Treatment on the Residual Stress of Cold Gas Dynamic Sprayed Inconel 718 Coatings via Neutron Diffraction

In-situ SEM study of temperature-dependent tensile behavior of Inconel 718 superalloy

Deformation mechanisms of Inconel-718 at nanoscale by molecular dynamics

Investigations on microstructure, crystallographic texture evolution, residual stress and mechanical properties of additive manufactured nickel-based superalloy for aerospace applications: role of industrial ageing heat treatment

Dynamic recrystallisation in Inconel®718 at creep conditions

Evolution of residual stress and its impact on Ni-based superalloy

Residual stress release and corresponding microstructural changes in high-energy impact-modified GH4169 after aging at 425 °C and 650 °C

Exploring the role of Type-II residual stresses in a laser powder bed fusion nickel-based superalloy using measurement and modeling

Experimental validation of residual stress thermomechanical simulation in as-quenched superalloy discs by using diffraction and incremental hole-drilling methods

Effect of heat treatment on the microstructural evolution of a nickel-based superalloy additive-manufactured by laser powder bed fusion

New insights into the stress rupture life enhancement mechanisms of a nickel-based superalloy

Measuring the effect of residual stress on the machined subsurface of Inconel 718 by nanoindentation

In Situ Heating Neutron and X‐Ray Diffraction Analyses for Revealing Structural Evolution during Postprinting Treatments of Additive‐Manufactured 316L Stainless Steel

The Dependence of Stress and Strain Rate on the Deformation Behavior of a Ni‐based Single Crystal Superalloy at 1050°C

Research on microplastic deformation of Inconel718 under the conditions of high temperature and high strain rate

Effect of stress-relief heat treatment on the stress-rupture properties of a nickel-based superalloy manufactured by laser powder bed fusion

Influence of Residual Stress on the High-Temperature Tribological Performance of Nickel-Based Superalloy