Abstract:As one of the most important surface strengthening method, shot peening is widely used to improve the fatigue and stress corrosion crack resistance of components by introducing the refined microstructure and compressive residual stress in the surface layer. However, the mechanical properties of this thin layer are different from the base metal and are difficult to be characterized by conventional techniques. In this work, a micro uniaxial tensile tester equipped with in-situ X-ray stress analyzer was employed to make it achievable on a nickel-aluminum bronze with shot peening treatment. According to the equivalent stress-strain relationship based on Von Mises stress criterion, the Young's modulus and yield strength of the peened layer were calculated. The results showed that the Young's modulus was the same as the bulk material, and the yield strength corresponding to the permanent plastic strain of 0.2% was increased by 21% after SP. But the fractographic analysis showed that the fracture feature of the surface layer was likely to transform from the dimple to the cleavage, indicating the improved strength might be attained at the expense of ductility. The monotonic and cyclic loading were also performed via the same combined setup. In addition, the specific relaxation behavior of compressive residual stress was quantified by linear logarithm relationship between residual stress and cycle numbers. It was found that the compressive residual stress mainly relaxed in the first few cycles, and then reached steady state with further cycles. The relaxation rate and the stable value were chiefly depended on the stress amplitude and number of cycles. The retained residual stress kept in compressive under all given applied stress levels, suggesting that the shot peening could introduce a more stable surface layer of compressive residual stress other than the elevated strength of nickel-aluminum bronze alloy. (C) 2017 Elsevier B.V. All rights reserved.

On the Micro-Residual Stress Measurement of Shot Peened Nickel-Based Alloy Material by using Slot-Milling Method

Fabrication of speckle patterns by focused ion beam deposition and its application to micro-scale residual stress measurement

Determination of Residual Stress Distribution Combining Slot Milling Method and Finite Element Approach

Surface Mechanical Property and Residual Stress of Peened Nickel-Aluminum Bronze Determined by In-Situ X-Ray Diffraction

A Micro-Scale Strain Rosette for Residual Stress Measurement by SEM Moiré Method

Micro-slotting Residual Stress Measurement Technique for Understanding Fatigue Performance of Open-Hole Ti-6Al-4V Samples

Quantitative Study of High-Frequency Fatigue Hole-Edge Stresses in Nickel-Based Single-Crystal Superalloy

X-ray Diffraction Analysis for Residual Stress in Shot Peened Layer of DD3 Nickel-Based Single Crystal High Temperature Alloy

The evolution of residual stress and microstructure in shot peened s30432 austenitic stainless steel at high temperatures

Residual Stress Assessment of Interconnects by Slot Milling with Fib and Geometric Phase Analysis

Measurement of two-dimensional residual stress in nanocrystalline superelastic NiTi fabricated with pre-strain laser shock peening

Effect of stress shot peening on the residual stress field and microstructure of nanostructured Mg-8Gd-3Y alloy

Nanoscale microstructural factors contributing to the improvement of the micromechanical wear properties of mechanical shot-peened nickel-based superalloys

Effects of residual stress on the isothermal tensile behavior of nanocrystalline superelastic NiTi shape memory alloy

Measurement of the Residual Stress in the Micro Milled Thin Walled Structures

Effect of Shot Peening on Surface Damage Evolution Behavior of Cu-19Ni Alloy

Residual Stress Measurement on a MEMS Structure With High-Spatial Resolution

Quantitative evaluation of residual stress and microstructural effects on the surface hardness of machined Ti-6Al-4 V alloy with microscopic characterization techniques

Measurement of residual stress in micro-end-milling of AMS 5833 Co-Cr-Ni alloy thin film

Experimental Study on Macro- and Microstress State, Microstructural Evolution of Austenitic and Ferritic Steel Processed by Shot Peening

Turning/Shot peening of Nickel-based powder metallurgy superalloy: Effect on surface integrity and high-temperature low-cycle fatigue properties