Abstract:The effect of coating cracking during depth-sensing indentation testing (e.g. nanoindentation testing) on systems comprising thin hard coatings (e.g. TiN) on a less stiff, hard substrate (e.g. steel) has been investigated in order to establish whether, at such small scales, the occurrence of annular through-thickness cracks around indentation sites can be detected from load–displacement plots and whether any accompanying localized debonding of the coating from the substrate can also be identified. Experiments were performed on thin TiN and NbN monolayers, and compositionally modulated TiN/NbN and TiN/ZrN deposited onto hard steel or stainless steel substrates. Above a critical load (Pcrit) in the range 80–500mN, all systems exhibited annular through-thickness cracks around indentation sites. The cracking was found to be accompanied by a discrete change in gradient of the loading portion of the load–displacement curve. Also, analysis of the unloading curves beyond this point showed that elastic recovery was controlled by the elastic modulus of the underlying substrate material alone. The cracking mechanism has been characterized using scanning electron microscopy, coupled with optical profilometry to map the detailed z-displacement of the surface — a procedure critical to understanding whether coating–substrate debonding had occurred. Some cracks were found to show a spiral morphology and the effect of indentation loading rate was investigated to see if appearance of these cracks was loading-rate sensitive. Our results highlight the problems inherent in assessing both the interfacial failure and the interfacial fracture toughness of thin film coated systems at the small contact scales (⩽1μm) associated with crack genesis where it is difficult to confirm the extent of sub-surface cracks by conventional means. We have also demonstrated that both load–displacement and load–displacement squared plots are necessary if a more complete understanding of system behaviour is to be gained. Also, a simple fracture mechanics model for the annular cracking behaviour seen in such systems has been derived and used to estimate a value of Gic (the interfacial work of fracture) as 180Jm−2 for the TiN/ZrN-stainless steel system.

Evaluation of Bonding Strength of Thin Hard Films by Spherical Rolling Test

A Friction Evaluation Method Based on Barrel Compression Test

Study on interface behavior of Be/CuCrZr alloy by diffusion bonding

A novel cylindrical punch method to characterize interfacial adhesion and residual stress of a thin polymer film

Residual Stresses And Debonding Of Diamond Films On Titanium Alloy Substrates

Self-Debonding of Adhesive Thin Films on Convex Cylindrical Surfaces and Spherical Surfaces

Thin hard coatings fracture propagation during the impact test

The Tribological Behaviors of Three Films Coated on Biomedical Titanium Alloy by Chemical Vapor Deposition

Effects of thin hard film deposition on fatigue strength of AA7075-T6

Determination of yielding and debonding in Al–Cu thin films from residual stress measurements via diffraction

Subsurface propagation of partial ring cracks under rolling contact: Part I. Experimental studies

Substrate and bonding layer effects on performance of DLC and TiN biomedical coatings in Hank's solution under cyclic impact–sliding loads

Study on fatigue and wear behaviors of a TiN coating using an inclined impact-sliding test

The effect of coating cracking on the indentation response of thin hard-coated systems

The Relationship Between Friction and Film Thickness in EHD Point Contacts in the Presence of Longitudinal Roughness

Interfacial debonding in a thin plate bonded to a rigid substrate with a circular hole

Contact size effects on the friction and wear of amorphous carbon films

Study of the Plastic Behavior of Rough Bearing Surfaces Using a Half-Space Contact Model and the Fatigue Life Estimation According to the Fatemi–Socie Model

A METHOD FOR BIAXIAL F CTU ST' SS TEST OF NANOSCALE FILM

Micro-Scale Delaminating and Buckling of Thin Film on Soft Substrate

Buckle-driven Delamination of Thin Film and the Influence of the Casimir or Van Der Waals Force Interaction