Abstract:Using granulated blast furnace slag (GGBS) as the volcanic ash material and fly ash (FA) as the supplementary material, the study was conducted to investigate the mix proportions of an alkali-activated solid waste cementitious material under the stimulating effect of alkali activator carbide slag (CS). This type of cementitious material could serve as a substitute for a portion of cement usage, contributing to resource conservation and mitigating environmental pollution caused by solid waste. This facilitates green and sustainable development. Firstly, an analysis of three raw materials was conducted, and the mix proportions were designed with reference to the CaO-Al 2 O 3 -SiO 2 system of Portland cement. Then 28 groups of specimens were prepared based on the designed mix proportions. The flowability and setting time of each group of specimens were tested. It was observed that an increase in the amount of CS and a decrease in the amount of GGBS resulted in decreased flowability and earlier setting times of the specimens. Additionally, FA exhibited a retarding effect on setting time. Compressive strength tests were conducted on these specimens, revealing that the optimal CS content ranged between 20 % and 40 %. Overall, FA had minimal impact on compressive strength, but it contributed to increased compressive strength in the specimens at later ages. Subsequently, microscopic characterization of the hydration products was performed using X-ray Diffraction (XRD), Fourier Transform Infrared (FTIR), Differential Thermal Analysis (DTA), Scanning Electron Microscope (SEM), and Energy Dispersive Spectrometer (EDS). The hydration products were identified as predominantly composed of calcium silicate hydrate. The quality and defects in the microstructure of gel products from various specimen formulations were compared to elucidate differences in macroscopic performance. Finally, the hydration process mechanism diagram of alkali-activated materials was presented to illustrate the stimulation and formation of gel products, primarily composed of C-S-H. This diagram revealed the principles behind the action of alkali-activated cementitious materials. The proposed design and testing methodology for the GGBS-FA-CS system in this study had certain reference significance for research in the direction of alkali-activated solid waste cementitious materials.

Study on High-Strength Composite Portland Cement with a Larger Amount of Industrial Wastes

Study on Mixing Cement-Waste By-Product to Stabilize Soft Marine Clay

Study on the Alkali–Sulfur Co-Activation and Mechanical Properties of Low-Carbon Cementitious Composite Materials Based on Electrolytic Manganese Residue, Carbide Slag, and Granulated Blast-Furnace Slag

Insight into the performance of composite binder with high-volume steel slag, blast furnace slag and desulfurization gypsum

Mechanical properties and chemical microscopic characteristics of all-solid-waste composite cementitious materials prepared from phosphogypsum and granulated blast furnace slag

Experimental Study Based on Box–Behnken Design and Response Surface Methodology for Optimization Proportioning of Activated Lithium Slag Composite Cement-Based Cementitious Materials

Resource utilization of solid waste from steel industries in cement-based cementitious materials: Mechanical properties, hydration behaviors, and environmental impact

The Ratio Optimization and Strength Mechanism of Composite Cementitious Material with Low-Quality Fly Ash

Evaluation of compressive strength and chloride permeability of cement-based materials with high-volume compound mineral admixtures

Enhancement of ultra-fine slag on compressive strength of solid waste-based cementitious materials: Towards low carbon emissions

Preparation and Hydration Mechanisms of Low Carbon Ferrochrome Slag-Granulated Blast Furnace Slag Composite Cementitious Materials

Preparation of steel slag-based cementitious materials compounded with GBFS and phosphogypsum: mix design, hydration, and microstructure characteristic

Effect of Steel Slag and Granulated Blast-furnace Slag on the Mechanical Strength and Pore Structure of Cement Composites

Compressive Strength and Microstructural Development of Cementitious Mixtures Incorporating Ultrafine Granulated Blast Furnace Slag

Preparation and Hydration Properties of Steel Slag-Based Composite Cementitious Materials with High Strength

Sustainable clinker-free solid waste binder produced from wet-ground granulated blast-furnace slag, phosphogypsum and carbide slag

Design and Preparation Technology of Green Multiple Solid Waste Cementitious Materials

The Impact of Fly Ash on the Properties of Cementitious Materials Based on Slag-Steel Slag-Gypsum Solid Waste

Study on the preparation, performance, and mechanism for solid waste cementitious materials

Enhancement of compressive strength of high-volume fly ash cement paste by wet grinded cement: Towards low carbon cementitious materials

Influence of solid waste gypsum and additives on the properties of sulfoaluminate cement-fly ash-gangue ternary binder