Abstract:Silicon based power micro-electro-mechanical system (MEMS) applications require highspeed microrotating machinery operating stably over a large range of operating conditions. The technical barriers to achieving stable high-speed operation with micro-gas-bearings are governed by (1) stringent fabrication tolerance requirements and manufacturing repeatability, (2) structural integrity of the silicon rotors, (3) rotordynamic coupling effects due to leakage flows, (4) bearing losses and power requirements, and (5) transcritical operation and whirl instability issues. To enable high-power density the micro-turbomachinery must be run at tip speeds comparable to conventional scale turbomachinery. The rotors of the micro-gas turbines are supported by hydrostatic gas journal and hydrostatic gas thrust bearings. Dictated by fabrication constraints the location of the gas journal bearings is at the outer periphery of the rotor. The high bearing surface speeds (target nearly 10 x 10(6) mm rpm), the very low bearing aspect ratios (L/D < 0.1), and the laminar flow regime in the bearing gap (Re < 500) place these micro-bearing designs into unexplored regimes in the parameter space. A gas-bearing supported micro-air turbine was developed with the objectives of demonstrating repeatable, stable high-speed gas-bearing operation and verifying the previously developed micro-gas-bearing analytical models. The paper synthesizes and integrates the established micro-gas-bearing theories and insight gained from extensive experimental work. The characteristics of the new micro-air turbine include a four-chamber journal bearing feed system to introduce stiffness anisotropy, labyrinth seals to avoid rotordynamic coupling effects of leakage flows, a reinforced thrust bearing structural design, a redesigned turbine rotor to increase power, a symmetric feed system to avoid flow and force nonuniformity, and a new rotor micro-fabrication methodology for reduced rotor imbalance. A large number of test devices were successfully manufactured demonstrating repeatable bearing geometry. More specifically, three sets of devices with different journal bearing clearances were produced to investigate the dynamic behavior as a function of bearing geometry. Experiments were conducted to characterize the "as-fabricated" bearing geometry, the damping ratio, and the natural frequencies. Repeatable high-speed bearing operation was demonstrated using isotropic and anisotropic bearing settings reaching whirl-ratios between 20 and 40. A rotor speed of 1.7 x 10(6) rpm (equivalent to 370 m/s blade tip speed or a bearing DN number of 7 x 10(6) mm rpm) was achieved demonstrating the feasibility of MEMS-based micro-scale rotating machinery and validating key aspects of the micro-gas-bearing theory. [DOI: 10.1115/1.3123343]

Development of Gas Lubricated MEMS Turbine

High-Speed Operation of a Gas-Bearing Supported MEMS-Air Turbine

Dynamic Lubrication of Micro Gas Bearings at an Ultra High Speed

A novel integrated micro-scale closed synthetic-jet-like flow field as gas lubrication in MEMS devices

Packaging and Testing of High Speed Rotor for MEMS Gas Turbine Engines

Demonstration of a Microfabricated High-Speed Turbine Supported on Gas Bearings

Development of a Gas Turbine with a 20 Mm Rotor: Review and Perspectives

High-speed microfabricated silicon turbomachinery and fluid film bearings

Modeling and Analysis of Micro Hybrid Gas Spiral-Grooved Thrust Bearing for Microengine

Micro-rotor Dynamics for Micro-Electro-mechanical Systems (MEMS)

The Experimental Study of a Miniature High-Speed Gas-Bearing Expansion Turbine

Design and Fabrication of the Micro Turbine for Micro Gas Turbine Engine

Fabrication and Testing of a High-Speed Microscale Turbocharger

Developments of the Miniature Gas Bearing High Speed Turbo Machinery

Progress of Bearings in Micro Rotating Machinery

Power Mems and Microengines

A Performance Test Rig and Its Measuring System for Centripetal Turbines of Micro-Gas-Turbines

The Design and Simulation of Micro Gas Journal Bearing for Micro Gas Turbine Engine

On the Performance of Gas-Lubricated Bearing-Rotor System in Microengine

Development of miniature heat pump based on MEMS technology

Research development of measuring methods on the tribology characters for movable MEMS devices: a review