Abstract:Urea–formaldehyde (UF) and phenol–formaldehyde (PF) resins are the most widely used adhesives in the production of wood composites, and are cured through hot-pressing to provide adhesion strength with the composites. This study investigates the relationship between thermal curing behavior monitored by differential scanning calorimetry (DSC) and adhesive bond strength development measured by an automated bonding evaluation system (ABES) for UF and PF resins with different molecular weights ( M w ). DSC results demonstrated that UF resins cured faster than PF resins, as indicated by a lower apparent activation energy ( E a ). In addition, UF and PF resins with lower M w cured faster in the early stages of curing and slower in the latter stages of curing as compared to higher- M w resins. Furthermore, according to the ABES results, when increasing the molecular weight, both UF and PF resins exhibited greater adhesive bond strength, irrespective of pressing parameters (temperature and time). The isothermal DSC and ABES results demonstrated that the adhesive bond strength increased with an increase in the degree of cure of the resins, indicating a correlation between them. It also showed that UF resins attained optimal adhesive bond strength at low temperature (110–130 °C) in roughly 180 s while PF resins attained it at high temperature (120–130 °C) in about 300 s. However, the degree of cure under isothermal scans was inconsistent with temperatures. These results indicate that the degree of cure is closely related to the adhesion strength development of UF and PF resins which are curing at low and high temperatures to obtain the optimum adhesion strength.

Study on the Curing Reaction Between Isocyanate Adhesive and High- Moisture Content Wood by DSC

Studies on Cure Kinetics of Diglycidyl Ether of 4,4′-Bisphenol/4,4′-diaminobiphenyl Using the Advanced Isoconversional Method

Cure Kinetics of an Epoxy Resin Containing Naphthyl/dicyclopentadiene Moieties and Bis‐phenoxy (3‐hydroxy) Phosphine Oxide System and Properties of Its Cured Polymer

Comparison between cure kinetics by means of dynamic rheology and DSC of formaldehyde-based wood adhesives

Study of Post-curing Properties of Wood Flour Reinforced Phenolic Molding Materials

DSC Study on the Effect of Cure Reagents on the Lignin Base Epoxy Cure Reaction

Modeling of curing and post-curing kinetics for a thermoset adhesive

Cure reaction of epoxy resin used for composite aircraft structures

Study on the Cure Kinetics of Middle Temperature Curing 3234 Epoxy Resin System

Research on Curing Reaction Kinetics of Epoxy Resin/Hollow GlassMicrospheres System by Non-isothermal DSC Method

Relationship between thermal curing behavior and bond strength development in formaldehyde-based resins with different molecular weights

Long-term outcome after arthroscopic repair of type II SLAP lesions: results according to age and workers' compensation status.

Study in Curing Properties of Two-Component Solvent-Free Polyurethane Adhesive

Preparation and properties of isocyanate prepolymer/corn starch adhesive

Study on curing kinetics of TDE-85 epoxy resin by means of DSC and DMA

Curing Kinetics of DGEBA/Polyether Amine by Isothermal DSC

Curing Kinetics of Methylene Diphenyl Diisocyanate—Based Polyurethane Elastomers

DSC Analysis of the Effect of Moisture on the Reactions of PMDI with the Starch and Modified Starch

Reliability evaluation of a new method developed for DSC curing kinetic model of epoxy resin

Isothermal kinetics and thermodynamics studies of curing reaction of epoxy-aromatic diamine reinforced with epoxy functional MWCNT

Thermal curing behavior of phenol formaldehyde resin-impregnated paper evaluated using DSC and dielectric analysis