Abstract:The SO2/NOX pollution in the flue gas of non-ferrous smelting is increasingly serious. At the same time, the accumulation of red mud (RM) in the aluminum industry and phosphorus sludge (PS) in the yellow phosphorus industry has caused serious harm to the environment. To remove SO2 and NOX from the non-ferrous smelting flue gas and realize the resource utilization of the above two solid wastes, an ultrasonic field was used in this study to strengthen the PS excited O3 process and RM wet desulfurization and denitrification process. In the process of O3 excitation, the response surface method (RSM) is used to obtain the optimal O3 excitation concentration, and the optimal reaction conditions are designed based on the response surface optimization model: T is 53.226 °C, power density is 0.4 W/cm2, PS concentration is 51.433 g/L, O3 formation concentration up to 250 ppm or more, which provides a theoretical basis for subsequent desulfurization and denitrification steps. It is proved that this study can replace the expensive traditional O3 generator and provide a basis for NOX removal in the following process. In addition, the optimum experimental conditions of ultrasonic enhanced RM desulfurization and denitrification process were also explored. Under ultrasonic frequency of 28 kHz, ultrasonic power density of 0.4 W/cm2, T of 50 °C, RM concentration of 15 g/L, and stirring intensity of 1000 rpm, the desulfurization efficiency of the reaction system can be maintained above 95 % within 250 min, and the denitrification efficiency can be maintained above 90 % within 250 min. The effect of desulfurization and denitrification in this study is much better than that of traditional methods. Finally, the reaction mechanism of ultrasonic enhanced O3 excitation and RM wet desulfurization and nitrogen removal was discussed by combining adsorption thermodynamics, isotherm, and kinetics. The results showed that the OH· free radicals generated by ultrasonic cavitation and the physical effects brought by emulsification had significant promoting effects.

Preparation of Desulfurizer from Ferrous Salt and Its Optimization

Experimental study of new desulfurizer for removal of H2S

Study and optimization of catalytic oxidation technology in spent caustic desulfurization

The Recycling of Ferric Salt in Steel Pickling Liquors: Preparation of Nano-sized Iron Oxide

Ultrasonic-enhanced Phosphorus Sludge Excited O3 Coupled Red Mud Simultaneous Desulfurization and Denitrification

Properties of MgAlCuFe Complex Oxides for FCC Desulfurization: Effect of Metal Salt Precursors

Experimental Study on the Preparation of Desulfurizer for Low Temperature Dry Desulfurization by Digesting CaO in Urea Solution

Studies on the Combined Technology of Chemical Precipitation and Electrocatalytic Oxidation for the Pretreatment of Desulfurization Wastewater

Performance and Optimization of Integrated Biogas Bio-desulfurization Reactor

Preparation and performance of sludge-based desulfurizer by calcification

A Study of High Temperature Desulfurization and Regeneration Using Iron-Calcium Oxides in a Fixed-Bed Reactor

Low-temperature oxidation behavior and mechanism of semi-dry desulfurization ash from iron ore sintering flue gas

Study on preparation and properties of supported compound desulfurizer for Bayer dissolution

Preparation of calcium ferrite by flue gas desulfurization gypsum

Semidry Desulfurization Process with in Situ Supported Sorbent Preparation

Enhanced Desulfurization by Tannin Extract Absorption Assisted by Binuclear Sulfonated Phthalocyanine Cobalt Polymer: Performance and Mechanism

SO2 Removal by Nano-Sized ZnO and Attapulgite Compounds at Room Temperature

Application and removal mechanism of ZnO/bentonite desulfurizer in the dry desulfurization

Advances on resource utilization of semi-dry desulfurization ash by thermal decomposition: a high-efficiency and low-temperature method for large-scale processing

Study on dry desulfurization performance of MnOx hydrothermally loaded halloysite desulfurizer

Resource utilization of semi-dry flue gas desulfurization ash by thermal treatment on sintering machine