Abstract:Polylactic acid has stood out among bio-based polymers for its usage in the food packaging industry and biomedical fields. Through the melt mixing process, the toughened poly(lactic) acid (PLA) was prepared with polyolefin elastomer (POE), incorporated via various ratios of nanoclay and a fixed amount of nanosilver particles (AgNPs). The correlation between the compatibility and morphology, mechanical properties, and surface roughness of samples with nanoclay was studied. The calculated surface tension and melt rheology confirmed the interfacial interaction demonstrated by droplet size, impact strength, and elongation at break. Each blend sample exhibited matrix-dispersed droplets, and the size of POE droplets steadily dropped with increasing nanoclay content, corresponding to the enhanced thermodynamic affinity between PLA and POE. Scanning electron microscopy (SEM) acknowledged that the inclusion of nanoclay in the PLA/POE blend ameliorated the mechanical performance by preferable localization in the interface of used components. The optimum value of elongation at break was acquired at about 32.44%, where the incorporation of 1 wt.% nanoclay led, respectively, to 171.4% and 24% enhancement rather than the PLA/POE blend with the composition of 80/20 and the virgin PLA. Similarly, the impact strength reached 3.46 ± 0.18 kJ m−1 as the highest obtained amount, showing the proximity of 23% progress to the unfilled PLA/POE blend. Surface analysis indicated that adding nanoclay caused the augment of surface roughness from 23.78 ± 5.80 μm in the unfilled PLA/POE blend to 57.65 ± 18.2 μm in PLA/POE contained 3 wt.% nanoclay. Rheological measurements implied that organoclay resulted in the strengthening of melt viscosity as well as the rheological parameters such as storage modulus and loss modulus. Han plot further showed that the storage modulus is always higher than the loss modulus in all prepared PLA/POE nanocomposite samples, corresponding to the restriction of polymer chains mobility induced by the formation of strong molecular interaction between nanofillers and polymer chains.

Interfacial Interaction of Clay with Binary Blends of Polyamide 6 with High-Density Polyethylene (HDPE) and HDPE-graft-acrylic Acid Studied by Positron Annihilation Lifetime Spectroscopy

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Blending Effects on Polymorphic Crystallization of Poly(l-lactide)

Rheology of Poly(lactic Acid)/poly(trimethylene Terephthalate) Blends Compatibilized by Clay or Maleic Anhydride-Grafted Poly(ethylene-Octene) Elastomer

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Effect of Nanoclay on the Morphological Properties of Ternary PA6/POE-g-MAH/LDPE Blend

Influence of Polarity on the Preferential Intercalation Behavior of Clay in Immiscible Polypropylene/Polystyrene Blend

Effect of Nanoclay on the Phase Separation Behavior of Poly（methyl Methacrylate）/poly（vinyl Acetate） Binary Polymer Blends

Joint Effect of Compatibilizer and Organo-Montmorillonite on Compatibilization of Polyamide-6/Poly(Phenylene Oxide) Blend: Morphology and Properties

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Microstructures and Mechanical Properties of Polypropylene/polyamide 6/Polyethelene-Octene Elastomer Blends

Reactive Compatibilization of Polyamide 6/Olefin Block Copolymer Blends: Phase Morphology, Rheological Behavior, Thermal Behavior, and Mechanical Properties

Flammability and phase-transition studies of nylon 6/montmorillonite nanocomposites

PREFERENTIAL INTERCALATION BEHAVIOR OF CLAY AND ITS EFFECT ON THE THERMAL DEGRADATION IN IMMISCIBLE PP/PS BLENDS

Effect of compounding sequence on the morphology of organoclay-filled PA6/PP/MAPP blends

MORPHOLOGICAL EVOLUTION AND VISCOELASTIC BEHAVIOR OF COMPATIBILIZED HDPE/PA6 BLENDS

Rheology, Morphology and Thermal Properties of a PLA/PHB/Clay Blend Nanocomposite: The Influence of Process Parameters

TOUGHENING OF ETHYLENE-PROPYLENE RANDOM COPOLYMER/CLAY NANOCOMPOSITES： COMPARISON OF DIFFERENT COMPATIBILIZERS

Investigation on polypropylene and polyamide-6 alloys/montmorillonite nanocomposites

Influence of organoclay filler and dicumyl peroxide (DCP) on the properties of the low-density polyethylene (LDPE)/thermoplastic starch (TPS) blend

Investigation of the Effect of Hybrid Nanofiller on the Mechanical Performance and Surface Properties of Bio-Based Polylactic Acid/Polyolefin Elastomer (PLA/POE) Blend