Abstract:To meet the practical application, a kind of commercially available Si3N4 powder by direct Si nitridation was used to fabricate dense Si3N4/SiC nanocomposite by pressureless sintering method. The price of this kind of powder is much lower than that of powder by imide decomposition. 5-30 vol% of SiC powder (average particle size: 80 nm) were added in the composite to investigate the effect of SiC particle. Totally 15 wt% of MgAl2O4 and ZrO2 (50 wt% each) were used as sihtering additives. With increasing SiC content, the densities of the composites decreased. α-β Si3N4 phase transformation was enhanced at low temperatures, but prohibited at high temperatures for large SiC content. The sample with larger SiC content gave a relatively smaller Si3N4 grain size because SiC particles limit the Si3N4 grain growth by pinning and prohibiting the grain boundary movement. An improvement of Young's modulus, flexural strength and hardness by the SiC addition was found. Further increase in SiC content resulted in a decrease of these properties because of the decreasing density for the samples sintered at low temperatures. With an intermediate sintering temperature, the samples with 20 vol% SiC reached to high flexural strength as 1050 MPa as a result of good density and relatively fine grain size structure. The decreased fracture toughness with increasing the SiC content was observed by the refinement of Si3N4 grain. However, it was improved with the increasing sintering temperature. The result of this study provided an economic way to fabricate the Si3N4/SiC nanocomposite with a strength higher than 1 GPa and appropriate fracture toughness.

Fabrication of YAG–SiC nanocomposites by spark plasma sintering

Sintering behaviour and mechanical properties of SiC/YAG composite powders by sol-gel methods

Fabrication of Si3n4/Sic Nanocomposites by Spark Plasma Sintering of Amorphous Sicn Powders Derived from A Polymeric Precursor

Microstructure and mechanical properties of SiC–mullite nanocomposite prepared by spark plasma sintering

SiC-Al_2O_3 Nanocomposites Superfast Densified by SPS

Effects of Adding Methods of YAG on Sintering Behaviour, Mechanical Properties and Microstructure of SiC Ceramic

Mechanical Properties and Microstructure of Sic-Zro2(3y)-Al2o3 Nanocomposites

Microstructure and properties of nano-laminated Y3Si2C2 ceramics fabricated via in situ reaction by spark plasma sintering

Fabrication and Mechanical Properties of Nano-SiC-Oxide Composites

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Fabrication, Microstructure, and Properties of SiC/Al 4 SiC 4 Multiphase Ceramics Via an In-Situ Formed Liquid Phase Sintering

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Preparation and Microstructure of Polycrystalline Al2O3–YAG Composites

Fabrication, microstructure, and properties of SiC/Al4SiC4 multiphase ceramics via an in-situ formed liquid phase sintering

Enhanced strength and toughness of SiC/C composite ceramics via SiC@graphene core–shell nanoparticles

ZrB2–SiC–G Composite Prepared by Spark Plasma Sintering of In‐Situ Synthesized ZrB2–SiC–C Composite Powders

Mechanical Properties and Microstructures of Al2O3–5 Vol.% YAG Composites

Fabrication, Microstructural Evolution, and Mechanical Properties of SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C Nanocomposites

In situ formation of Si3N4–SiC nanocomposites through polymer-derived SiAlCN ceramics and spark plasma sintering

Fabrication and mechanical evaluation of SiC–TiC nanocomposites by SPS

Synthesis and properties of porous SiN/SiC nanocomposites by carbothermal reaction between SiN and carbon