Abstract:Dispenser cathodes are the most widely used electron emission source in vacuum electron devices. The impregnant is the source for producing active substances in the dispenser cathodes, which play an irreplaceable role. However, impregnants’ phase structure and optical response properties have yet to be systematically investigated. Herein, four aluminates were prepared as impregnants via homogeneous-lyophilization followed by calcination. Due to the unique preparation process, the elemental distribution of aluminates is exceptionally uniform. Based on the first-principles DFT calculations, the primary phases of the two aluminates 532 and 411 were confirmed to be (Ba0.61Ca0.39)3Al2O6 (P2 1 3) and (Ba0.75Ca0.25)4Al2O7 (Cmca). At the same time, α-Ba2ScAlO5 and β-Ba2ScAlO5 are the only phases of aluminates 411-0.75Sc and 411-1.25Sc, respectively. XPS confirmed two chemical states of Ba and Sc in the aluminates. FT-IR and 27Al NMR indicate that the aluminum-oxygen skeleton in all aluminates exists mainly as [AlO4] tetrahedrons, accompanied by a small amount of distorted [AlOx] (x = 5, 6) polyhedrons. The UV–visible light absorption capacity, band gap and intra-structural electron transfer capacity of all aluminates are determined by UV–Vis DRS and PL spectra. The dispenser cathodes impregnated with aluminates 532 and 411 have zero-field current densities of 5.3 A/cm2 and 14.3 A/cm2 at 1100°Cb, respectively. The dispenser cathodes impregnated with aluminate containing scandium have different space-charge-limited current densities, i.e., 29.48 A/cm2 for 411-0.75Sc and 13.66 A/cm2 for 411-1.25Sc at 1000°Cb. This work will provide more options for synthesizing and applying impregnants.

ACCELERATED LIFE TEST STUDIES OF NEW COATED DISPENSER CATHODES

Degradation factors of a new long-life cathode

Life test studies on RV dispenser cathode life test studies on RV dispenser cathode

Degradation Factors Of A New Long Life Cathode

Aging Characteristic of Solar Coating and Their Cost-Effectiveness

The Study of Thin Film High–voltage Li-Ion Cathodes to Reveal Surface Reactions and Coating Performance

Understanding the surface structure evolution and electron emission behaviors during the activation of Ir-coated dispenser cathodes

A New Dispenser Cathode with Dual-Layer

Effect of Cathode Fabrication Method on Characteristics of Anode-Supported Tubular Solid Oxide Fuel Cells

Improvement of Low-Cycle Fatigue Life of Austenitic Stainless Steel by Multiple High-Density Pulsed Electric Currents

Carbon enhanced cementitious coatings: Alternative anode materials for impressed current cathodic protection systems intended for reinforced concrete

Application of Accelerating Rate Calorimeter in the Lithium-ion Battery Thermal Test

Isothermal and Cyclic Oxidation Performance of Vertically Cracked and Columnar Thermal Barrier Coating Structures Produced Using Axial Suspension Plasma Spraying Process

Surface Coating of NCM523 Cathode Electrodes by the Difunctional Block Copolymer/Lithium Salt Composites

Influence of AC-DC-AC Cycling with Hydrostatic Pressure on Accelerated Protective Performance Test of Glass Flake Epoxy Coating

Experimental Study On A New Lamo Cathode Of High Current Ion Source

Synthesis of impregnants for dispenser cathodes via homogeneous-lyophilization: Phase structure, optical response and emission property of four aluminates

Revealing the Accelerated Capacity Decay of a High-Voltage LiCoO<sub>2</sub> upon Harsh Charging Procedure

Graphite Slurry Heat Treatment Temperature for Improving the Durability of CNWs Anode Materials of Lithium-Ion Batteries

Cathode Performance as a Function of Inactive Material and Void Fractions

Pulse High Temperature Sintering to Prepare Single‐Crystal High Nickel Oxide Cathodes with Enhanced Electrochemical Performance (Adv. Energy Mater. 3/2023)