Abstract:InCl3@Li1.3Al0.3Ti1.7(PO4)3-F (InCl3@LATP-F) solid electrolyte powders are designed and fabricated by coating a uniform InCl3 layer on the surface of F--doped Li1.3Al0.3Ti1.7(PO4)3 (LATP-F) solid powders via a feasible wet-chemical technique. The assembled Li/InCl3@LATP-F/Li cell can undergo longer cycles of 2500 h at 0.4 mA cm-2 without obvious increases in the overvoltage compared to 1837 h for the Li/LATP-F/Li cell, and the interfacial resistance demonstrates a sharp decrease from 3428 to 436 Ω for the Li/InCl3@LATP-F/Li cell during the first 500 h. Importantly, the assembled LiCoO2/InCl3@LATP-F/Li cell delivers a high discharge specific capacity of 126.4 mAh g-1 with a 95.42% capacity retention ratio after 100 cycles at 0.5 C, and the value easily returns to 112.9 mAh g-1 when the current density is abruptly set back to 0.1 C after different rate cycles. These improved results can be mainly attributed to the fact that the InCl3 layer with a lithiophilic nature can react with lithium metal to form a Li-In alloy, which can guarantee homogeneous lithium ion flux to avoid the accumulation of ions/electrons across the interface and suppress the growth of lithium dendrites. Moreover, the InCl3 layer can prevent direct contact of the LATP-F solid electrolyte and lithium metal to effectively alleviate the reduction reaction of Ti4+ and preserve the structural stability of the composite electrolyte. Therefore, this work may provide an effective strategy to engineer and regulate the interfacial stability between LATP solid electrolytes and lithium metal anodes for LATP-type solid-state lithium batteries.

A sequential thin-film deposition equipment for in-situ fabricating all-solid-state thin film lithium batteries

High-Voltage All-Solid-State Thin-Film Lithium Batteries Enabled by LiF Interlayer

Fabrication Of Ultrathin Solid Electrolyte Membranes Of Beta-Li3ps4 Nanoflakes By Evaporation-Induced Self-Assembly For All-Solid-State Batteries

In Situ construction of PVDF/LLTO electrolyte with stable electrolyte/electrode interphase for integrated solid-state lithium batteries

Thin Film Deposition Techniques in Surface Engineering Strategies for Advanced Lithium-Ion Batteries

Progress in All-Solid-state Thin Film Lithium/li-Ion Battery

Self-Standing 3D Cathodes for All-Solid-State Thin Film Lithium Batteries with Improved Interface Kinetics

In-situ construction of a Mg-modified interface to guide uniform lithium deposition for stable all-solid-state batteries

Facile Interfacial Modification Via In-Situ Ultraviolet Solidified Gel Polymer Electrolyte for High-Performance Solid-State Lithium Ion Batteries

In situ construction of trinity artificial protective layer between lithium metal and sulfide solid electrolyte interface

Constructing Multifunctional Interphase between Li1.4Al0.4Ti1.6(PO4)(3) and Li Metal by Magnetron Sputtering for Highly Stable Solid-State Lithium Metal Batteries

Physical and electrochemical characterization of amorphous lithium lanthanum titanate solid electrolyte thin-film fabricated by e-beam evaporation

PVA-assisted spray deposited porous Li4Ti5O12 thin film as high-rate and long-cycle anode for lithium-ion thin-film batteries

Engineering and regulating the interfacial stability between Li1.3Al0.3Ti1.7(PO4)3-based solid electrolytes and lithium metal anodes for solid-state lithium batteries

Interface engineering of Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub> ceramic electrolyte via multifunctional interfacial layer for all-solid-state lithium batteries

All-Solid-State Rechargeable Thin Film Lithium Batteries With Lixmn2o4 And Lixmn2o4-0.5zro(2) Cathodes

Smart Construction of Intimate Interface Between Solid Polymer Electrolyte and 3D-Array Electrode for Quasi-Solid-state Lithium Ion Batteries

In Situ Solidification by γ−ray Irradiation Process for Integrated Solid−State Lithium Battery

Long-Cycle Stability of In Situ Ultraviolet Curable Organic/Inorganic Composite Electrolyte for Solid-State Batteries

Artificial Interlayer and Special Electrode Structure Design in a Solid-State Battery to Homogenize Li-Ion Transport

Fabrication and Electrochemical Properties of All Solid State 0.3Ag-V2o5│lipon│li Thin Film Battery