Abstract:The in-house fabricated quasi-network Ti5Si3/TiAl composites showed an excellent combination between light weight and superior high temperature tensile properties in our previous work. However, the deformability was another key factor which determined the Ti5Si3/TiAl composites’ potential for high temperature applications in aeronautics and aerospace. Therefore, in this paper the hot deformation behaviors of the novel quasi-network Ti5Si3/TiAl composites at temperatures from 900 °C to 1200 °C with strain rates in the range of 0.001–1 s−1 was systemically investigated. The results showed that the peak flow stress decreased with the increase in the test temperature and the decrease in the strain rate. The thermal compressive deformation constitutive equation was built, and hence the deformation activation energy of the quasi-network Ti5Si3/TiAl composite was confirmed to be 564.67 kJ/mol, slightly higher than or similar to the TiAl-based alloys fabricated by traditional casting or powder metallurgy. According to the dynamic material model (DMM), the hot processing maps with the true strain of 0.2–0.5 were established. It can be concluded that the instability area was mainly concentrated in the region of low temperature and high strain rate. Combined with the microstructural analysis, the optimal hot processing parameters were the temperature range of 1125–1200 °C and the strain rate of 0.001–0.01 s−1, where a large proportion of dynamic recrystallization occurred. It was noteworthy that the introduction of Ti5Si3 particles was conducive to accelerating the dynamic recrystallization and limiting the dynamic recrystallization grain growth. Besides, the distribution and size of Ti5Si3 particles could be regulated by the hot deformation. Finally, the microstructure evolution mechanism in the hot deformation was discussed in detail, this additionally provided the guidance for the practical plastic forming.

Study on the Deformation of TiNi/AlSi Composite Alloy Using DSCM Method

DIC/DSI Based Studies on the Local Mechanical Behaviors of HR3C/T92 Dissimilar Welded Joint During Plastic Deformation

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

In-situ investigation on tensile properties of a novel Ti/Al composite sheet

Study on the dynamic deformation behavior and microstructure evolution of Ti-5Al-2.5Sn utilized Quasi-In-Situ method

Unraveling hot deformation behavior and microstructure evolution of nanolamellar TiAl/Ti3Al composites

Analysis of Mechanical-Thermal Coupled Experiments of Single Crystal TiNi Alloys

In-situ synchrotron X-ray micro-diffraction investigation of ultra-low-strain deformation microstructure in laminated Ti-Al composites

In-situ investigation of deformation behavior and fracture forms of Ti/Al/Mg/Al/Ti laminates

Study of the high-temperature mechanical properties of Al-6061/NiTi reinforced metal matrix composites

Integrating Experimental and Computational Analyses for Mechanical Characterization of Titanium Carbide/Aluminum Metal Matrix Composites

Research on Hot Deformation Rheological Stress of Al-Mg-Si-Mn-Sc Aluminium Alloy

Investigation of the Physical Properties of the Metal (co, Cr, Mn, Sc) Doped TiAl3 Compounds: A DFT Study

Investigation on the Deformation of TiNi Shape Memory Alloy with a Crack Using Moiré Interferometry

Investigation of α phase evolution and tensile fracture behavior of Ti5Al2Sn2Zr4Mo4Cr alloy fabricated by directed energy deposition

Microstructure and Mechanical Properties of a Novel Al-Mg-Sc-Ti Alloy Fabricated by Laser Powder Bed Fusion

Hot deformation behavior and processing map of novel quasi-network Ti5Si3/TiAl composites

Microstructure and High-Temperature Mechanical Properties of CrMnFeCoNi/TiAl Composites Prepared by Powder Metallurgy

Study on Microstructure and Mechanical Properties of Al-Mg-Si-Cu Aluminium Alloy with High Ductility

Molecular Dynamics Simulation of Tensile Mechanical Properties of Ni/Ni<sub>3</sub>Al

Molecular Dynamics Simulation of Temperature and Ti Volume Fraction on Compressive Properties of Ti/Al Layered Composites