Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

A numerical model for non-linear dynamic analysis of masonry structures subjected to ground motion

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Numerical Simulation And Its Experimental Test On Cracking Process Of Masonry Structures

Numerical Study on Cracking Process of Masonry Structure

Numerical simulation of crack formation process and the mechanic characters of masonry structure

NUMERICAL MODEL AND SIMULATION OF MASONRY FRACTURE PROCESS

Application of Finite Element Analysis in Masonry Structures

Nonlinear Analysis of Masonry Buildings under Seismic Actions with a Multifan Finite Element

Numerical Study on Crack Distributions of the Single-Layer Building under Seismic Waves

Numerical Simulation of the Failure Process of Unreinforced Masonry Walls Due to Concentrated Static and Dynamic Loading

Collapse Process Prediction and Reasonableness Analysis of Masonry Structures Subjected to Strong Earthquake

NUMERICAL SIMULATION OF FAILURE BEHAVIOR OF REINFORCED CONCRETE FRAME STRUCTURES BY DISCRETE ELEMENT METHOD

Simplified mechanical models for the seismic collapse performance prediction of unreinforced masonry structures

Slip-enhanced plastic-damage constitutive model for masonry structures

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Macro-Modeling of Reinforced Concrete Structural Walls: State-of-the-Art

Explicit Approach for the In-Plane Cyclic Behaviors of Unreinforced Masonry Structures Using Finite Particle Method

Numerical homogenization‐based seismic assessment of an English‐bond masonry prototype: Structural level application

Seismic damage evaluation of historical masonry towers through numerical model

Study on Elasto-Plastic Seismic Response and Computational Collapse of Large-Space Brick-Concrete Composite Structures

Numerical Modeling to Predict Seismic Performance of the Post-Tensioned Self-Centering Concrete Shear Walls