Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

Study on Elasto-Plastic Seismic Response and Computational Collapse of Large-Space Brick-Concrete Composite Structures

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Dynamic Progressive Collapse Response of Multi-Storey Frame Structures with Masonry Infills

Large-Scale Experimental Evaluation of Building System Response to Sudden Column Removal

Experimental Study on Progressive Collapse-Resistant Behavior of Reinforced Concrete Frame Structures

Experimental research on a large scale RC frame model subjected to sudden corner column removal

Preliminary study on seismic responses of large-span brick and concrete mixed structures

NUMERICAL SIMULATION OF FAILURE BEHAVIOR OF REINFORCED CONCRETE FRAME STRUCTURES BY DISCRETE ELEMENT METHOD

Simulation of a 3-D Concrete Frame Structure Collapse in Considering Impact Action among Blocks

A numerical model for non-linear dynamic analysis of masonry structures subjected to ground motion

Multi-Scale Analysis Of Damage Process For Concrete Structures

Numerical Simulation for the Progressive Collapse of Concrete Building due to Earthquake

Collapse simulation of reinforced concrete high-rise building induced by extreme earthquakes

Characteristic response and parametric analysis on progressive collapse of concrete-t-filed steel tubular composite frames

Anti-seismic Analysis of Masonry-Reinforced Concrete Composite Structure Based on LS-DYNA

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Simulation of Structural Collapse with Coupled Finite Element-Discrete Element Method

Preliminary Study on Dynamic Progressive Collapse Analysis of Spatial Composite Frames with Concrete-Filled Steel Tubular Columns

Collapse Simulation of Reinforced Concrete Moment Frames Considering Impact Actions among Blocks

NONLINEAR DYNAMIC PROGRESSIVE COLLAPSE ANALYSIS OF COMPOSITE FRAMES WITH CONCRETE-FILLED STEEL TUBULAR COLUMNS BASED ON FIBER MODEL

Nonlinear Simulation Analysis of RC Frame Beam Slab Column Spatial Synergy against Progressive Collapse Performance under Failure of Bottom Corner Columns