Abstract:Vinyl chloride/ N-phenylmaleimide copolymer ( VC/PMI) and vinyl chloride/ N-phenylmaleimide/ acrylonitrile terpolymer (VC/PMI/AN) were synthesized in the suspension copolymerization process for improving the heat resistance of poly( vinyl chloride) PVC) This paper emphasized on the studies on the characterization of the heat resistant properties of these three co) polymers mainly by means of dynamic mechanical experiment with the change of storage modulus ( E'), change rate of E' with temperature and mechanical loss factor ( tandelta) near the glass transition. The Vicat softening point ( VSP) was also tested supplementally for comparison. The lower the change rate of E' with temperature is, the higher the heat resistance of VC/PMI and VC/PMI/AN will be. The effects of the amount of PMI and AN in the recipes of copolymerization on the change rate of E' with temperature, tandelta and VSP were also investigated. The results show that the increase of the amount of PMI will increase the rigidity of the backbone of the copolymer chain so as to improve the heat resistance. On the other hand, the introduction of AN into the copolymer will give more uniform distribution of PMI unit or segment in the backbone, and thus improves the heat resistance of the copolymer further. It is discovered that there are two peaks of mechanical loss or two glass transition temperatures of VC/PMI/AN copolymerization product. It may be interpreted from the higher reactivities of PMI and AN than VC. During the copolymerization process of VC, PMI and AN, the more active PMI and AN will copolymerize more rapidly and will consume entirely at conversion of about 45% similar to 50%. Thereafter, VC continues to homopolymerize to form PVC homopolymer until a final conversion of 85%. Actually, the final product is a mixture of VC/PMI/AN terpolymer and homo-PVC, showing two T(g)s.

Heat-Capacities Of Various Solid Linear Macromolecules

Heat Capacities of Binary Mixtures of Acetic Acid with Acetic Anhydride and Methenamine at Different Temperatures

Macromol. React. Eng. 4/2008

Densities and Viscosities of Binary Mixtures of Cyclopropanecarboxylic Acid with Methanol, Ethanol, Propan-1-ol, and Butan-1-ol at Different Temperatures

Heat capacities and entropies of liquid, high-melting-point polymers containing phenylene groups (PEEK, PC, and PET)

Isobaric Heat Capacity Measurements for Dimethyl Ether and 1,1-Difluoroethane in the Liquid Phase at Temperatures from 305 K to 365 K and Pressures Up to 5 Mpa

Prediction of the heat capacity of main-chain-type polymers below the glass transition temperature

Heat Resistant Properties of Vinyl Chloride-N-Phenylmaleimide (-Acrylonitrile) Suspension Polymerized Copolymer

Vapor Heat Capacities of Some Polar–polar Binary Systems

Thermodynamic Functions of Thermotropic Polyethers Based on the Semiflexible Mesogen 1‐(4‐Hydroxyphenyl)‐2‐(2‐methyl‐4‐hydroxyphenyl)ethane

Barrier Properties of Vinylidene Chloride Methyl Acrylate Copolymer

Isobaric Molar Heat Capacities of 1-Ethyl-3-methylimidazolium Acetate and 1-Hexyl-3-methylimidazolium Acetate Up to 16 MPa

The Molar Heat Capacities of (benzene+tetrachloromethane), (benzene+trichloromethane), (benzene+acetone), and (Acetone+trichloromethane)

The Heat Capacity of Triatomic Gases: An Analytical Approach

Excess Molar Enthalpies of Methyl Acetate and (1-Propanol, 2-Propanol, 1-Butanol, 2-Butanol, and 1-Pentanol) at T = (298.15 and 308.15) K and P = (5.0 and 10.0) MPa

Molecular dynamics and conduction mechanism of poly(vinyl chloride‐co‐vinyl acetate‐co‐2‐hydroxypropyl acrylate) terpolymer containing ionic liquid

The Vapor Heat Capacities of Acetone-Chloroform, Benzene-Carbon Tetrachloride and Benzene-Ethanol Binary Mixtures

Determination of vapor heat capacities of acetone-chloroform, benzene-carbon tetrachloride and benzene-ethanol binary systems

Vapor Heat Capacities of Acetic Acid + 4-Methyl-2-pentanone, at Atmospheric Pressure

Heat Capacities of Fluids: the Performance of Various Equations of State

Molecular Simulation of Caloric Properties of Fluids Modelled by Force Fields with Intramolecular Contributions: Application to Heat Capacities