Abstract:The effects of strain rate on the shear fracture behavior of Sn3.0Ag0.5CuiCu solder joints with thin and thick interfacial intermetallic compound layers were investigated. A single lap-shear sample was designed to conduct the study. The Cu/Sn3.0Ag0.5Cu/Cu joints were reflowed at 250 degrees C and 280 degrees C for 10 min, respectively, resulting in formations of a thin (6.08 mu m) and thick (13.25 mu m) intermetallic compound layer between the solder and Cu substrate. The single lap-shear tests were performed at the shear strain rates of 5 x 10(-4) s(-1), 5 x 10(-3) s(-1), 2 x 10(-2) s(-1), 1 x 10(-1) s(-1) and 2 x 10(-1) s(-1) to observe the shear fracture behavior. Experimental results revealed that both the thickness of the interfacial inter metallic compound layer and strain rate had influence on the shear strength and failure mode of the solder joint. The shear strength of the solder joints increased with increasing strain rate, but decreased with thickness of the interfacial intermetallic compound layer. It was observed that the solder joints broke in a ductile manner at low strain rates (5 x 10(-4) s(-1), 5 x 10(-3) s(-1)), although they exhibited a ductile-brittle mixed manner at intermediate (2 x 10(-2) s(-1)) and a brittle manner at high strain rates (1 x 10(-1) s(-1), 2 x 10(-1) s(-1)). In the case of low strain rates, the ductile fracture behavior of joints with thin and thick intermetallic compound layers were similar. Nevertheless, more cleavage and broken Cu6Sn5 grains were detected on the fracture surface of the solder joint with a thick intermetallic compound layer as the strain rate increased to 2 x 10(-2) s(-1), 1 x 10(-1) s(-1) and 2 x 10(-1) s(-1). Furthermore,, when the strain rate of 2 x 10(-1) s(-1) was applied, the solder joint with a thin intermetallic compound layer was completely broken inside the Cu6Sn5 layer, but partly broken at the Cu6Sn5/Cu3Sn interface for the joints with a thick intermetallic compound layer. Four modes were proposed to explain the detailed ductile-to-brittle transition in failure behavior. In addition, the strain rate sensitivities of the solder joints with thin and thick interfacial intermetallic compound layers were also investigated. It was found that the strain rate of a solder joint with a thick interfacial intermetallic compound layer was lower than that of one with a thin interfacial intermetallic compound layer. (C) 2016 Elsevier B.V. All rights reserved.

Effects of Multiple Reflows on Sn3.8Ag0.7Cu-xNi/Ni Solder Joints

Study on the properties of low silver Sn1.0Ag0.5Cu composite solder reinforced with nickel-plated zinc oxide and its soldering joint

Interfacial microstructure, shear strength and wettability of Ni-added Sn-0.3Ag-0.7Cu/Cu solder joint

Effect of Ni Content on the Microstructure Formation and Properties of Sn-0.7Cu-xNi Solder Alloys

Effects of Ni-decorated reduced graphene oxide nanosheets on the microstructural evolution and mechanical properties of Sn-3.0Ag-0.5Cu composite solders

Effect of Nano-Cu 6 Sn 5 upon development mechanism of Cu–Ni–Sn compounds and mechanical characteristics for mixed solder joints

Effect of Ag, Ni and Bi Additions on Solderability of Lead-Free Solders

Intermetallic compound evolution and mechanical properties of Sn-0.7Cu-0.1Ni-xZn lead-free solder alloys prepared by directional solidification

Effect of Ni-MOF Derivatives on the Electrochemical Corrosion Behavior of Sn-0.7Cu Solders

Microstructure and kinetic analysis of the properties and behavior of nickel (Ni) nano-particle doped tin–zinc–bismuth (Sn–8Zn–3Bi) solders on immersion silver (Ag)-plated copper (Cu) substrates

The influences of reactive nanoparticles alloying on grain boundary and melting properties about Sn3.0Ag0.5Cu solder

Effect of Ni on the Suppression of Sn Whisker Formation in Sn-0.7Cu Solder Joint

Effects of Addition Small Amount High Melting Point Metal on Properties of Lead-free Solders

Mechanical properties and intermetallic compound formation at the Sn/Ni and Sn-0.7wt.%Cu/Ni joints

Microstructure and shear property of Ni-coated carbon nanotubes reinforced InSn-50Ag composite solder joints prepared by transient liquid phase bonding

Shear Strength and Fracture Analysis of Sn-9Zn-2.5Bi-1.5In and Sn-3.0Ag-0.5Cu Pastes with Cu-substrate Joints under Different Reflow Times

Effects of Ni-coated Carbon Nanotubes addition on the electromigration of Sn-Ag-Cu solder joints

Diffusion reaction-induced microstructure and strength evolution of Cu joints bonded with Sn-based solder containing Ni-foam

Study of New Types Lead-Free Solder Alloys of Sn-Ag-Cu-Al-Ni and Sn-Zn-Bi-In-P

Microstructure evolution and grain refinement of ultrasonic-assisted soldering joint by using Ni foam reinforced Sn composite solder

Shear Strength and Fracture Behavior of Reflowed Sn3.0ag0.5cu/Cu Solder Joints under Various Strain Rates